Abstract:Gas atomized Cu50Zr45Al5 amorphous powder was densified by spark plasma sintering, in order to obtain bulk metallic glasses with larger size than that obtained by the conventional casting strategy. The influence of different parameters was investigated: sintering temperature, isothermal holding time as well as size of the specimens. After optimization of the processing parameters, dense and amorphous specimens were elaborated with a diameter up to 30mm. Thermal stability and mechanical properties of consolidated samples are similar to those of Cu50Zr45 Al5 cast alloy. A hardness of 535 HV and a compressive strength of 1600MPa have been obtained. Fractographic investigation indicated an intergranular rupture mode which leads to lower toughness compared to as the cast material, but for these samples the size is limited to 3mm. However an increase in applied pressure (from 90MPa to 1GPa) induces a significant improvement in bonding between powder particles.

Microstructure and Mechanical Properties of Crystalline Particulates Dispersed Ni-based Metallic Glassy Composites Fabricated by Spark Plasma Sintering

Large-size Ultrahigh Strength Ni-based Bulk Metallic Glassy Matrix Composites with Enhanced Ductility Fabricated by Spark Plasma Sintering

Microstructure and properties of ceramic particulate reinforced metallic glassy matrix composites fabricated by spark plasma sintering

Cu Particulate Dispersed Cu50Zr45Al5 Bulk Metallic Glassy Composite with Enhanced Electrical Conductivity

Cu Particulates Dispersed Bulk Metallic Glass Composites with High Strength and High Electrical Conductivity Fabricated by Spark Plasma Sintering

Microstructure and Mechanical Properties of Porous Zr55Cu30Al10Ni5 Bulk Metallic Glass Fabricated by Spark Plasma Sintering Process

Densification of Gas Atomized Ni-Based Metallic Glassy Powders by Spark Plasma Sintering

Fabrication of Ni<sub>52.5</sub>Nb<sub>10</sub>Zr<sub>15</sub>Ti<sub>15</sub>Pt<sub>7.5</sub> Bulk Metallic Glassy Matrix Composite Containing Dispersed ZrO<sub>2</sub> Particulates by Spark Plasma Sintering

Fabrication of ZrCuAlNi Metallic Glassy Matrix Composite Containing ZrO2 Particles by Spark Plasma Sintering Process

Characterization of Interface Between the Particles in NiNbZrTiPt Metallic Glassy Matrix Composite Containing SiC Fabricated by Spark Plasma Sintering

Ceramic Particulate Reinforced Zr55Cu30Al10Ni5 Metallic Glassy Matrix Composite Fabricated by Spark Plasma Sintering

Spark Plasma Sintering Of Al(2)O(3) Particulate Dispersed Zr(55)Cu(30)Al(10)Ni(5) Metallic Glassy Matrix Composite

Fabrication of Porous Zr–Cu–Al–Ni Bulk Metallic Glass by Spark Plasma Sintering Process

Spark Plasma Sintering of Al<sub>2</sub> O<sub>3</sub> Particulate Dispersed Zr<sub>55</sub> Cu<sub>30</sub> Al<sub>10</sub> Ni<sub>5</sub> Metallic Glassy Matrix Composite

Bulk Metallic Glassy Composites with Excellent Electrical Conductivity and Enhanced Plasticity Fabricated by Spark Plasma Sintering

Influence of Spark Plasma Sintering Parameters on the Mechanical Properties of Cu50Zr45Al5 Bulk Metallic Glass Obtained Using Metallic Glass Powder

Porous Bulk Metallic Glass Produced By Spark Plasma Sintering Of Gas Atomized Zr55cu30al10ni5 Glassy Powders

Microstructure and mechanical properties of SiC–mullite nanocomposite prepared by spark plasma sintering

Consolidation Behavior of Cu-Zr-Al Metallic Glass Powder by Spark Plasma Sintering

Ti Particles Dispersed Ti-Based Metallic Glass Matrix Composite Prepared by Spark Plasma Sintering

Spark Plasma Sintering of Gas Atomized AlNiYLaCo Amorphous Powders