Abstract:Three-dimensional molecular dynamics simulations are conducted to investigate the effect of reciprocating nanomachining process on the subsurface damaged layers, surface integrity, cutting force, stress variation of subsurface, and changes of energy and defects in the workpiece. Results show that there is no obvious shear zone ahead the tool during nanomachining. Dislocation nucleations are near the free surface ahead the tool and the interface of the tool and the workpiece and propagate in the surface and downward in the workpiece. There are the generations of dislocation jog and dislocation loops ahead the tool during the reciprocating cutting. The values of the reciprocating cutting force for the (111) orientation and (100) orientation under offset distance of 0a(0) are not zero but 11.756 and 13.0498 nN, respectively. When the offset distance of the tool is up to 10a(0), the ratio of primary cutting force to reciprocating force is nearly 90%. The shape of the machined groove in the (111) orientation remains better than that in the (111) orientation in cases of both the primary cutting process and the reciprocating process. Reciprocating cutting with the offset distance of 5a(0) of the tool results in the pile-up atoms filling in the primary machined groove and forming the order lattice by surface reconstruction. Primary cutting force decreases with the reduction of workpiece sizes, which shows the size effects. With the increasing cutting depths, average primary cutting force and average reciprocating force increase. It is noted that reciprocating cutting force in the case of the (111) workpiece is larger than that of the (100) orientation except for the offset distance of 0a(0). With the increasing offset distance of the tool, the residual shear stress increases in the subsurface of the workpiece, and the order degree of subsurface atoms of the workpiece decreases in the cases of both the (111) orientation and (100) orientation. It is denoted that, with the offset distance at 5a(0), the peak of the average shear stress is highest during the reciprocating cutting. Meanwhile, the order degree of subsurface atoms in the case of the (111) orientation is better than that of the (100) orientation.

Molecular Dynamics Study of Groove Fabrication Process Using Afm-Based Nanometric Cutting Technique

Molecular Dynamics Simulation of Form Measurement Process of Soft Materials Using Atomic Force Microscope

AFM Tip-Based Fabrication of Silicon Nanostructures with Reduced Subsurface Amorphous Layers

An Experimental Investigation of Groove Control for Reducing Drag in a Flat Turbulent Boundary Layer

Molecular Dynamics Simulations of Ripple Nanostructure Formation During Nanomachining Via Atomic Force Microscopy

Molecular Dynamics Simulation of Multi-Groove Nano-Milling

Three Dimensional Molecular Dynamics Simulation of Nano-Lithography Process for Fabrication of Nanocomponents in Micro Electro Mechanical Systems (MEMS) Applications

Study of AFM-based Nanometric Cutting Process Using Molecular Dynamics

Molecular Dynamics and Experimental Study on Comparison Between Static and Dynamic Ploughing Lithography of Single Crystal Copper

Fabrication of Periodic Nanostructures Using AFM Tip-Based Nanomachining: Combining Groove and Material Pile-Up Topographies

Study of Effect of Impacting Direction on Abrasive Nanometric Cutting Process with Molecular Dynamics

Insight into Mechanics of AFM Tip-Based Nanomachining: Bending of Cantilevers and Machined Grooves

Fabrication of millimeter scale nanochannels using the AFM tip-based nanomachining method

Study on the Effects of the Machining Parameters on the Fabrication of Nanoscale Pits Using the Dynamic Plowing Lithography Approach

Cutting of Graphite at Atomic and Close-to-Atomic Scale Using Flexible Enhanced Molecular Dynamics

Micro-mechanical Analysis of Dynamic Processes of Nanomanipulation

Molecular Dynamics Simulation Study on the Influence of the Abrasive Flow Process on the Cutting of Iron-Carbon Alloys (α-Fe)

Molecular Dynamics Simulation of Nanomachining Process and Mechanical Properties of Nanostructure

Processing Outcomes of the AFM Probe-Based Machining Approach with Different Feed Directions

Three-Dimensional Molecular Dynamics Simulation of Nanostructure for Reciprocating Nanomachining Process

Molecular Dynamics Simulation of the Combination Effect of the Tip Inclination and Scratching Direction on Nanomachining of Single Crystal Silicon