Selection Analysis of Large Excavator and Hydraulic Shovel in Mines

ZHANG Yong-ming

DOI: https://doi.org/10.3969/j.issn.1672-6413.2012.06.080

2012-01-01

Abstract:The large excavators and hydraulic shovels with dipper capability more than 20 m3 are the main mining equipments in open-pit mines.This article analyzes the characteristics and working conditions of large excavators and hydraulic shovels,to make users select them easily.

What problem does this paper attempt to address?

Simulation Research of Parallel Hydraulic Hybrid Excavator

Zhang Minjie,Wang Qingjiu,Guan Cheng

2010-01-01

Abstract:Due to the power transmission structures of the traditional excavators, the relevant methods can not help the distribution of working points of the engine. So a hydraulic hybrid technology and its control scheme was proposed herein. The working conditions were analyzed and the structures of hydraulic hybrid excavator were introduced. A parallel hydraulic hybrid system was chosen for simulation. The load of an actual excavator was used as input of the system. The parallel hydraulic hybrid excavator demonstrates that it can stabilize the engine speed, increase the efficiency and optimize the drivability.
Dynamic Characteristic of Power Source in Parallel Hybrid Hydraulic Excavator

林潇,管成,潘双夏,王冬云

DOI: https://doi.org/10.3785/j.issn.1008-973x.2010.02.026

2010-01-01

Abstract:The working condition property of the hydraulic excavator was analyzed based on the 15 second typical operating cycle.The mathematical model of power source in parallel hybrid hydraulic excavator was established.An optimal set of power source parameters in parallel hybrid hydraulic excavator was pro-posed.Then the generator/motor efficiencies of the space vector pulse width modulation(SVPWM)-con-trolled permanent magnet synchronous motor(PMSM)and the charge/discharge efficiencies of the NiMH battery were analyzed under the same circumstance as well as the dynamic response characteristic including motor speed,motor torque and battery SOC.Simulation results show that the optimal set of power source in powertrain can satisfy the requirement of power and energy transformation efficiency for hydraulic exca-vator,and help achieve better fuel consumption with hybrid configuration.Furthermore the battery system was only treated as a media to transform energy.The more energy-saving and higher efficient control for the hydraulic excavator was achieved.
Air Conditioning and Selection of Large Mining Excavator Cab

Long Zhang,Hui-long Sun,Yong-ming Zhang,Xiao-ming Wang

DOI: https://doi.org/10.3969/j.issn.1674-9146.2014.07.091

2014-01-01

Abstract:This essay introduces the present situation of the use of large mining excavator cab air conditioning, the selection of air conditioning design are analyzed, according to the structural characteristics of large mining excavator is too heavy for the air-conditioning layout, and the air of a selection of design.
Driven System and Characteristics Research of Large Hydraulic Shovel Swing Motion

ZHAO Bin,QUAN Long,HUANG Jiahai,CHENG Hang,LI Guang,ZHANG Yongming

DOI: https://doi.org/10.3901/jme.2017.06.176

2017-01-01

Journal of Mechanical Engineering

Abstract:Mining hydraulic shovel is one of widely used equipment in open-pit mining and large engineering construction.However,the shovels used in domestic are always dependent on importation.In 2008,Taiyuan Heavy industry started to research and development the first domestic mining hydraulic shovel whose weight is 260 t and capacity of the bucket is 15 m3.Swing motion is the most frequent movement of mining excavator and each operating cycle includes two times of acceleration and deceleration.If the swing circuit can't be designed will,that will cause serious heating of system and impact the working efficiency of the machine.In order to shorten design period and comprehend the working performance before the construction of the real system,the advantages and disadvantages of open circuit and closed circuit are analyzed to determine the specifications and parameters of hydraulic components.The mechanical dynamic simulation software ADAMS and mechatronic system simulation software AMESim are used to build the co-simulation model of whole designed mining hydraulic shovel.During the working process of mining excavator,the operation performance and energy efficiency characteristic of the two circuit are simulated,a method that using electro hydraulic proportional controlled double closed circuits for swing control driven in parallel way is determined.An electro-hydraulic proportional pump.is used to control the rotary motor directly,which can avoid the throttling loss of valve controlled system.Meanwhile,in order to simplify the circuit,the hydraulic shovel own pilot pump is used to realize the compensating of closed circuit.The influence of rotary inertia's large range variety on the rotation characteristic is further simulated and researched,the relationship between the time acceleration and deceleration and swing angle.The whole electro-hydraulic swing system is designed and applied the designed mining hydraulic shovel.Field tests and trial run tests indicate that the designed electro hydraulic proportional controlled double swing closed circuits can smoothly control the upper car acceleration and deceleration under the condition of large range variety of rotary inertia,the heating is small and the shovel can work continuous for a long time.
Performance analysis of hydraulic excavators in complex excavation environments and different bucket trajectories

