Abstract:Carbon nanotubes (CNTs) are considered an advanced form of carbon. They have superior characteristics in terms of mechanical and thermal properties compared to other available fibers and can be used in various applications, such as supercapacitors, sensors, and artificial muscles. The properties of single-walled carbon nanotubes (SWNTs) are significantly affected by geometric parameters such as chirality and aspect ratio, and testing conditions such as temperature and strain rate. In this study, the effects of geometric parameters and temperature on the mechanical properties of SWNTs were studied by molecular dynamics (MD) simulations using the Large-scaled Atomic/Molecular Massively Parallel Simulator (LAMMPS). Based on the second-generation reactive empirical bond order (REBO) potential, SWNTs of different diameters were tested in tension and compression under different strain rates and temperatures to understand their effects on the mechanical behavior of SWNTs. It was observed that the Young’s modulus and the tensile strength decreases with increasing SWNT tube diameter. As the chiral angle increases, the tensile strength increases, while the Young’s modulus decreases. The simulations were repeated at different temperatures of 300 K, 900 K, 1500 K, 2100 K and different strain rates of 1 × 10−3/ps, 0.75 × 10−3/ps, 0.5 × 10−3/ps, and 0.25 × 10−3/ps to investigate the effects of temperature and strain rate, respectively. The results show that the ultimate tensile strength of SWNTs increases with increasing strain rate. It is also seen that when SWNTs were stretched at higher temperatures, they failed at lower stresses and strains. The compressive behavior results indicate that SWNTs tend to buckle under lower stresses and strains than those under tensile stress. The simulation results were validated by and consistent with previous studies. The presented approach can be applied to investigate the properties of other advanced materials.

Investigation of the thermo-mechanical properties of single-walled carbon nanotubes based on the temperature-related higher order Cauchy-Born rule

Coupled Thermomechanics Of Single-Wall Carbon Nanotubes

Meshless simulation for thermo-mechanical properties of single-walled carbon nanotubes based on the thermal-related higher order Cauchy-Born rule

Influence of temperature change on column buckling of multiwalled carbon nanotubes

Thermal Effect on Transverse Vibrations of Double-Walled Carbon Nanotubes

Experimental Investigation and Modelling on the Thermal Conductivity of CNTs Based Nanofluids

Thermal Conductivity Of Configurable Two-Dimensional Carbon Nanotube Architecture And Strain Modulation

Structure and thermophysical properties of single-wall Si nanotubes

Interfacial Thermal Conductance of Buckling Carbon Nanotubes

Molecular Dynamics Simulations of Effects of Geometric Parameters and Temperature on Mechanical Properties of Single-Walled Carbon Nanotubes

The Effect of Nanotube Radius on the Constitutive Model for Carbon Nanotubes

Computational Study of the Nanoscale Mechanical Properties of C-S-H Composites under Different Temperatures

Thermomechanical Modeling of Scanning Joule Expansion Microscopy Imaging of Single-Walled Carbon Nanotube Devices

Mechanical and Thermal Properties of Graphyne-Coated Carbon Nanotubes: a Molecular Dynamics Simulation on One-Dimensional All-Carbon Van Der Waals Heterostructures

The Intrinsic Stiffness of Single-Wall Carbon Nanotubes

Ultrahigh Convergent Thermal Conductivity of Carbon Nanotubes from Comprehensive Atomistic Modeling

Molecular dynamics simulation studies of mechanical properties of different carbon nanotube systems

A comparative study of Young’s modulus of single-walled carbon nanotube by CPMD, MD and first principle simulations

Mechanical Properties of Single-Walled Carbon Nanotube Bundles As Bulk Materials

Effects of Topological Parameters on Thermal Properties of Carbon Nanotubes via Molecular Dynamics Simulation

Micromechanics-based modeling of elastic modulus and coefficient of thermal expansion for CNT-metal nanocomposites: effects of waviness, clustering and aluminum carbide layer