RESEARCH ON HYDRAULIC SYSTEM OF KZC-5 TYPE REAR DUMP TRUCK IN UNDERGROUND MINE

LEI Ze-yong

DOI: https://doi.org/10.3969/j.issn.1000-8063.2005.02.008

2005-01-01

Abstract:KZC-5 type rear dump truck in underground mine is introduced in this paper. The determining principles and ways of two main hydraulic systems are discussed. It has been proved that the hydraulic systems are reasonable in the industrial scale test.

What problem does this paper attempt to address?

RESEARCH ON TRACTIVE POWER OF KZC-5 REAR DUMP TRUCK IN UNDERGROUND MINE

雷泽勇

DOI: https://doi.org/10.3969/j.issn.1000-8063.2003.03.009

2003-01-01

Abstract:The tractive power of KZC-5 rear dump truck in underground mine is studied in this paper. The principles and ways of defining the power are discussed . It is proved that the power of KZC-5 rear dump truck in underground mine is reasonable in the industrial scale test.
Simulation Research of Parallel Hydraulic Hybrid Excavator

Zhang Minjie,Wang Qingjiu,Guan Cheng

2010-01-01

Abstract:Due to the power transmission structures of the traditional excavators, the relevant methods can not help the distribution of working points of the engine. So a hydraulic hybrid technology and its control scheme was proposed herein. The working conditions were analyzed and the structures of hydraulic hybrid excavator were introduced. A parallel hydraulic hybrid system was chosen for simulation. The load of an actual excavator was used as input of the system. The parallel hydraulic hybrid excavator demonstrates that it can stabilize the engine speed, increase the efficiency and optimize the drivability.
Energy saving scheme of hydraulic excavators based on hybrid power technology

Dong-yun WANG,Shuang-xia PAN,Xiao LIN,Cheng GUAN

2009-01-01

Abstract:To further improve fuel efficiency of hydraulic excavators, a new energy saving scheme which used the hybrid power source to replace the conventional single diesel engine was proposed. By analyzing the load condition of the hydraulic excavators and the distribution of the engine working point, the necessity and feasibility of hybrid technology for hydraulic excavators were revealed. Matlab/Simulink models of the two kinds of hybrid excavators were constructed which used the load data collected from a real 5 t excavator as the load input. The energy saving effect, system cost and power performance of the three kinds of power train systems were compared through simulation and experiments. Comparison results showed that the parallel configuration was the most suitable technology for hydraulic excavators energy saving. It could improve energy saving for hydraulic excavators.
Design and Control of Hydraulic Hybrid System for Excavators

Shizhen Li,Jianhua Wei,Jinhui Fang,Kai Guo,Wei Liu

DOI: https://doi.org/10.1115/fpmc2015-9564

2016-01-01

Abstract:This paper is to study on a novel recovery and release hydraulic hybrid system for excavators (HHE). The HHE uses hydraulic accumulators to recover the potential energy of the boom, the kinetic energy of the swing motor and the overflow hydraulic energy of the excavator’s main relief. The recovered energy is then utilized through a variable hydraulic motor as assistant power of the engine. The key issue of the HHE is that the operation of the boom must be similar to the conventional one about the sensing of the driver and the system must achieve higher efficiency and save more energy when comparing with the conventional system. In order to improve the recovery efficiency and while controlling the boom velocity with the similar operation, one design concept named “microcut” is proposed. When the boom drops down fast, a proportional valve is used to control the boom. While the boom goes down slowly, the recovery system is cut off. Then, the multi-way valve of the original system works to ensure good handling. An experimental prototype is designed and built in a 21-tons excavator. A 16% fuel-saving effect is obtained by weighing engine’s fuel consumption with the same amount of work, under conditions of the similar operation and higher efficiency compared with the conventional excavator.
Design and Experiment of Hydraulic Propelling System in Shields