Bowen Liu,Zongyan Zhou,Jieqing Gan,Dean Ellis,Ruiping Zou,Aibing Yu

DOI: https://doi.org/10.1016/j.powtec.2024.119539

IF: 5.64

2024-02-18

Powder Technology

Abstract:Simulations of excavation operations not only help understand how excavators perform in specific environments but also can be used to optimise operating parameters. In this work, we explore the performance of hydraulic excavators under conditions of cohesive and size-dispersed materials and different bucket trajectories. The results indicate that with the cohesion increasing, the spillage of particles from the bucket is reduced, but the hydraulic power fluctuates greatly due to the strong collision of particle aggregates on the bucket. As the particle size distribution turns wider, small particles exert an intensive interaction force on the bucket, and the stress distribution on the bucket becomes wider. Therefore, some suggestions are given for practical excavation operations in different stockpile scenarios. Additionally, the bucket can be initially placed close to the base of the stockpile to achieve low specific energy consumption and high productivity.

engineering, chemical
Research on the matching characteristics of the theoretical digging force of a backhoe hydraulic excavator

Zhigui Ren,Jiahao Li,Xiaoping Pang,Jurong Liu,Tianyu Li,Songsong Yu

DOI: https://doi.org/10.1038/s41598-022-19976-x

IF: 4.6

2022-09-30

Scientific Reports

Abstract:The theoretical digging force is the maximum digging resistance that an excavator can overcome, which is an important measure of its digging capacity. To study the matching of the digging capacity with the actual demand and the matching of the working device mechanism, a 36.5 t backhoe hydraulic excavator is used as an example to analyse the distributions of the digging resistance under two different normal digging area working conditions and the maximum digging resistance characteristics of the tool. An appropriate digging postures are selected, based on limit digging force and compound digging force models, the theoretical digging forces under the two working conditions are obtained and matched with the measured digging resistance force values and the limiting factors affecting the digging force. The results show that the average percentage of theoretical digging forces greater than the measured digging resistance under both calculation models is 84.06% rather than 100%. The results of different digging methods all indicate that small chamber locking of the boom cylinder is too often the limiting factor for the digging force, resulting in poor matching of the working device. This study provides guidance for the improvement of the theoretical digging force model and the evaluation of the matching characteristics of the working device.

multidisciplinary sciences
RESEARCH ON HYDRAULIC SYSTEM OF KZC-5 TYPE REAR DUMP TRUCK IN UNDERGROUND MINE

LEI Ze-yong

DOI: https://doi.org/10.3969/j.issn.1000-8063.2005.02.008

2005-01-01

Abstract:KZC-5 type rear dump truck in underground mine is introduced in this paper. The determining principles and ways of two main hydraulic systems are discussed. It has been proved that the hydraulic systems are reasonable in the industrial scale test.
Strategy for Determining Analysis Working Conditions of Hydraulic Excavator

