Abstract:The cell performance and Pt utilization of low-Pt proton exchange membrane fuel cells (PEMFCs) have been significantly improved through incorporating carbon materials into the conventional Pt/C catalytic layer of the membrane electrode assembly (MEA). However, the introduction methods for the carbon materials have not been investigated. In this work, carbon nanotube (CNT) as an additive was added to the low-Pt loading catalytic layer (0.1 mg(Pt).cm(-2)) by two methods: a separated CNT layer deposited on the top of the conventional Pt/C layer (CCM-1) and a mixture layer by blending CNT and Pt/C catalyst (CCM-2). The conventional low-Pt loading catalytic layer was employed as control group (CCM-0). The microstructure of the catalytic layers was characterized by scanning electron microscopy, transmission electron microscopy and nitrogen sorption isotherms method. The electrochemical properties of the catalytic layer and membrane electrode were evaluated by cyclic voltammetry (CV), electrochemical impedance (EIS) and linear scanning voltammetry. The results indicated that the cell performance of the conventional low-Pt loading catalyst coated membrane was improved by the introduction of CNTs in both CCM-1 and CCM-2. Compared to the conventional CCM (CCM-0) with a peak power density of 0.522 W.cm(-2) at 70 degrees C and 100% relative humidity (RH) without backpressure, the maximum power densities of CCM-1 and CCM-2 have been improved by 22.4% and 60.0% under the same test conditions, respectively. The increased performance of CCM-1 is believed to result from the enhancement of contact interface between the catalytic layer and the gas diffusion layer in CCM-1 and consequent decrease of the contact resistance. Furthermore, the outstanding power density of CCM-2 is not only owing to the decreased interface contact resistance between the CCM and the gas diffusion layer, but also due to the significant improvement of gas transmission in the catalytic layer, which leads to the decrease of electrochemical reactant resistance and then improvement of the Pt utilization. That has been confirmed by the Pt utilization of 34.4%, 35.6% and 44.7% for CCM-0, CCM-1 and CCM-2. In addition, it also was confirmed by the extremely low power output (2.9 mW.cm(-2)) of a CCM with only CNT in the catalytic layer when the fuel cell was tested at 70 degrees C and 100% RH without back pressure. In addition, the optimum loading of CNT in the mixed catalytic layer is 37.5 mu g.cm(-2) with the peak power density of 0.91 W.cm(-2). This work shows that mixing of CNT and Pt/C catalyst into a catalytic layer is an effective method for improving the Pt utilization and reducing the loading of Pt catalyst.

Effect of Pt Content on the Structure and Performance for Membrane Electrode Assemblies

Preparation of Membrane Electrode Assemblies for Proton Exchange Membrane Fuel Cells

An Effective Method of Applying Octahedral Pt-Ni/C to Membrane Electrode Assembly and Related In-Situ X-ray Absorption Fine Structures Study

Membrane Electrode Assembly Based on Buckypaper with Gradient Distribution of Platinum, Proton Conductor and Electrode Porosity

Improving the performance and durability of low Pt-loaded MEAs by adjusting the distribution positions of Pt particles in cathode catalyst layer

Development of Cathode Ordered Membrane Electrode Assembly Based on TiO2 Nanowire Array and Ultrasonic Spraying

Preparation and Performance of Electrocatalytic Layer of Membrane Electrode Assemblies in PEMFC

Effect of Metal Particle Size and Nafion Content on Performance of MEA Using Ir-V/C As Anode Catalyst

In-Situ X-Ray Absorption Fine Structures Study for the Application of the Octahedral Pt-Ni/C Catalyst in Membrane Electrode Assembly

Effect of Ionomer Content on Cathode Catalyst Layer for PEMFC Via Molecular Dynamics Simulations and Experiments

Optimizing the structural design of cathode catalyst layer for PEM fuel cells for improving mass-specific power density

Effect of Addition of Carbon Nanotubes on the Performance of a Low Pt Loading Membrane-Electrode-Assembly in Proton Exchange Membrane Fuel Cells

Performance Optimization of Ultra-Low Platinum Loading Membrane Electrode Assembly Prepared by Electrostatic Spraying

Study on the Membrane Electrode Assembly Fabrication with Carbon Supported Cobalt Triethylenetetramine As Cathode Catalyst for Proton Exchange Membrane Fuel Cell

Effect of Preparation Conditions of Catalyst-Coated Membrane on Its Performance in Proton Exchange Membrane Fuel Cells

Effect of the Fabrication Condition of Membrane Electrode Assemblies with Carbon-Supported Ordered PtCo Electrocatalyst on the Durability of Polymer Electrolyte Membrane Fuel Cells

A Highly Order‐Structured Membrane Electrode Assembly with Vertically Aligned Carbon Nanotubes for Ultra‐Low Pt Loading PEM Fuel Cells

The Influence of Membrane Thickness and Catalyst Loading on Performance of Proton Exchange Membrane Fuel Cells

Enhancing membrane electrode assembly performance by improving the porous structure and hydrophobicity of the cathode catalyst layer

Investigation of a Novel Catalyst Coated Membrane Method to Prepare Low-Platinum-Loading Membrane Electrode Assemblies for PEMFCs

The Performance Improvement of Membrane and Electrode Assembly in Open-Cathode Proton Exchange Membrane Fuel Cell