Fuel Cell Control System Based on LabVIEW

LIU Yi-cheng,TIAN Zuo-hua

DOI: https://doi.org/10.3969/j.issn.1000-8829.2009.03.004

2009-01-01

Abstract:A control system of 9 kW PEM fuel cell monitor system is introduced,which uses industrial computer and LabVIEW as the software platform.It effectively controls the oxygen supply system,hydrogen supply system and cooling system and gives a user-friendly graphical interface.

What problem does this paper attempt to address?

High temperature proton exchange membrane fuel cell hybrid power system monitoring platform designing

Hongye Su,Bo Zhang,Zhixing Cao,XiuLiang Li,Xuelan Chen

DOI: https://doi.org/10.1049/cp.2012.1177

2012-01-01

Abstract:The design of 5kw high temperature proton exchange membrane fuel cell (HTPEMFC) hybrid power system monitoring platform is presented in this paper. The purpose of the system is to overcome the problems of low temperature proton exchange membrane fuel cell (LTPEMFC), such as poor water management and requirement of high-purity hydrogen. The present computerized real-time monitoring system is based on NI's PXIe hardware system and Labview software. The platform has two working modes - test mode and simulation mode. In the test mode, it provides the conditions for studying the problems of fuel cell hybrid power system, such as system performance, modelling and optimization, by completely monitoring all the working parameters in real-time. And in the simulation mode, besides the problems mentioned above, those with feeding control under changing loads, stability of output power and optimization of energy efficiency, can also be studied with multi-energy management system.
Design of a 5 Kw Distributed Grid-connected Fuel Cell Power System

朱选才,沈国桥,徐德鸿

DOI: https://doi.org/10.3969/j.issn.1000-100x.2009.10.010

2009-01-01

Abstract:The design of a 5 kW distributed grid-connected proton exchanged membrane(PEM) fuel cell power system is introduced.The system structure and main circuit configuration are given.Then the control design based on weighted average current feedback for grid current control and the design of the energy management unit are introduced.Finally,the experimental results upon a prototype are given to verify the design.From the experimental results,we know that the proposed system can operate well under both stand-alone and grid-connected modes.The fuel cell safety can be guaranteed by the energy management unit by compensating the dynamic power during load transition.
Neutral Point Voltage Control For Three-Level Fuel Cell Power Conversion System

Xiaohui Li,Wenping Zhang,Chengrui Du,Xiaotian Wu,Dehong Xu

DOI: https://doi.org/10.1109/PEDG.2010.5545859

2010-01-01

Abstract:A three-level Power Conversion System (PCS) for fuel cell (FC) is investigated. The three-level PCS is composed of a diode clamped three-level inverter and a three-level DC/DC converter, which have the common neutral point. To suppress variation of the neutral point voltage of three-level PCS, a novel control strategy is presented by the three-level DC/DC converter. Through modeling of fuel cell power conversion system, the neutral point voltage control is derived. The control loops are designed. The control strategy is verified by simulation and experiments. The neutral point voltage and DC-bus voltage control are achieved excellently both on static and dynamic conditions.
Design of Energy Management Control in Fuel Cell Power System

ZHU Xuan-cai,XU De-hong,WU Ping,CAO Lu-ping,SHEN Guo-qiao

DOI: https://doi.org/10.3321/j.issn:0258-8013.2008.11.018

2008-01-01

Abstract:Fuel cell is known as a application with slow dynamic response.The energy management design for fuel cell power system is discussed to solve the limitation.The structure and the controller design of the energy management system are discussed.An energy management control system based on indirectly current control is proposed.The system model is obtained based on a practical fuel cell power system.The design process of the energy management control system is presented and the current control loop design is discussed in detail.In addition,an arithmetic scheme based on stage transition diagram is designed to manage the energy storied in the super capacitor.Finally,the experiment results on a 5 kW fuel cell power system with energy management are given to verify the theoretical analysis.
Monitor System of Energy-Feedback Electronic Load Based on CAN Bus and LabVIEW

CHEN Xue-bing,GUO Qian,MA Hao

DOI: https://doi.org/10.3969/j.issn.1001-4551.2011.08.014

2011-01-01

Abstract:In order to realize the automatic control and real-time data acquisition during the burn-in test of the power supplies,a monitor system was designed for the energy-feedback electronic load system with CAN bus and LabVIEW.The energy-feedback electronic load system contains 72 electronic load units with 3 kW which distribute in 8 cabinets.Each unit was controlled by DSP.The monitor system consists of RS-485 buses inside the units,CAN buses of cabinet level and one CAN bus of system level.By means of LabVIEW,a human machine interface(HMI) for monitoring and controlling was developed on PC.With the 3-level buses,the PC can communicate with each DSP and start or stop the whole electronic load system.Furthermore,the output currents of power supplies under testing were set by PC.The monitor system acquires the real-time output voltages and currents of the power supplies during the test.The practical results demonstrate that the monitor system is real-time and reliable.It achieves good performance.
Development of Simulation and Real Time Control Platform for Fuel Cell Powertrain