胡国良,周新建,龚国芳,杨华勇

DOI: https://doi.org/10.3969/j.issn.1000-1212.2007.03.016

2007-01-01

Abstract:Shield is a kind of technology concentrated, large scale equipment dedicated in underground tunnel excavation that combines diversified technologies and subjects such as mechanics, electrics, hydraulics, measurement and control into one machine. Propelling system is the key system of a shield. It fulfills the thrusting operation of the shield and functions turning, curved traveling, posture controlling, direction correcting and synchronous movement. The hydraulic propelling system combining pressure control and flow control is designed using hydroelectric proportional control technology. Its work principle and system composition are expatiated in the article. Controls of thrust pressure and trust speed of the system is studied on shield simulation test bench. The test verified that the hydraulic propelling system developed could control thrust pressure and thrust speed in real time and meet the requirements of shield in different geological conditions.
Water Hydraulic Test Rig

H Zhou,Hy Yang,O Pohls

2001-01-01

Abstract:Water hydraulics is a new research area using filtered natural water or sea water as working medium in hydraulic systems instead of mineral oil with advantages of energy saving., fire resistance and no pollution. By the end of 1990s Zhejiang University decided to bring our state key laboratory to the very forefront of water hydraulics research by investing in a sophisticated and versatile test environment. The research objects, construction and control modes of the built Water Hydraulic Test Rig (WHTR) are introduced in this paper.
Hydraulic System Integration and Experimental Analysis of Shield Tunnelling Machine for Simulator Test Rig

Guoliang Hu,Guofang Gong,Huayong Yang,Tong Xing

DOI: https://doi.org/10.3969/j.issn.1000-1298.2005.12.028

2005-01-01

Abstract:Aiming at the design requirements of shield tunnelling machine for simulator test rig, hydraulic systems of shield were designed and manufactured by applying electro-hydraulic proportional control technology, which included thrust hydraulic system, screw conveyor hydraulic system and cutting wheel drive hydraulic system. Experimental analyses were also carried out. The experimental results showed that the designed hydraulic systems could meet the tunnelling requirements of shield at all kinds of geological conditions. The front earth pressure value could also be controlled in the range of set value by adjusting the advancing speed, screw conveyor revolving speed and cutting wheel revolving speed, which lead to reduce ground deformation.
Study on Dynamic Performance of EFMC System in Hydraulic Excavator

Wang Xiangbing,Tong Shuiguang,Ge Junxu,Zhang Jian

DOI: https://doi.org/10.3969/j.issn.1004-132x.2014.15.009

2014-01-01

Abstract:A virtual prototype of EFMC system in hydraulic excavator was constructed by analy-zing the control principle of EFMC system based on lastdruck unabh?ngige durch-fluss verteilung (LUDV)multi-way valve,the accuracy of flow matching was improved by adopting feedback closed-loop control method with real-time detection of oil cylinder speed signals.The dynamic and hydraulic models of EFMC system in hydraulic excavator were constructed respectively,and the co-simulation was conducted based on actual working conditions,the dynamic characteristics and energy-saving char-acteristics of mining operation process were studied,compared the experimental results with the tradi-tional LUDV load-sensing system,the results indicate that compared with the load-sensing system,the dynamic response characteristics and stability performance of the EFMC system are improved,and the pressure margin is reduced obviously,the energy efficiency is improved,also the dynamic response characteristics of feedback closed-loop control system are improved.Theoretical basis and reference are provided for further research on dynamic characteristics,energy-saving characteristics and stability performance in excavator.
Design and Experiment on the Control System of Electro-hydraulic Plow Depth of Tractor Hydraulic Hitch Mechanism

Qiaolian Du,Xicheng Xiong,Jianhua Wei

2008-01-01

Abstract:A tractor electro-hydraulic control system was designed and studied based on the plowing depth system's principle of tractor hydraulic hitch mechanism. An electro-hydraulic proportional valve was used as the master valve in this system. The mathematic model of the tractor electro-hydraulic control system was set up and then the characteristic of load control and position control was analyzed. Finally experimental research was performed. The experimental results showed that transient time of position regulation is 0.65 s, and its static error is 1.5 cm; the adjusting time of draft regulation is 7.5 s; the fluctuating scope is ±1 cm, when the plowing depth is 20 cm in draft and position regulation. This system could meet the challenge of plowing depth control system in formidable natural conditions, and the object of uniform plowing depth and work stability were achieved.
Selection Analysis of Large Excavator and Hydraulic Shovel in Mines