Qingying Qiu,Zhenkai Wei,Bing Li,Yu Gao,Peien Feng,Jian Wu,Xiaoqing Wang

DOI: https://doi.org/10.4028/www.scientific.net/amr.838-841.487

2013-01-01

Advanced Materials Research

Abstract:It was incomplete and may have missed some dangerous working conditions to select several typical working conditions only in traditional strength analysis of hydraulic excavator. Therefore, the paper proposes a strategy that takes the working conditions when the load at each hinge of working device reaches largest into account. The working device of a 21t hydraulic excavator was analyzed with finite element analysis method when comparing these working conditions with the traditional typical ones. The results come out that the largest stress of boom, arm and bucket under these conditions increased respectively by 4.6%, 5.6% and 19.1% compared with the traditional most dangerous conditions. Consequently, in addition to the traditional typical conditions, it will be more safe and reliable to analyze the strength with the largest hinge loads conditions.
Reliability Analysis of Deep Excavation Based on Field Monitoring Data

ZHU Hong-hu,YE Xiao-wei,RAN Long

DOI: https://doi.org/10.3969/j.issn.1006-2106.2011.09.002

2011-01-01

Abstract:Research purposes: There are considerable uncertainties existing in deep excavation activities and the field monitoring data cannot directly reflect the present excavation stability condition in most cases.In this paper,combing Bayesian updating with Monte Carlo finite element method,real-time reliability assessment of stability during the excavation of Pengbu station of Hangzhou Metro is performed based on field measurement data. Research conclusions: The results show that,in comparison with conventional method,it is more rational to estimate the failure probability of deep excavation by use of field monitoring data.This method can effectively enhance the accuracy of excavation stability analysis and avoid the problems resulting from the errors of the inclinometer readings.The horizontal displacement monitoring data of the diaphragm wall can be used as the input information of reliability analysis.The selection of failure criteria has a significant influence on the stability analysis results.The proposed method can compensate for the limitations of conventional reliability analysis and is a promising alternative method for stability analysis of excavation based on field monitoring data.
Kinematics and Dynamics Analyzing of the WYD390 Working Device

HAN Shuai,LI Ai-feng,LI Hong,LI Guang

DOI: https://doi.org/10.3969/j.issn.1003-773X.2012.05.028

2012-01-01

Abstract:With the advantages of compact structure,convenient operation,flexible movement and easy maintenance,hydraulic excavator has been a very wide range of applications in large-scale mine at home and abroad. The working device that Taiyuan Heavy Industry independent research and development of China's first 400-ton mine hydraulic excavator has been analyzed about kinematics and dynamics. So it provides theoretical reference for the product optimization design and future product development.
Load Law Analysis and Fatigue Life Prediction for Bucket Teeth of Excavator Working Device

Yuyuan Long,Liman Yang,Yunhua Li

DOI: https://doi.org/10.1109/iciea54703.2022.10006102

2022-12-16

Abstract:The increasing demand for major infrastructure construction and large open-pit coal mines in China has driven the rapid development of large mining excavator. At present, the research is not completely figured out the change law of the external load and the degradation law of the working performance of the working device of the mining excavator during operation. Therefore, this paper intends to carry out research on the common basic scientific problems of performance degradation of super-large mining excavator working devices. A simplified model of the working device of the mining excavator is constructed, and the force analysis of the bucket mechanism is carried out. Then using EDEM discrete element simulation method to explore the time-domain and frequency-domain rules of the working load of the mining excavator working device under typical working conditions. On the basis of the load data, combined with the Palmgren-Miner fatigue cumulative damage theory, the fatigue life law of the mining excavator working device under typical working conditions is explored by using the method of COMSOL finite element simulation. The load law and fatigue life law of bucket teeth obtained in this study provide a valuable theoretical basis and a new research idea for the study of fault identification.

Environmental Science,Engineering
Study and Engineering Realization of Power Transmission System for Large Excavators

Ji Kai,Xu Ming,Qian Li,Gao Yue,Chen Jiafu

DOI: https://doi.org/10.3969/j.issn.1003-4862.2010.06.011

2010-01-01

Abstract:In this paper,it is discussed that the engineering method for realizing the technologic control of large excavators with power transmission.The key techniques are studied in great depth and applied to engineering practice,such as non-loop-current control,locked-rotor characteristics,the optimization of double-loop regulation,load balancing,vibration reducing shock,and over-current protection.And the imported analog system is upgraded with digital scheme.The realization has the excellent effect in the copper mine of DeXin' operation.
Decision Analysis on Disposal of Large Quantities of Excavated Soft Soil in Abandoned Mines Using a Bayesian Network