Jin Zhenhua,Ouyang Minggao,Lu Qingchun,Gao Dawei

2008-01-01

Abstract:Based on virtual instrument development workbench,simulation and real time control system for fuel cell powertrian was developed and a model based controller development platform was constructed.Sub-systems of the powertrain were modeled and simulation software was developed with LabVIEW Simulation module.Real time control system was constructed with embedded PC and LabVIEW real time module.Application of the platform shows the system works well.
Design of PEMFC voltage monitor system based on USB

NIU Jing-bin,ZHU Xin-jian,HU Wan-qi

DOI: https://doi.org/10.3969/j.issn.1001-1579.2009.01.010

2009-01-01

Abstract:Based on the distributed control system(DCS)technology,a multiply boards and multiply single-chip microcomputer voltage monitor system was brought out.USB bus technology and the LabVIEW language were closely integrated by virtual COM technology.The overall design of the proton exchange membrane fuel cell(PEMFC)voltage monitor system based on USB was given,the critical components which impacted on system performance were introduced,such as the microprocessor,A/D converter controller and the interface converter chip.
Automatic Code Generation for Fuel Cell Control System

Xia Wenchuan,Liu Yuan,Lu Languang,Li Jianqiu,Ouyang Minggao

DOI: https://doi.org/10.3321/j.issn:1000-680X.2005.06.003

2005-01-01

Abstract:This paper presents a method of automatic code generation,based on control algorithm of Simulink model with self-developed software / hardware platform.By using this method,the rapid iteration is realized in the development process of fuel cell control system with Motorola Power PC555-based electronic control unit and OSEK Turbo real-time operating system and finally the development of rapid control prototype is achieved.The control system has been verified by the test on a 10kW fuel cell engine and shows very good control performance.
A Distributed Real-Time Control System For Pem Fuel Cell Engine

Jianqiu Li,Liangfei Xu,JianFeng Hua,Minggao Ouyang

DOI: https://doi.org/10.1115/FuelCell2009-85203

2009-01-01

Abstract:A real time distributed control system for a 100Kw PEM fuel cell engine will be presented in this paper. The fuel cell engine is successful applied to a demonstration city bus in Beijing city for the Olympic Games. The framework of the control system, which is based on the Time Trigger Controller Area Network (TTCAN), will be presented in this paper. The control task schedule and optimize of TTCAN are analyzed. The individual and flexible output power control of the FC blocks is discussed and then the improved solution is presented.
Design of Monitoring System for Microgrid of Wind-Hydrogen-Fuel Cell Based on KingView Software

Jianliang ZHANG,Dong-lian QI,Yue WU,Tao HAN,Lingxia LU

DOI: https://doi.org/10.19927/j.cnki.syyt.2017.06.009

2017-01-01

Abstract:A KingView based wind-hydrogen-fuel cell microgrid monitoring system is designed to implement the coordinated control of the wind turbine generation system,electrolytic hydrogen production system,compressed hydrogen storage system and fuel cell generation system.The hardware and software components of the system are introduced,and the technical route and the development process are described in detail.The development and application of microgrid monitoring system will not only implement three different operating modes including the wind power hydrogen production and storage operation mode,the fuel cell power generation operating mode as well as microgrid system-wide operation mode,ensuring a safe and stable operation of the microgrid system,but also help to provide a platform for the students of electrical engineering to carry out exploratory experiments in the cutting-edge technology in distributed generations and microgrid,and provide a strong experimental support conditions for teaching and research staffs to promote teaching reform and scientific research in the field of smart grid and microgrid.
Development of Data Management Software for Fuel-cell Bus Demonstration Operation

ZHU Peng,JIN Zhen-hua,YAN Dong-lin

DOI: https://doi.org/10.3969/j.issn.1005-2550.2007.06.013

2007-01-01

Abstract:Fuel-cell buses are now tested in simulating working.To evaluate the economy and reliability performances,a set of data management software, based on Microsoft Access database,is developed with LabView. This gives a kind of acceptable sample about FCB evaluation system on economy and reliability performances, and was already put in use.
Design and research of fuel cell experiment plat

