Abstract:Forming limit diagrams (FLDs) are very important in predicting the behavior of the sheet. Therefore, predicting and drawing these diagrams by theoretical and experimental methods has been one of the main objectives of this paper. In this paper, the formability behavior of 5083 aluminum sheet was investigated by considering the strain hardening behavior. Tensile tests has performed in seven directions 0°, 15°, 30°, 45°, 60°, 75° and 90° from the rolling direction due to identify and calibrate coefficients of BBC2008 advanced yield criteria. The yield stresses was defined in the plane strain mode, also the anisotropy coefficients and the appropriate error function were extracted and then the relationships of the plane strain yield stress were added to the error function. The error function was optimized using Genetic Algorithm and limit strains were calculated using yield coefficients. The results showed that if the strain hardening exponent increases by 0.1, the limit strains increase by 30 to 40%. Also the results showed that the initial imperfection factor ( 𝑓 0 ) has a great effect on determining the FLD and with a very small change, it has a great effect on the FLD; So that by increasing this factor to about 0.016, the values of the limit strains are almost doubled. Using the results of this paper and having sheet properties such as yield strengths and anisotropy coefficients and proper selection of yield criteria, the FLD of different sheets to be theoretically determined with acceptable accuracy. [1] Plastic Instability and Fracture in Sheet Stretched over Rigid Punches. [2] Application of strain analysis to sheet metal forming problems in the press shop. [3] On discontinuous plastic states, with special reference to localized necking in thin sheets. [4] Limit strains in the processes of stretch-forming sheet metal. [5] The influence of strain-path changes on forming limit diagrams of A1 6111 T4. [6] Investigation of formability of low carbon steel sheets by forming limit diagrams. [7] Theoretical determination of forming limit diagram for steel, brass and aluminum alloy sheets. [8] Experimental and numerical evaluation of forming limit diagram for Ti6Al4V titanium and Al6061-T6 aluminum alloys sheets. [9] Experimental and numerical analysis of forming limit diagram (FLD) and forming limit stress diagram (FLSD). [10] Forming limit and fracture mechanism of ferritic stainless steel sheets. [11] Calculation of forming limit diagrams using Hill's 1993 yield criterion. [12] The effects of anisotropic yield functions and their material parameters on prediction of forming limit diagrams. [13] The Effect of Advanced BBC2003, Yld2004 and BBC2008 Yield Criteria on FLDs Based on MK, Swift's and Hill's Models. [14] An experimental and theoretical investigation for determination of yield criteria parameters... [15] The forming limit curve for multiphase advanced high strength steels... [16] Forming limits of dual phase steels using crystal plasticity in conjunction with MK approach. [17] Prediction of FLD for sheet metal by considering through-thickness shear stresses. [18] Investigation on the effective range of the through thickness shear stress... [19] Controlling factors of forming limit curve: A review. [20] Crystal plasticity finite element – Marciniak-Kuczynski approach with surface roughening effect... [21] Plane stress yield criterion for highly anisotropicsheet metals. [22] Techniques of measurement of body composition Part II. [23] An improved analytical description of orthotropy in metallic sheets. [24] A study of microstructure and tribological properties of Al 5083 MMC processed by direct extrusion. [25] A novel and simple method for the measurement of plane strain work hardening.

Experimental measurement and theoretical prediction of forming limit curve for aluminum alloy 2B06

Prediction of Forming Limit Curve (FLC) for Al–Li Alloy 2198-T3 Sheet Using Different Yield Functions

Prediction of Forming Limit Curves for 2021 Aluminum Alloy

Forming Limit of FSW Aluminum Alloy Blank Based on a New Constitutive Model

An Investigation on Anisotropy Behavior and Forming Limit of 5182-H111 Aluminum Alloy

Predicting the fracture forming limit of 5754-O aluminum alloy by finite element simulation

A Numerical M-K Approach for Predicting the Forming Limits of Material AA5754-O

Investigation on the Forming Limits of 5754-O Aluminum Alloy Sheet with the Numerical Marciniak–Kuczynski Approach

Theoretical Prediction of FLDs for Al-Li Alloy at Elevated Temperature Based on M-K Model

Theoretical and experimental research on aluminum alloy beams

Experimental and Theoretical Investigations of the Forming Limit of 5754O Aluminum Alloy Sheet under Different Combined Loading Paths

Numerical prediction and experimental validation of forming limit curves of laminated half-hard aluminum sheets

Comparative Investigation of the Experimental Determination of AA5086 FLCs under Different Necking Criteria

Prediction and Experimental Validation of Forming Limit Curve of a Quenched and Partitioned Steel

Research on the thermal forming limit diagram (TFLD) with the M-K model for Ti-6Al-4V alloy

Characterization of Forming Limits at Fracture for Aluminum Alloy 6K21-T4 Sheets in Non-Linear Strain Paths Using a Biaxial Tension/shear Loading Test

Effect of Through-Thickness Normal Stress on Forming Limits under Yld2003 Yield Criterion and M-K Model

Experimental and Theoretical Study of Formability Behavior of Aluminum Alloy 5083 Sheet for Determination of Advanced Anisotropic Yield Criteria Coefficient and Prediction of Forming Limit Diagram

Theoretical and Numerical Investigation of the Limit Strain of a 5754-O Aluminum Alloy Sheet Considering the Influence of the Hardening Law

Forming Limit Calculation Based on the M-K Model with Yld96 Yield Function

Predicting Sheet Forming Limit of Aluminum Alloys for Cold and Warm Forming by Developing a Ductile Failure Criterion