Abstract:Polymer-fluid interfaces are used widely in a variety of applications, including separations, which require exposure of the polymer to dynamic flow conditions. Despite the ubiquity of such interfaces, the importance of convective mass transport within the near-interface region of a polymer is a fundamental process that is still poorly defined. As a step toward better defining mass transport behavior within the near-interface portion of a polymer, in this work, a new application of a spectroscopic method based on the combination of Forster resonance energy transfer (FRET) and total internal reflectance fluorescence microscopy (TIRFM) is reported that allows quantification of the penetration depth of a laminar flow field (i.e., the slip length) in a densely grafted, thin poly(N-isopropylacrylamide) (pNIPAM) film as a model polymer system. Specifically, decay curves from FRET of an acceptor with a donor attached at the substrate surface are fit to a combined Taylor-Aris-Fickian mass transport model to extract apparent linear diffusion coefficients of acceptor molecules for different flow rates. Apparent diffusion coefficients range from 1.9 x 10(-12) to 9.1 x 10(-12) cm(2)/s for near-surface flow linear velocities ranging from 192 to 2952 mu m/s. This increase in apparent diffusion coefficient with fluid flow rate suggests increasing contributions from convective mass transport that are indicative of flow field penetration into the polymer film. The depth of penetration of the flow field is estimated to range from similar to 6% of the polymer film thickness in a good solvent at similar to 192 mu m/s to similar to 60% of the film thickness at similar to 2952 mu m/s. Thus, flow field penetration into polymer thin films, with its concomitant contributions from convective mass transport within the near-interface region of the polymer, is demonstrated and quantified experimentally.

Forced In‐plane Flow Through Complex Deformable Structures: Influence of an Imposed Curve

Visualization And Quantification Of Forced In-Plane Flow Through Deformed Porous Media

Conformations and Migration Behaviors of Confined Semiflexible Polymers under Poiseuille Flow

Rheological Properties of Fiber Suspensions Flowing Through a Curved Expansion Duct

Microstructures of Polymer Solutions of Flow Past a Confined Cylinder

A Comparison of the Unidirectional and Radial In‐plane Flow of Fluids Through Woven Composite Reinforcements

Physical Constraint Flow Field Reconstruction Method for Immersion Scan-Step Flow

Hydrodynamically Induced Preform Deformation

Fabric draping simulation in composites manufacturing. Part I: Description and applications

Numerical Simulation of Two-Phase Flow in Liquid Composite Moulding Using VOF-Based Implicit Time-Stepping Scheme

Flow rate-pressure drop relations for shear-thinning fluids in deformable configurations: theory and experiments

Resin Impregnation During the Manufacturing of Composite Materials Subject to Prescribed Injection Rate

Flow Field Penetration in Thin Nanoporous Polymer Films under Laminar Flow by Förster Resonance Energy Transfer Coupled with Total Internal Reflectance Fluorescence Microscopy.

Flow rate–pressure drop relations for shear-thinning fluids in deformable configurations: Theory and experiments

A 2D modeling approach for fluid propagation during FE-forming simulation of continuously reinforced composites in wet compression moulding

Characterization of 3D fiber preform permeability tensor in radial flow using an inverse algorithm based on sensors and simulation

A novel approach to simulate the resin infusion process by two phases coupling free and porous flows intra and inter fiber tows of liquid composite molding

Direct Nanoscopic Measurement of Laminar Slip Flow Penetration of Deformable Polymer Brush Surfaces: Synergistic Effect of Grafting Density and Solvent Quality

Multiphase Viscoplastic Flows in a Nonuniform Hele-Shaw Cell: A Fluidic Device to Control Interfacial Patterns

3D Flow Simulation for Viscous Nonisothermal Incompressible Fluid in Injection Molding

Curvature-mediated Programming of Liquid Crystal Microflows