Meng SHAO,Xin-jian ZHU,Hong-fei CAO,Zhao-hui WU

DOI: https://doi.org/10.3969/j.issn.1002-087X.2017.07.012

2017-01-01

Abstract:A novelty fuel cell experiment plat was design for 7 kW PEMFC stacks.For the stability and reliability of this experiment plat,SIEMENS SIMATIC S7-1200 PLC was used for main controller.In this paper,an ANN (artificial neural network) method was presented that improves the temperature control of hydrogen dew point.The actual working state about the PEMFC stack can be simulated in the experiment plat.The hydrogen inlet pressure,air flow,coolant flow were adjusted for load change.The monitoring software was designed using LABVIEW software and communicated with main controller through Modbus TCP protocol.
Study of an energy monitoring and management center based on Labview

Lu Shuang,Wu Jing-yi

DOI: https://doi.org/10.3969/j.issn.1004-3950.2007.04.002

2007-01-01

Energy Engineering

Abstract:An energy monitoring and management center was primarily researched based on the Labview software of NI.The whole system of the center was divided into eight subsystems,by which all the functions of the energy monitoring and management center were accomplished,including high energy use efficiency among the whole process of energy production,transportation and consumption.At last,an interface designed with Labview was given.
On board data monitoring system for fuel cell vehicle

Zhen-hua Jin,Da-wei Gao,Qing-chun Lu,Dong-lin Yan

DOI: https://doi.org/10.3969/j.issn.1671-5497.2006.06.009

2006-01-01

Abstract:To meet the requirements of fuel cell vehicle data acquisition and monitoring, an on board data monitoring system was developed. The hardware is constructed with embedded PC, communication card and field bus data acquisition module. The monitoring software was developed by the embedded operating system XPE in the virtual instrument development platform. The fuel cell vehicle CAN bus and sensor channel data acquisition, data storage, information monitoring and malfunction alarm were realized by the developed system. The system provides a powerful tool for research and development of the fuel cell vehicle.
Control of fuel cell air supply system based on LPV model

Yeye SHEN,Xuelan CHEN,Lei XIE,Xiuliang LI,Yu WU,Lujun ZHAO

DOI: https://doi.org/10.3969/j.issn.0438-1157.2013.12.039

2013-01-01

Abstract:Proton exchange membrane(PEM) fuel cells are electrochemical devices that covert the chemical energy to electricity directly. This study was concentrated on the air supply system. This paper presented an improved four order fuel cell air supply system model, analyzing its constraints. And the linear parameter varying(LPV) model was proposed to deal with the non-linear characteristics of the dynamic model. To cope with the problem of immeasurable states, the Kalman filter was used to estimate the states and the output variables which should be measured were selected. Additionally, the state space model predictive control algorithm satisfying the constraints is designed based on LPV model to control the compressor voltage to ensure an adequate response to hydrogen fuel. Simulation results showed that model predictive controller based on LPV model is able to effectively control the fuel cell air system, and to meet the compressor surge and blocking boundary conditions and other constraints, Comparing with single model predictive control, better control performance was obtained with the proposed LPV-MPC. © All Rights Reserved.
System Control for PEMFC-Driving Robot Based on 32 Bit Microcontroller

LIU Cheng-ze,ZHU Xin-jian

DOI: https://doi.org/10.19708/j.ckjs.2006.06.013

2006-01-01

Abstract:Aiming at the energy problems confronted by the outdoor's robots,PEMFC-driving robot based on 32 bit microcontroller is designed.The control system can realtimely detect the status of fuel cell and the parameters of the robot body,and then corresponding control strategies are determined.The overall scheme is given and relative hardware design and software realization are also illustrated.
Implementation of Control System of Fuel Cell Powered Autonomous Robot

LIU Chengze,Xinjian Zhu

DOI: https://doi.org/10.3969/j.issn.1000-3428.2006.14.078

2006-01-01

Abstract:According to the power demand for the robot outdoors,the fuel cell powered robot based on 32 bit microcontroller is designed.With the control system oriented with the 32 bit embedded microcontroller,the power status of fuel cell and the status parameters of the robot body can be real-time inspected.Then the pose and power demand can be adjusted accordingly.The design of whole scheme is brought up and the hardware and software implementation is clarified.
Modeling and control of fuel cell systems and fuel processors