Linbo Wu,Liangtong Zhan,Shuai Zhang,Xue Song,Junyao Lu,Yong Wang

DOI: https://doi.org/10.1080/17480930.2022.2059868

2022-01-01

Abstract:Disposal of the excess excavated soft soils produced in construction is a contemporary engineering challenge. A win-win solution could be found through utilising much excavated soil during reclamation of abandoned mines, and an evaluation model is necessary to realise this solution. This study aimed to propose a decision-making framework for large-scale disposal of excavated soft soil during mine reclamation using a Bayesian network (BN). Utilising multi-facet information, a decision-making path considering engineering and economic factors, and engineering risks was established. Thereafter, the practicability of backfilling much excavated soft soil into 215 abandoned opencast mines located in Wenzhou, China was evaluated. Based on the decision-making path and information of the 215 mines, a BN including 22 nodes was established with the practicability of large-scale soil disposal in mines as the decision node. Consequently, 40 valid mines were evaluated to be able to absorb 5 x 10(7) m(3) soil, around 50% of the total excavated soil from the municipal districts of Wenzhou during 2020-2024. The BN evaluation showed high reliability with accuracy of all the nodes >70% and that of the decision node >90%. Five input nodes were identified to be high-impact for evaluation of the practicability and total fill volume.
Dynamics Simulation Analysis of Small-scale Mining Full Hydraulic Wheel Loader Based-on ADAMS in Symmetrical Load Condition

CHAI Guang-yuan,LI Ming,ZHAO Zhen,ZHANG Yi-fei

DOI: https://doi.org/10.13436/j.mkjx.2013.03.114

2013-01-01

Abstract:Three-dimensional solid model of full hydraulic wheel loader is established in Pro/E environment and then imported in ADAMS to carry out dynamic simulation and check whether there are interferences in the course of the movement,at the same time get the corresponding kinetics curves of the key hinge points in symmetrical load condition.The analysis results provide a reference for structural design of wheel loader and optimizing.
Research on the method of determining the block size for an open-pit mine integrating mining parameters and shovel-truck's operation efficiency

Weiqiang Guo,Guangwei Liu,Jiaming Li,Senlin Chai,Shupeng Guo

DOI: https://doi.org/10.1038/s41598-024-52815-9

IF: 4.6

2024-05-04

Scientific Reports

Abstract:The production plan of an open-pit mine depends on the block model, so it's crucial to determine the appropriate method and size for partitioning it. This study proposes a new method based on a closed shell three-dimensional geological model for determining block model size in open-pit mines. Instead of using regular block models, the shell model is directly cut, and the discrete geological body is referred to as the "mining model." Mining parameters and the shovel-truck's performance are integrated into the method. Bench height determines the Z-axis size, bench slope angle determines the inclination angle, and shovel width determines the X-axis size of the block model. The operation efficiency of the shovel-truck considers the probability distribution of simultaneous operations, allowing the determination of the Y-axis size of block models for different types of shovels. The developed "Mining Model" module in the software "Life Cycle Mining System" is used for practical implementation. By comparing the results with traditional block models, the superiority of the proposed method is demonstrated. This study provides a more accurate model for optimizing the production plan of open-pit mines throughout their life cycle.

multidisciplinary sciences
Improvement of Large Mining Shovels Cable Reel Device

Yu-ming Xu,Xiao-ming Wang,Yong-ming Zhang

DOI: https://doi.org/10.3969/j.issn.1674-9146.2014.09.057

2014-01-01

Abstract:Summary by the use of large mining excavator cable reel and appear on the scene, analysis the cable reel of min-ing electric rope shovel. This essay seeks a reasonable improvement program, which the cable reel device reasonably re-tractable external cable and ensure the using requirements of electric rope shovel.
Development and application of the mine crawler sump cleaning machine

