Abstract:To investigate the effect of the sintering temperature on the microstructure characteristics of porous NiTi alloys, two types of porous NiTi alloys with equal atomic ratios were fabricated via elemental powder sintering at 950 °C and 1000 °C. Afterwards, optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were collectively applied to investigate the pore characteristics and microstructure of the fabricated porous NiTi alloy. The results show that when the sintering temperature increases from 950 °C to 1000 °C, the average pore size increases from 36.00 μm to 181.65 μm, owing to the integration of these newly formed small pores into these pre-existing large-sized pores. The measured density increases from 2.556 g/cm3 to 3.030 g/cm3, while the porosity decreases from 60.4% to 51.8%. This is due to the occurrence of shrinkage after the sufficient diffusion of atoms. Furthermore, the characterization results confirm that a change in the sintering temperature would not change the phase types within a porous NiTi alloy; namely, the matrix consists primarily of B2 NiTi, with a significant amount of Ni4Ti3 precipitates and a small amount of Ni3Ti precipitates and Ti2Ni precipitates. However, as the sintering temperature increases, the number of Ni4Ti3 precipitates decreases significantly. The formation of a Ni4Ti3 phase in the present study is closely related to the enrichment of Ni content in the matrix owing to the diffusion rate difference between Ni atoms and Ti atoms and the absence of a transient liquid phase (TLP) during the sintering process owing to the relatively low sintering temperature (lower than the eutectic temperature). Moreover, the increasing sintering temperature speeds up the atom diffusion, which contributes to a reduction in the enrichment of Ni as well as the number of formed Ni4Ti3 precipitates.

Effect of sintering neck on compressive mechanical properties of porous titanium

Effect of Porosity on Compressive Properities of Porous Titanium with Helical Pores Structure

Effect of Sintering Temperature on Microstructure and Properties of Porous Titanium

Preparation, Microstructure and Mechanical Properties of Porous Titanium Sintered by Ti Fibres

Flexural and compressive mechanical behaviors of the porous titanium materials with entangled wire structure at different sintering conditions for load-bearing biomedical applications.

Effects of pore microstructures on thermal and mechanical properties of porous TiC fabricated by hot press sintering

Effects of Pore Size and Porosity on Cytocompatibility and Osteogenic Differentiation of Porous Titanium

Fabrication and Mechanical Properties of Porous Tib2 Ceramic

Effect of Pore Sizes on the Microstructure and Properties of the Biomedical Porous NiTi Alloys Prepared by Microwave Sintering

Experimental research on porous titanium implant fabricated by three-dimensional printing with different sintering temperatures

Effect of Sintering Temperature on Microstructure Characteristics of Porous NiTi Alloy Fabricated via Elemental Powder Sintering

Porous titanium-niobium alloys with different porosities:biomechanical strength and cytocompatibility

Fabrication and Characterization of Porous TiB2 Ceramic with Three-Dimensional Interconnected Skeleton

Correlation between pore structure and compression behavior of porous sintered Cu-Ni-Cr alloy at elevated temperatures

Evaluation of channel-like porous-structured titanium in mechanical properties and osseointegration

Effect of Microstructure on the Tensile Property of Porous Ti Produced by Powder Metallurgy Technique

Insights into unit cell size effect on mechanical responses and energy absorption capability of titanium graded porous structures manufactured by laser powder bed fusion

Fabrication of Porous Titanium Implants by Three-Dimensional Printing and Sintering at Different Temperatures.

Effect of Sintering Temperature on the Structures and Properties of Porous Aluminium Titanate Ceramics

Fabrication and Characterization of Porous Titanium Based on TPMS Structure