J. Pukrushpan

Abstract:MODELING AND CONTROL OF FUEL CELL SYSTEMS AND FUEL PROCESSORS by Jay Tawee Pukrushpan Co-Chairs: Anna Stefanopoulou and Huei Peng Fuel cell systems offer clean and efficient energy production and are currently under intensive development by several manufacturers for both stationary and mobile applications. The viability, efficiency, and robustness of this technology depend on understanding, predicting, and controlling the unique transient behavior of the fuel cell system. In this thesis, we employ phenomenological modeling and multivariable control techniques to provide fast and consistent system dynamic behavior. Moreover, a framework for analyzing and evaluating different control architectures and sensor sets is provided. Two fuel cell related control problems are investigated in this study, namely, the control of the cathode oxygen supply for a high-pressure direct hydrogen Fuel Cell System (FCS) and control of the anode hydrogen supply from a natural gas Fuel Processor System (FPS). System dynamic analysis and control design is carried out using model-based linear control approaches. A system level dynamic model suitable for each control problem is developed from physics-based component models. The transient behavior captured in the model includes flow characteristics, inertia dynamics, lumpedvolume manifold filling dynamics, time evolving spatially-homogeneous reactant pressure or mole fraction, membrane humidity, and the Catalytic Partial Oxidation (CPOX) reactor temperature. The goal of the FCS control problem is to effectively regulate the oxygen concentration in the cathode by quickly and accurately replenishing oxygen depleted during power generation. The features and limitations of different control configurations and the effect of various measurement on the control performance are examined. For example, an observability analysis suggests using the stack voltage measurement as feedback to the observer-based controller to improve the closed loop performance. The objective of the FPS control system is to regulate both the CPOX temperature and anode hydrogen concentration. Linear multivariable system analysis is used to identify the limitation of a decentralized controller and to design a model-based multivariable controller with significantly improved performance in CPOX temperature regulation. Further analysis unveils the critical controller cross-coupling term that contributes to the superior performance of the multivariable controller. c © Jay Tawee Pukrushpan 2003 All Rights Reserved

Engineering,Physics
Hydrogen consumption measurement research platform for fuel cell vehicles

MaoDong Fang,Mingjie Chen,Qingchun Lu,Zhenhua Jin

DOI: https://doi.org/10.1109/iCECE.2010.286

2010-01-01

Abstract:Hydrogen consumption measurement research platform is designed for fuel economy test of the proton exchange membrane fuel cell vehicle (PEM FCV). Hardware is constructed with industrial PC (IPC), field bus data acquisition module and device control module. RS485 field bus is selected for communication between the IPC and the modules. LabVIEW is used to develop the host computer management software. Several scheduled tests using this system verify that the platform meets the research requirement. © 2010 IEEE.
Modeling and Control of a Small Solar Fuel Cell Hybrid Energy System

Li Wei,Zhu Xin-jian,Cao Guang-yi

DOI: https://doi.org/10.1631/jzus.2007.a0734

2007-01-01

Abstract:This paper describes a solar photovoltaic fuel cell (PVEC) hybrid generation system consisting of a photovoltaic (PV) generator, a proton exchange membrane fuel cell (PEMFC), an electrolyser, a supercapacitor, a storage gas tank and power conditioning unit (PCU). The load is supplied from the PV generator with a fuel cell working in parallel. Excess PV energy when available is converted to hydrogen using an electrolyser for later use in the fuel cell. The individual mathematical model for each component is presented. Control strategy for the system is described. MATLAB/Simulink is used for the simulation of this highly nonlinear hybrid energy system. The simulation results are shown in the paper.

Fuel Cell Control System Based on LabVIEW

High temperature proton exchange membrane fuel cell hybrid power system monitoring platform designing

Design of a 5 Kw Distributed Grid-connected Fuel Cell Power System

Neutral Point Voltage Control For Three-Level Fuel Cell Power Conversion System

Design of Energy Management Control in Fuel Cell Power System

Monitor System of Energy-Feedback Electronic Load Based on CAN Bus and LabVIEW

Development of Simulation and Real Time Control Platform for Fuel Cell Powertrain

Design of PEMFC voltage monitor system based on USB

Automatic Code Generation for Fuel Cell Control System

A Distributed Real-Time Control System For Pem Fuel Cell Engine

Design of Monitoring System for Microgrid of Wind-Hydrogen-Fuel Cell Based on KingView Software

Development of Data Management Software for Fuel-cell Bus Demonstration Operation

Design and research of fuel cell experiment plat

Study of an energy monitoring and management center based on Labview

On board data monitoring system for fuel cell vehicle

Control of fuel cell air supply system based on LPV model

System Control for PEMFC-Driving Robot Based on 32 Bit Microcontroller

Implementation of Control System of Fuel Cell Powered Autonomous Robot

Modeling and control of fuel cell systems and fuel processors

Hydrogen consumption measurement research platform for fuel cell vehicles

Modeling and Control of a Small Solar Fuel Cell Hybrid Energy System