Abstract:Compressible flow past a circular cylinder at an inflow Reynolds number of 2 x 10 5 is numerically investigated by using a constrained large-eddy simulation (CLES) technique. Numerical simulation with adiabatic wall boundary condition and at a free-stream Mach number of 0.75 is conducted to validate and verify the performance of the present CLES method in predicting separated flows. Some typical and characteristic physical quantities, such as the drag coefficient, the root-mean-square lift fluctuations, the Strouhal number, the pressure and skin friction distributions around the cylinder, etc. are calculated and compared with previously reported experimental data, finer-grid large-eddy simulation (LES) data and those obtained in the present LES and detached-eddy simulation (DES) on coarse grids. It turns out that CLES is superior to DES in predicting such separated flow and that CLES can mimic the intricate shock wave dynamics quite well. Then, the effects of Mach number on the flow patterns and parameters such as the pressure, skin friction and drag coefficients, and the cylinder surface temperature are studied, with Mach number varying from 0.1 to 0.95. Non-monotonic behaviors of the pressure and skin friction distributions are observed with increasing Mach number and the minimum mean separation angle occurs at a subcritical Mach number of between 0.3 and 0.5. Additionally, the wall temperature effects on the thermodynamic and aerodynamic quantities are explored in a series of simulations using isothermal wall boundary conditions at three different wall temperatures. It is found that the flow separates earlier from the cylinder surface with a longer recirculation length in the wake and a higher pressure coefficient at the rear stagnation point for higher wall temperature. Moreover, the influences of different thermal wall boundary conditions on the flow field are gradually magnified from the front stagnation point to the rear stagnation point. Moreover, the influences of different thermal wall boundary conditions on the flow field are graduallymagnified from the front stagnation point to the rear stagnation point. It is inferred that the CLES approach in its current version is a useful and effective tool for simulating wall-bounded compressible turbulent flows with massive separations.

Investigation on engine in-cylinder turbulent flow and coherent structure based on large eddy simulation

Research on In-cylinder Cold Flow of a Two Stoke Engine with A Large Eddy Simulation

Constrained Large-Eddy Simulation of Compressible Flow Past a Circular Cylinder

Constrained Large Eddy Simulation of Wall-Bounded Turbulent Flows

Constrained Large-Eddy Simulation and Detached Eddy Simulation of Flow Past a Commercial Aircraft at 14 Degrees Angle of Attack

Analysis of In-cylinder Flow Field Anisotropy in IC Engine using Large Eddy Simulation

LARGE EDDY SIMULATION FOR INTERNAL COMBUSTION ENGINES: PROGRESS AND PROSPECTS

New Insight on Large-Eddy Simulation of Flow Past a Circular Cylinder at Subcritical Reynolds Number 3900

Large Eddy Simulation of Unconfined Turbulent Swirling Flow

Three-Dimensional Computational Fluid Dynamics Modeling of a 6V150 Diesel Engine

Studies on a Swirling Heptane Spray Flame by Large-Eddy Simulation

Large Eddy Simulation of Intake and Spray Process in a GDI Engine

Investigation of Very Large Eddy Simulation Method for Applications of Supersonic Turbulent Combustion

Investigation of the Coherent Structure in a Particle -laden Turbulent Planar Jet Using LES

Large-eddy Structures of Turbulent Swirling Flows and Methane-Air Swirling Diffusion Combustion

Large eddy simulation analysis of the turbulent flow in an optically accessible internal combustion engine using the overset mesh technique

Large eddy simulation of reactive flow in a bluff-body combustion chamber

Application of Large Eddy Simulation in the process of the Multi-Physics Field Coupling in a Combustion Chamber

Turbulent Flow Simulation Using Large Eddy Simulation Combined with Characteristic-Based Split Scheme

Multi-plane Time-Resolved Particle Image Velocimetry (PIV) Flow Field Measurements in an Optical Spark-Ignition Direct-Injection (SIDI) Engine for Large-Eddy Simulation (LES) Model Validations

Finite Element Analysis of Turbulent Flows Using Les and Dynamic Subgrid-Scale Models in Complex Geometries