Abstract:Bioactive apatite, such as hydroxyapatite ceramic (HA), [Ca10(PO4)6(OH)2] has been extensively investigated for biomedical applications due to its excellent biocompatibility and tissue bioactivity properties. Its bioactivity provides direct bonding to the bone tissue. Because of its similarity in chemical composition to the inorganic matrix of bone, HA is widely used as implant materials for bone. Unfortunately, because of its poor mechanical properties,. this bioactive material is not suitable for load bearing applications. In this study, by the assistance of dip-coating technique, HA coatings were deposited on titanium alloy substrates by employing hydrothermal derived HA powder. The produced coatings then were oven-dried at 130°C for 1 hour and calcined at various temperature over the range of 200-800°C for 1 hour. XRD measurement showed that HA was the only phase present in the coatings. However coatings calcined at 800°C comprised a mixture of HA and tri-calcium phosphate (TCP). FTIR measurement showed the existence of hydroxyl, phosphate, and carbonate bands. PO4 - band became sharper and narrower with the increased of calcination temperature. FESEM observation showed that the coating is polycrystalline with individual particles of nano to submicron size and has an average particle size of 35 nm. The thickness of the coating are direcly propotional with the viscosity of coating slurry. It was shown that the more viscous coating slurry would produce a thicker ceramic coating. Mechanical properties of the coating were measured in term of adhesion strength using a Micro Materials Nano Test microscratch testing machine. The result revealed that the coating had a good adhesion to the titanium alloy substrate.

Porous hydroxyapatite coating on strong ceramic substrate fabricated by low density slip coating-deposition and coating-substrate co-sintering

Preparation of hydroxyapatite coating on smooth implant surface by electrodeposition

Preparation of a High-Performance Porous Ceramic Membrane by a Two-Step Coating Method and One-Step Sintering

Hydroxyapatite-Based Coatings on Silicon Wafers and Printed Zirconia

Coating of hydroxyapatite on highly porous Al2O3 substrate for bone substitutes

Hierarchically Structured Ceramic Coatings Based on Zirconia and Magnesium Oxide with High Toughness

A new method to prepare hydroxyapatite coating of implants

Preparation and growth behaviours of low porosity hydroxyapatite with enhanced adhesion by electrochemical deposition on micro-arc oxide coatings

Preparation of Porous Hydroxyapatite-Zirconia Composite Scaffolds by Combination of Gel-Casting and Polymer Sponge Methods

[Hydroxyapatite bioactive coating on carbon/carbon composites]

Development of Bioactive Ceramic Coating on Titanium Alloy substrate for Biomedical Application Using Dip Coating Method

Interfacial characteristics of bioglass diffusion zone between scaffold-like hydroxyapatite/wollastonite coating and dense zirconia substrate

Annealing-temperature dependence of adhesion strength of hydroxyapatite layers coated on zirconia substrates by droplet elimination pulsed-laser deposition scheme

Fabrication of porous gehlenite coating on Al<sub>2</sub>O<sub>3</sub>-ZrO<sub>2</sub>-SiC composite ceramics and its <i>in vitro</i> biological activities

Recent advances in multifunctional hydroxyapatite coating by electrochemical deposition

Fabrication and properties of 3D printed zirconia scaffold coated with calcium silicate/hydroxyapatite

Hydroxyapatite Coating with Strong (002) Crystallographic Texture Deposited by Micro-Plasma Spraying

In-situ synthesis and characterization of calcium phosphate coatings on rapidly solidified zirconia toughened alumina eutectic bioceramics by laser cladding

Osteoconductivity and osteoinductivity of porous hydroxyapatite coatings deposited by liquid precursor plasma spraying: in vivo biological response study

Fabrication and properties of a stable and porous YSZ/nano-HA structure by binder jetting processes

In vitro bioactive behavior of hydroxylapatite-coated porous Al(2)O(3)