Abstract:Hydraulic fracturing techniques are often applied to form permeability enhancement zones near boreholes and/or wellbores in tight low-permeability reservoirs to improve their extraction efficiency. As conventional hydraulic fracturing techniques often generate high breakdown pressure and induced seismic potential, novel alternative production enhancement techniques (such as pulse hydraulic pressurization) have been proposed. However, their applicability requires further verification. Therefore, this study conducted hydraulic fracturing tests of coal under three test schemes: conventional hydraulic fracturing (CHF), stepwise pressurization hydraulic fracturing (SPHF), and stepwise pulse pressurization hydraulic fracturing (SPPHF), considering the true triaxial stress state of an actual coal seam. The results showed that the breakdown pressure of coal decreased with an increase in the horizontal stress difference ( σ 2 - σ 3 ). Moreover, the pulse pressurization produced more intergranular fractures and caused a large number of particles to be conducted as a stress concentrator at the fracture tip spalling, which promoted the unstable propagation of fractures, which decreased the breakdown pressure of coal. The abnormally high breakdown pressure in the SPHF experiments is likely due to the obstruction of high σ 2 to the fracture propagation rate and fluid injection, which intensifies the fluid hysteresis effect and the stable fracture development and expansion during the pressure-maintaining stage, thus increasing the breakdown pressure. To describe the relationship between the variation in the breakdown pressure and fracture evolution characteristics, we introduced the equivalent characteristic length l and established a breakdown pressure prediction model based on the tensile stress criterion, which shows effective prediction of the breakdown pressure in different test schemes. Anisotropic principal strain appeared under different injection schemes. During the CHF and SPHF experiments, fluid injection deformed the σ 1 direction by compression and the σ 3 direction by expansion. In the σ 2 direction, the deformation transitioned from expansion at a low stress level to compression at a high stress level. The deformation in the σ 2 direction was always compressive in the SPPHF experiments. Continuous and pulse pressurizations can promote the deformation and fracture development. For the fracture morphology, the coal in the CHF experiments was dominated by a single tensile fracture, and macroscopic shear fractures were formed in the SPHF and SPPHF experiments owing to the continuous stimulation of fluid pressure to the bonding of particles and the weak surface structure, such as bedding and cleats during the pressure maintenance and pulse, and the fragmentation effect was significant and accompanied by obvious particle spalling.

Damage Mechanism of Coal Powder on Fracture Conductivity

Experimental Modeling of Sanding Fracturing and Conductivity of Propped Fractures in Conglomerate:A Case Study of Tight Conglomerate of Mahu Sag in Junggar Basin,NW China

Experimental Method to Simulate Coal Fines Migration and Coal Fines Aggregation Prevention in the Hydraulic Fracture

Mechanism of Single Proppant Pressure Embedded in Coal Seam Fracture

Experimental evaluation of conductivity of fracturing in medium and high-rank coal beds

An Experimental Study on the Impact of the Particle Size and Proportion of Composite Proppant on the Conductivity of Propped Fractures in Coalbed Methane Reservoirs following Pulverized Coal Fines Infiltration

Investigating the proppant damage mechanisms expected in a propped coal fracture and its effect on fracture flow

Micro-structural Damage to Coal Induced by Liquid CO2 Phase Change Fracturing

Study on the Permeability Enhancement of Propped Fractures under the Action of a Coal Fine Plugging Removal Agent

Numerical Simulation of Fracturing in Coals Using Water and Supercritical Carbon Dioxide with Potential-Based Cohesive Zone Models

Numerical Simulation of Crack Initiation and Propagation Evolution Law of Hydraulic Fracturing Holes in Coal Seams Considering Permeability Anisotropy and Damage

Influence of Proppant Parameters on Hydraulic Fracture Conductivity

Study on the Fractal Characteristics and Seepage Properties of Channels Filled by Coal Particles

Effect of Flow Velocity on Clogging Induced by Coal Fines in Saturated Proppant Packs: A Transition from Surface Deposition to Bridging

Effective application of proppants during the hydraulic fracturing of coal seam gas reservoirs: Implications from laboratory testings of propped and unpropped coal fractures

Numerical Simulation Study on Electrical Properties of Proppant-Containing Fracture Fillers

A numerical investigation of hydraulic fracturing on coal seam permeability based on PFC-COMSOL coupling method

Experimental study on deformation and fracture characteristics of coal under different true triaxial hydraulic fracture schemes

Crack Damage Propagation and Morphology Distribution of Hydraulic Electric Pulse Fractured Coal

Experimental and numerical investigation on failure characteristics and mechanism of coal with different water contents

Fracture propagation and pore pressure evolution characteristics induced by hydraulic and pneumatic fracturing of coal