ZOU Fenglou,SONG Deyu,Li Qiang,Wu Ruiming

2009-01-01

Abstract:It is important for the mine safety in production cleaning sumps periodically. So, based on its difficult points and shortcomings at the moment, the paper introduces the structure and compositions of the developed cleaning machine, its working principle and the lectotype and design of the key parts and components. Finally, the present debugging and experiment show the machine has advantages of good utility, remarkable economic profit and wide application prospect.
Research of Fully Automatic Coal Mining Combine System

Li Yin

2012-01-01

Abstract:The article focuses on analysis of shearer ranging arm loading,low waste of conveyor power and automatic mining craft process,and put forward new ideas of shallow web depth,low power waste and high automation craft level.Sany heavy equipment company developed fully automatic coal mining combine,which will change traditional ideas and methods of whole-set equipment design and selection.The main features of fully automatic coal combine will be compared with traditional equipments in end of article.
Plateau-type Large Mining Electric Rope Shovel

Long ZHANG,Bao-jian MAO,Yong-ming ZHANG,Zheng-jie LEI,Yong-peng WANG

DOI: https://doi.org/10.3969/j.issn.1672-6413.2017.03.036

2017-01-01

Abstract:Standard mining electric rope shovel is only applicable to the area below 2 000 meters above sea level.In order to adapt to the special climate in high altitude area, according to the design features of the standard mining electric rope shovel,we developed a plateau-type large mining rope shovel through improving the electrical insulation strength, increasing cab pressurization oxygen function and increasing air volume of ventilation fan, etc;.
Impact analysis of bucket capacity and boom length of mining excavators on hoisting mechanism life

Sergey Kuvshinkin,Polina Ivanova

DOI: https://doi.org/10.1051/e3sconf/202132600032

2021-01-01

E3S Web of Conferences

Abstract:The presented article considers the influence of the design parameters of the work equipment being the boom length and bucket capacity on the operating life of the hoisting mechanism of a mining excavator. The expediency of using replaceable working equipment at mining enterprises operating quarry excavators with an unchanged basic model of the machine is justified. A significant influence of the boom length, the handle length, and the bucket capacity of a quarry excavator are noted not only on the power, energy, and operational performance of the machine but also on the static and dynamic components of the load and the resource of the main drives. It has been established that an increase in the boom length does not lead to a decrease in the operating life of the hoisting mechanism. Moreover, the predominance of high-frequency components in the external load spectrum can lead to its increase. Increasing the bucket capacity at the maximum filling factor leads to the decrease in operating life.

Selection Analysis of Large Excavator and Hydraulic Shovel in Mines

Simulation Research of Parallel Hydraulic Hybrid Excavator

Dynamic Characteristic of Power Source in Parallel Hybrid Hydraulic Excavator

Air Conditioning and Selection of Large Mining Excavator Cab

Driven System and Characteristics Research of Large Hydraulic Shovel Swing Motion

Performance analysis of hydraulic excavators in complex excavation environments and different bucket trajectories

Research on the matching characteristics of the theoretical digging force of a backhoe hydraulic excavator

RESEARCH ON HYDRAULIC SYSTEM OF KZC-5 TYPE REAR DUMP TRUCK IN UNDERGROUND MINE

Strategy for Determining Analysis Working Conditions of Hydraulic Excavator

Reliability Analysis of Deep Excavation Based on Field Monitoring Data

Kinematics and Dynamics Analyzing of the WYD390 Working Device

Load Law Analysis and Fatigue Life Prediction for Bucket Teeth of Excavator Working Device

Study and Engineering Realization of Power Transmission System for Large Excavators

Decision Analysis on Disposal of Large Quantities of Excavated Soft Soil in Abandoned Mines Using a Bayesian Network

Dynamics Simulation Analysis of Small-scale Mining Full Hydraulic Wheel Loader Based-on ADAMS in Symmetrical Load Condition

Research on the method of determining the block size for an open-pit mine integrating mining parameters and shovel-truck's operation efficiency

Improvement of Large Mining Shovels Cable Reel Device

Development and application of the mine crawler sump cleaning machine

Research of Fully Automatic Coal Mining Combine System

Plateau-type Large Mining Electric Rope Shovel

Impact analysis of bucket capacity and boom length of mining excavators on hoisting mechanism life