ZHANG Yong-ming

DOI: https://doi.org/10.3969/j.issn.1672-6413.2012.06.080

2012-01-01

Abstract:The large excavators and hydraulic shovels with dipper capability more than 20 m3 are the main mining equipments in open-pit mines.This article analyzes the characteristics and working conditions of large excavators and hydraulic shovels,to make users select them easily.
Research on Characteristics and Test of Hydraulic Driving System for Rubber Rig

Zhao Shengdun,Chen Fenglei,Wang Song

DOI: https://doi.org/10.1109/icacmve.2019.00052

2019-01-01

Abstract:The working environment of coal mine roadway has become more severe with the extension of the depth of coal mine roadway. Therefore, there is a higher demand for the size and performance of trackless rubber tire vehicles. The rubber wheel drilling rig developed in combination with the actual needs of coal mine roadway. Based on the detailed calculation and comparison of the two schemes, the applicable drive hydraulic system is proposed. On this basis, the advantages in use are analyzed. Through theoretical analysis, the key parameters affecting the differential and differential problems are proposed. The applicable solutions for the two coal mines are studied, and a more suitable scheme is selected through comparison. The static and dynamic test results show that the system has good operation performance and high efficiency under the condition of limited volume of the rubber drilling rig, which makes it have high passability and stability.
Research And Implementation Of Key Technology Of Braking Energy Recovery System For Off-Highway Dump Truck

Yang Wang,Junlin Chen,Jian Liu,Kui Liu,Yan Zhang,Jing Wu,Hua Zeng,Zeng-Lun Guan

DOI: https://doi.org/10.1109/IECON.2017.8216669

2017-01-01

Abstract:Off-highway dump truck contains amounts of potential energy and kinetic energy. During the braking process, these two parts are consumed in the form of heat on the braking resistance, and the energy consumption will be about 24 percent of total energy consumption of the Truck. Hence, it is necessary to recover the braking energy. This paper, aiming at the characteristics of electric drive system in off-highway dump truck, proposes a new type of DC/DC main circuit which is a series connection topology that includes super-capacitor and battery hybrid energy storage, the DC bus's rate voltage is 1800v. The bottom controller is designed based on DSP + FPGA, which realizes the efficient control and protection of the system, and completes the recovery and utilization function of the braking energy in off-highway dump trucks. In the host computer, the monitoring system designed by utilizing of C#. net language, and the relay protection 103 communication protocol has been used to improve system stability. In this paper, the dynamic test platform of braking energy recovery system has been completed, after the dynamic test, the system has been install in Komatsu 730E dump truck of Pingshuo Anjialing surface coal mine to complete the field operation. The experimental result shows the effectiveness and reliability of the system.
Development and application of the mine crawler sump cleaning machine

ZOU Fenglou,SONG Deyu,Li Qiang,Wu Ruiming

2009-01-01

Abstract:It is important for the mine safety in production cleaning sumps periodically. So, based on its difficult points and shortcomings at the moment, the paper introduces the structure and compositions of the developed cleaning machine, its working principle and the lectotype and design of the key parts and components. Finally, the present debugging and experiment show the machine has advantages of good utility, remarkable economic profit and wide application prospect.
Driven System and Characteristics Research of Large Hydraulic Shovel Swing Motion

