Abstract:BaTiO3/Ni0.5Zn0.5Fe2O4 (BTO/NZFO) ceramic composite exhibit giant permittivity and high permeability simultaneously and could be potentially used in electronic devices. In this work, the sol-gel in situ derived 0.1BTO/0.9NZFO ceramic composites were sintered by conventional ceramic method and a modified three-step sintering process. In the new method, the ceramic composite was sintered initially at 1310 degrees C for 12 h, then sintered at 1325 degrees C for only 5 min, and ultimately cooled down rapidly within about 10 seconds. XRD, SEM and EDS were performed to analyze the phase composition, observe the morphology, and identify the elemental distribution of the ceramic composite. Results showed that the composite can be successfully formed through a carefully controlled step-sintering and rapid-cooling process. The composite exhibits a denser microstructure with larger grain size and increased density (by about 10%) compared with those prepared by conventional ceramic method. The effective permittivity of the newly-prepared composite is larger than 270k below 100 kHz, 3.5 times larger than that conventionally sintered at 1310 degrees C. A relatively low loss (similar to 0.3) was obtained at 30 kHz, 10.6% lower than conventionally prepared samples. The effective permeability reaches 150 (increased by 16.8%) with low magnetic loss (similar to 0.02). The three-step sintering method is a new effective way to break through the limitation of conventional sintering method and prepare ceramic composites with high density and thus enhanced dielectric and magnetic properties.

Enhancement of dielectric permittivity in the ZnO/PZT ceramic matrix nanocomposites

Morphology and Dielectric Properties of Lead Ziconate Titanate/Nano-ZnO Composite

Dielectric, magnetic and magnetoelectric properties of Ni0.5Zn0.5Fe2O4+Pb(Zr0.48Ti0.52)O3 composite ceramics

PREPARATION AND PROPERTIES OF BaTiO_3/Ni_(0.5)Zn_(0.5)Fe_2O_4 COMPOSITE CERAMICS

High Permittivity in Zr Doped NiO Ceramics

Enhancing Electrical Properties of High-Curie Temperature Piezoelectric Ceramics BNT-PZT and Their Mechanism

Formation and Electromagnetic Properties of 0.1 BTO/0.9NZFO Ceramic Composite with High Density Prepared by Three‐Step Sintering Method

Tunable Dielectric Behaviors of Magnetic Field of PZT5/NiFe2O4 Ceramic Particle Magnetoelectric Composites at Room Temperature

Coexistence of two phases in low-firing Pb(Zn1/3Nb2/3)O-3 composite ceramics and dielectric properties

Preparation of Nanosized Zno and Dielectric Properties of Composites Filled with Nanosized Zno

Effect of annealing temperature on the microstructure, dielectric, and microwave absorption performance of precursor blends derived ZrSiOCN ceramics

Effects of Sintering Behavior on Piezoelectric Properties of Porous Pzt Ceramics

Bi0.5Na0.5TiO3-BaTiO3-CaZrO3:ZnO High-Temperature Dielectric Composites with Wide Operational Range

In Situ TEM Observation on the Ferroelectric‐antiferroelectric Transition in Pb(Nb,Zr,Sn,Ti)O3/ZnO

Study on structure and dielectric properties of PbZnNbO based composite ceramics

Effect of Pb(Fe1/2Nb1/2)O3 modification on dielectric and piezoelectric properties of Pb(Mg1/3Nb2/3)O3–PbZr0.52Ti0.48O3 ceramics

In situ TEM observation on the ferroelectric‐antiferroelectric transition in Pb(Nb,Zr,Sn,Ti)O 3 /ZnO

Morphotropic phase boundary composition PNN-PZT ceramics and their outstanding electromechanical properties

Room temperature giant dielectric behavior of BaTiO3/Ni0.5Zn0.5Fe2O4 composite ceramic

Synchronous improvement of piezoelectric property and temperature stability in PSN-PMN-PT ceramics by forming composites with ZnO

Ferromagnetic properties of Ni0.2Cu0.2Zn 0.6Fe2O4-PZT composites