Abstract:Interest in the seakeeping loads of vessels has increased dramatically in recent years. While many studies focused on predicting seakeeping loads, little attention was given on how loads are transferred to 3D finite-element models. In current design practice, methods for predicting seakeeping motions and loads are mainly based on the potential flow theory, either strip theory methods or 3D-panel methods. Methods based on strip theory provide reasonable motion prediction for ships and are computationally efficient. However, the load outputs of strip theories are only hull girder sectional forces and moments, such as vertical bending moment and vertical shear force, which cannot be directly applied to a 3D finite-element structural model. Methods-based 3D panel methods can be applied to a wide range of structures, but are computationally expensive. The seakeeping load outputs of panel methods include not only the global hull girder loads, but also panel pressures, which are well suited for 3D finite-element analysis. However, because the panel-based methods are computationally expensive, meshes used for hydrodynamic analyses are usually coarser than the mesh used for structural finite-element analyses. When pressure loads are mapped from one mesh to another, a small discrepancy at the element level will occur regardless of what interpolation method is used. The integration of those small pressure discrepancies along the whole ship inevitably causes an imbalanced structural finite-element model. To obtain equilibrium of an imbalanced structural model, a common practice is to use the ‘inertia relief’ approach. However, this type of balancing causes a change in the hull girder load distribution, which in turn could cause inaccuracies in an extreme load analysis (ELA) and a spectral fatigue analysis (SFA). This paper presents a practical method to balance the structural model without using inertia relief. The method uses quadratic programming to calculate equivalent nodal forces such that the resulting hull girder sectional loads match those calculated by seakeeping analyses, either by strip theory methods or 3D-panel methods. To validate the method, a 3D panel linear code, MAESTRO-Wave, was used to generate both panel pressures and sectional loads. A model is first loaded by a 3D-panel pressure distribution with a perfect equilibrium. The model is then loaded with only the accelerations and sectional forces and moments. The sectional forces and moments are converted to finite-element nodal forces using the proposed quadratic programming method. For these two load cases, the paper compares the hull girder loads, the hull deflection and the stresses, and the accuracy proves the validity of this new method.

An Approach to Automatically Loading Wave Pressure Using APDL in ANSYS

Dynamic Analysis of Pipeline Lifting Operations for Different Current Velocities and Wave Heights

Design and Analysis of a Novel Ship Pipeline Welding Auxiliary Device

Coupled Computational Fluid Dynamics-Discrete Element Method for Simulating the Interactions Between Ship-Induced Waves and Riprap on Restricted Waterway Banks

Numerical Simulation of Wave Interaction with Coastal Structures Using a CIP-based Method

Fatigue Failure Analysis and Simulation Calculation of Submarine Suspended Pipelines

Model Analysis of Green Water Phenomena and Loading for Ship Sailing with Slow Speed

Simulation of impact load on ship-platform collision

A semi-analytical method to simulate hydroelastic slamming of 2D structural sections by coupling Wagner theory with the finite element method

Dynamic Analysis of Ship Stern with 3D Finite Element Method

CFD-FEM simulation of hydroelastic responses and slamming loads of a bow-flare ship advancing in head regular waves

Modelling Sea-Surface Wave Motion and Ship Response Using Smoothed Particle Hydrodynamics and Finite Element Analysis

A practical method to apply hull girder sectional loads to full-ship 3D finite-element models using quadratic programming

Calculation of ship floating state by quasi-Newton iteration method for onboard loading computer

Frequency-Domain 3D Computer Program for Predicting Motions and Loads on a Ship in Regular Waves

Semi-analytical dynamic modeling and fluid-structure interaction analysis of L-shaped pipeline

Numerical Simulation of Fluid Structure Interaction between Flow and Steel Pipe Pile Platform in Deep Water

A Two-Step Approach for Evaluating the Dynamic Ultimate Load Capacity of Ship Structures

Numerical Analysis on Self-Propulsion of a Waterjet-Propelled Ship with Different Propulsion Models

A new analytical model to evaluate ship side collisions with large indentation considering interaction effects between structural components

Investigation of a weathervaning FPSO based on a fully nonlinear boundary element method