ZHAO Bin,QUAN Long,HUANG Jiahai,CHENG Hang,LI Guang,ZHANG Yongming

DOI: https://doi.org/10.3901/jme.2017.06.176

2017-01-01

Journal of Mechanical Engineering

Abstract:Mining hydraulic shovel is one of widely used equipment in open-pit mining and large engineering construction.However,the shovels used in domestic are always dependent on importation.In 2008,Taiyuan Heavy industry started to research and development the first domestic mining hydraulic shovel whose weight is 260 t and capacity of the bucket is 15 m3.Swing motion is the most frequent movement of mining excavator and each operating cycle includes two times of acceleration and deceleration.If the swing circuit can't be designed will,that will cause serious heating of system and impact the working efficiency of the machine.In order to shorten design period and comprehend the working performance before the construction of the real system,the advantages and disadvantages of open circuit and closed circuit are analyzed to determine the specifications and parameters of hydraulic components.The mechanical dynamic simulation software ADAMS and mechatronic system simulation software AMESim are used to build the co-simulation model of whole designed mining hydraulic shovel.During the working process of mining excavator,the operation performance and energy efficiency characteristic of the two circuit are simulated,a method that using electro hydraulic proportional controlled double closed circuits for swing control driven in parallel way is determined.An electro-hydraulic proportional pump.is used to control the rotary motor directly,which can avoid the throttling loss of valve controlled system.Meanwhile,in order to simplify the circuit,the hydraulic shovel own pilot pump is used to realize the compensating of closed circuit.The influence of rotary inertia's large range variety on the rotation characteristic is further simulated and researched,the relationship between the time acceleration and deceleration and swing angle.The whole electro-hydraulic swing system is designed and applied the designed mining hydraulic shovel.Field tests and trial run tests indicate that the designed electro hydraulic proportional controlled double swing closed circuits can smoothly control the upper car acceleration and deceleration under the condition of large range variety of rotary inertia,the heating is small and the shovel can work continuous for a long time.
Study on Design of Working Device and Hydraulic System of Hydraulic Excavator Based on Computer Aided Technology

WenJing Hu,Zheng Meng

DOI: https://doi.org/10.1088/1742-6596/1574/1/012028

2020-06-01

Journal of Physics: Conference Series

Abstract:Abstract This paper expounds the importance of hydraulic excavators in urbanization and infrastructure construction, and reviews the history of the emergence and development of hydraulic excavators.Based on the computer aided technology and the working process of the hydraulic system in the practical application, the paper expounds the principles to be followed in the design, so as to realize the design and research of the working device and the hydraulic system of the excavator.
Virtual prototype and field test study on hydraulic brake system performance of mining truck

Xiaobin Fan,Jing Gan

DOI: https://doi.org/10.1177/1464419318785394

2018-07-03

Abstract:In order to study the braking performance of mining dump truck, the modeling of the oil–gas suspension, front and rear brake of the dump truck were carried out first. Then the virtual prototype model of the dump truck was established in multibody dynamic simulation software. The simulation of braking and emergency braking performance, brake deviation on the flat road, and 9% downhill road were carried out. The brake in driving performance, emergency brake performance, disc brake retardance performance, transmission retardance performance, and hydraulic braking system response time were carried out by the real vehicle experiment, respectively. The result shows that the clearance elimination and pressure rise time of braking system are slightly long, especially the clearance elimination time, so the oil system should have an improvement. At the same time, the braking force distribution of the front and the rear is not reasonable, and the front wheel braking torque is slightly insufficient. After solving these problems by authors’ project team, the braking performance of the mine dump truck has been improved significantly.
Research and design of excavation face remote reproduction and remote control systems

C. Liu,J. G. Jiang,W. H. Qu,Z. Z. Zhou,J. J. Li,H. Liu,S. Ye,S. Y. Yao

DOI: https://doi.org/10.1201/9781315212876-60

2017-01-01

Abstract:This paper referred to the National Key Basic Research Program of China (grant no. 2014CB046306), Key Fundamental Research on the Unmanned Mining Equipment in Deep Dangerous Coal Bed, as the topic background and showed the unmanned fully mechanized excavation face for deep coal seam proposed for higher requirements related to efficiency, automation, and intelligentization of the roadheader. Research and development on fully mechanized excavation face remote reproduction and remote control systems is discussed in this paper. The systems comprise the airborne control system, the industrial supervisory control computer, the Linux operating systems and the CAN bus communication. By the optical fiber and the airborne computer, the supervisory control software platform is used to transmit data and control remotely the openness of signals for the roadheader; thus, it has extensive application prospect, which provides technical support for unmanned excavation equipment, which really achieve development of fully mechanized excavation face machinery aimed at the direction of upsizing, intelligentization, and unmanned property.
Application of Hydraulic Transmission for Mine Underground Trackless Haulage Vehicle

