Abstract:Because they have the potential for ultra low NOx emissions and high efficiency, Homogeneous Charge Compression Ignition (HCCI) engines have the potential to develop a significant niche. However, a narrow operating range, (bracketed by severe knock and misfire problems), presents a formidable obstacle to developing usable HCCI combustion systems. HCCI combustion is influenced by a complex array of operating variables including fuel octane quality, intake preheating temperature, compression ratio, equivalence ratio, exhaust gas recirculation and engine component temperature. These variables affect the two critical combustion parameters: ignition timing and combustion duration. If these two parameters can be controlled by appropriate settings of the operating variables, a good HCCI combustion scheme could be achieved. Therefore, the theoretical prediction of these two combustion parameters as a function of the key operating variables is necessary for development of HCCI combustion. This paper describes a stand-alone, single-zone and multi-zone combustion model which have been developed for the specific purpose of investigating HCCI combustion control. In the multi-zone model, temperature and composition in each zone were adjusted in order to study the effect of in-homogeneity which is critical to understanding ignition timing and combustion duration in real HCCI engines. The models simulated HCCI combustion using two fuels: hydrogen, (11 species, 23 reactions- from CHEMKIN library), and natural gas, (53 species, 325 reactions- from GRI mech). The capabilities of the two models to predict ignition timing, combustion duration and peak pressure were verified against experimental and simulation results of Fiveland et al [2, 11]. The models were then used to study the effect of different in-homogeneity levels of equivalence ratio, intake temperature and residual fraction. The single zone model could only predict ignition timing while the multi-zone model shows the capability to mimic realistic HCCI combustion phenomena. The study showed that some degree of in-homogeneity is critical to predicting performance of the homogeneous charge compression ignition engine. Further, stratification of equivalence ratio was relatively ineffective at changing combustion while stratification of mixture temperature was very effective. Stratification of the residual fraction proved to be the most promising method of controlling combustion parameters and the mechanism was primarily thermal.

Simulation and Analysis of Hydrogen-fueled Engine Combustion

Combined experimental-numerical analysis of hydrogen as a combustion enhancer applied to wankel engine

Numerical Simulation of HCNG Engine on GT-Power

Modeling of Hydrogen Combustion from a 0D/1D Analysis to Complete 3D-CFD Engine Simulations

Development and Validation of a Quasi-Dimensional Combustion Model for SI Engines Fuelled by HCNG with Variable Hydrogen Fractions

Research on the Influence of Hydrogen and Oxygen Fuel Obtained from Water Electrolysis on Combustion Stability of Shale Gas Engines

Numerical investigation on gaseous fuel injection strategies on combustion characteristics and NO emission performance in a pure hydrogen engine

A Stand-Alone Multi-Zone Model for Combustion in HCCI Engines

Simulation Study on Combustion Performance of Ammonia-Hydrogen Fuel Engines

Comparison of Single-zone and Multi-zone Combustion Model for HCCI Engine

Computational Investigation of Combustion, Performance, and Emissions of a Diesel-Hydrogen Dual-Fuel Engine

Multi-dimensional Simulation Study of an HCNG Engine

Numerical Simulation of Gasoline Stratified Charge Compression Ignition Using 3D-CFD Coupled with Detailed Chemistry

Effect of excess hydrogen on hydrogen fueled internal combustion engine under full load

Two-zone Chemical Kinetics Modeling of a Gasoline HCCI Engine

Transient Modeling and Performance Analysis of Hydrogen-Fueled Aero Engines

Computational Study of Hydrogen Direct Injection for Internal Combustion Engines

Numerical Simulation of HCCI Engine with Multi-Stage Gasoline Direct Injection Using 3D-CFD with Detailed Chemistry

A computational study of direct injection gasoline HCCI engine with secondary injection

Computational study of hydrogen engine combustion strategies: Dual-Fuel compression ignition with Port- and Direct-Injection, Pre-Chamber Combustion, and Spark-Ignition

Modeling of HCCI combustion: From 0D to 3D