Abstract:In the field of material modeling, thermoplastic polymers are often studied because of their complex material behavior and their prevalence in industry applications due to their low cost and wide range of applications. Nowadays, where reusability becomes more and more important, materials which can undergo reversible thermomechanical deformations are appealing for, e.g., the construction of car body components. To predict such complex forming processes with multiple influencing factors, such as temperature, strain rate or underlying material morphology, model formulations are needed that account for these influences simultaneously and are validated against experimental data. Unfortunately, up to now only a few contributions are available which consider all these phenomena. In addition, the range of process parameters considered is often narrow due to the experimental effort required for testing. This usually results in limited predictive capabilities of the model. To overcome these limitations, in this work, a thermo-mechanically coupled material model is developed that accounts for the underlying morphology in terms of the degree of crystallinity (DOC). The model formulation is derived in a thermodynamically consistent manner, incorporating coupled nonlinear visco-elastic and elasto-plastic material behavior at finite strains. To characterize and further validate the model, mechanical as well as thermal experiments are conducted for polyamide 6 (PA6). Here, a blending strategy of PA6 together with an amorphous co-polymer is introduced during specimen production to achieve a wider range of stable DOCs(approximately 15%). The model formulation is successfully applied to experimental results and its predictions are in good agreement with experimental observations.

Rheo-optical Fourier-transform NIR Spectroscopy of Polyamide 11

The Assignment of Overtone and Combination Bands in the Near Infrared Spectrum of Polyamide 11

Anisotropic Optical Constants Of In-Plane Oriented Polyfluorene Thin Films On Rubbed Substrate

Two-dimensional correlation analysis of variable-temperature Fourier-transform mid- and near-infrared spectra of polyamide 11

In Situ Microscopic Infrared Imaging Study On Deformation-Induced Spatial Orientation And Phase Transition Distributions Of Pa12

Structure Analysis of Poly(N-Isopropylacrylamide) Using Near-Infrared Spectroscopy and Generalized Two-Dimensional Correlation Infrared Spectroscopy

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. Part Iii: Influence of Morphology on Molecular Orientation of Isotactic Polypropylene Films Subjected to Uniaxial Stretching

Two-dimensional Near-Infrared Correlation Temperature Studies of an Amorphous Polyamide

2d Ft-Nir And Ft-Ir Correlation Analysis Of Temperature-Induced Changes Of Nylon 12

Nanomechanics of Advanced Polymer Fibres

Segmental Orientations and Deformation Mechanism of Poly(Ether-Block-Amide) Films

Nanomechanics of Polyphenylacetylene Derivatives by AFM-based SMFS

Multimodal Non-Destructive In Situ Observation of Crystallinity Changes in High-Density Polyethylene Samples with Relation to Optical Parameters during Tensile Deformation

Two-Dimensional Correlation Analysis Of Variable-Temperature Fourier-Transform Near-Infrared Spectra Of An Amorphous Polyamide

The Structural Evolution and Mechanical Properties of Semi-Aromatic Polyamide 12T after Stretching

The Diffusion of Alcohols and Water in Polyamide 11: A Study by Fourier‐transform Near‐infrared Spectroscopy

A thermo-mechanically coupled constitutive model for semi-crystalline polymers at finite strains: Mechanical and thermal characterization of polyamide 6 blends

Study of self-heating and local strain rate in polyamide-6 and short fibre glass/polyamide-6 under tension through synchronised full-field strain and temperature measurements

The effect of stretching on polyamide – 6: assessment of crystallinity, mechanical properties, and surface roughness

Rheological Property Modification of a Molten-State Polyamide through the Addition of an α-Olefin–Maleic Anhydride Copolymer

The Methylene Infrared Vibration and Dielectric Behavior Monitored by Amide Group Arrangement for Long Chain Polyamides