Liu Chun

Abstract:In recent years,hydraulic transmission has been applied on nearly all the travel mechanisms of the ground engineering vehicles.An analysis to the wide application of the hydraulic transmission for mine underground trackless haulage vehicle is given.The Latest development of the transmission system on WC40 shield carrier by author's institute is described as well.

Environmental Science,Engineering
Underground Backfilling Technology for Waste Dump Disposal in Coal Mining District

Huang Yanli,Zhang Jixiong,Liu Zhan,Zhang Qiang

DOI: https://doi.org/10.1109/ICDMA.2010.450

2010-01-01

Abstract:China is one of the few countries over the world which uses coal as the main energy, and its coal production has become more than one third of the world. To cope with the serious problems caused by the coal exploitation such as waste discharge, environment destruction and land occupation, harmonious development of coal mines green exploitation and ecological environment has been suggested by Chinese scholars. This paper systematically introduces the general framework of underground backfilling technology for waste dumps disposal. The surface waste crushing and conveyance system, deep vertical feeding system used to convey waste from surface to underground, underground conveyance system, backfilling system layout of fully mechanized long wall mining with solid material backfilling technology, key equipment and backfill technics were researched and developed. The engineering application indicates: using the fully mechanized mining with solid material backfilling technology can dispose waste 30,000 to 50,000 tons while exploit coal 50,000 to 80,000 tons per month, so that a higher production, more effective recovery and environmental benefits will be realized.
Mine Dump Truck Braking Performance Test and Simulation

Xia Qun-sheng

2009-01-01

Abstract:The braking system of a mine dump truck was theoretical and experimental researched,and braking power and distribution coefficient were optimized.It shows that the actual braking force and allocation is close to optimal value,but the system response time is too long.The virtual prototype model was established,the brake deviation and brake side slipping were simulated.The results showed that the lateral stiffness has significant impact on brake deviation.When the rear axle was lock,the dump truck was instability.

RESEARCH ON HYDRAULIC SYSTEM OF KZC-5 TYPE REAR DUMP TRUCK IN UNDERGROUND MINE

RESEARCH ON TRACTIVE POWER OF KZC-5 REAR DUMP TRUCK IN UNDERGROUND MINE

Simulation Research of Parallel Hydraulic Hybrid Excavator

Energy saving scheme of hydraulic excavators based on hybrid power technology

Design and Control of Hydraulic Hybrid System for Excavators

Design and Experiment of Hydraulic Propelling System in Shields

Water Hydraulic Test Rig

Hydraulic System Integration and Experimental Analysis of Shield Tunnelling Machine for Simulator Test Rig

Study on Dynamic Performance of EFMC System in Hydraulic Excavator

Design and Experiment on the Control System of Electro-hydraulic Plow Depth of Tractor Hydraulic Hitch Mechanism

Selection Analysis of Large Excavator and Hydraulic Shovel in Mines

Research on Characteristics and Test of Hydraulic Driving System for Rubber Rig

Research And Implementation Of Key Technology Of Braking Energy Recovery System For Off-Highway Dump Truck

Development and application of the mine crawler sump cleaning machine

Driven System and Characteristics Research of Large Hydraulic Shovel Swing Motion

Study on Design of Working Device and Hydraulic System of Hydraulic Excavator Based on Computer Aided Technology

Virtual prototype and field test study on hydraulic brake system performance of mining truck

Research and design of excavation face remote reproduction and remote control systems

Application of Hydraulic Transmission for Mine Underground Trackless Haulage Vehicle

Underground Backfilling Technology for Waste Dump Disposal in Coal Mining District

Mine Dump Truck Braking Performance Test and Simulation