Abstract:Catalysis with phosphorus P(III) compounds (phosphorus trichloride and phosphorous acid) in the acylation of aniline with 3=hydroxy=2=naphthoic acid in various media (toluene, octane, chlorobenzene, para=xylene, ortho=xylene, ortho=chlorotoluene, mesitylene, pseudocumene, n.=deсan, ortho= dichlorobenzene, mixtures of ortho=xylene with nitrobenzene) upon boiling and vigorous distillation of water leads to the formation of 3=hydroxy=2=naphthoic acid anilide. With an increase in the reaction temperature in the range from 111 (toluene) to 170 °C (pseudo cumene), a monotonous increase in the initial rate of formation of the target product is observed. In this case, the temperature dependence of the logarithm of the velocity obeys the Arrhenius equation, and the activation energy Ea is 66.2 kJ/mol. Higher-boiling n.=decane (175 °С) and ortho=dichlorobenzene (180 °С) fall out of this dependence, in which the initial rate of formation of anilide 3=hydroxy=2=naphthoic acid, compared with that for pseudocumene (170 °С), decreases. The latter may be due to the decomposition or oxidation of the catalyst at such a high temperature with the transition of P(III) to P(V), which does not have catalytic activity. The interaction of aniline with 3=hydroxyl=2=naphthoic acid proceeds as a series of sequential and parallel reactions in which, in addition to 3=hydroxyl=2= naphthoic acid anilide, 3=aniline=2=naphthoic acid and its anilide are formed as impurities. The most acceptable solvents are ortho=xylene and ortho=chlorotoluene with boiling points of 146 and 156°C, in which the yield of the target product is up to 98%. Below 146 °C the reaction proceeds at a relatively low rate; above 156°C the amount of impurities increases significantly, mainly in parallel with an increase in the reaction temperature, and the maximum yield of 3=hydroxyl=2=naphthoic acid anilide decreases. This requires its additional purification, significantly complicating the technological process. The addition of 10–20% by volume of nitrobenzene to ortho=xylene leads to an increase in the yield of 3=oxy=2=naphthoic acid anilide by 1.25–1.42 times in the temperature range of 146–148°C with increasing solvent polarity (ε), respectively, from 2.3 to 7.64. This may be due to an increase in the quantity of the monomers of the catalyst and/or 3=oxy=2=naphthoic acid and aniline in reaction mass and the speed of water separation.

Synthesis of Heptafluoroisopropyl-containing Aniline Compounds

Synthesis of Aromatic Aldehyde Containing Electronwithdrawing Groups

Synthesis of Isophorone Diamine and its Reaction Condition Optimization

Synthesis of 4-Hydroxy-3-methoxyphenylacetonitrile

Kinetics and Simulation of the Imidization of Poly(styrene‐co‐maleic Anhydride) with Amines

Synthesis of 2,6-dichloro-3-methylaniline

Synthesis of Novel Phenoxyimine Ligands Containing A 2,6-Difluoro-4-styrylaniline

Improved Synthesis of 2-Methoxyphenothiazine.

Study on the Synthesis of N, N'-Bis(4-nitropheoyl)urea

Synthesis of p-(Trifluoromethyl)thiobenzamide

Synthesis of 4,4'-Dinitrodiphenyl Sulfone

A Practical Synthesis Route of p-Fluorophenol

Practical heptafluoroisopropylation of nitrogen-containing (hetero)aromatics under visible light

Synthesis of 2-Aminoxy-1-aminoethane Dihydrochloride

HFIP-Promoted Selective Hydroxyalkylation of Aniline Derivatives with Arylglyoxal Hydrates

Synthesis of Substituted Phenyl Isocyanates by Bis(trichloromethyl) Carbonate Method

Process Improvement on the Synthesis of 1-(3,5-dimethylphenyl)-1-[ (1S,4s)-1,7,7-trimethyl-bicyclo[2.2.1] Heptan-2-yl] Hydrazine

Synthesis Of N-Phenyl-2-Methyl-4-Methoxyaniline

Efficient Synthesis of Difluoroacrylamide/Amine From Fluorinated Olefins Under Base Promotion

SYNTHESIS OF 3-HYDROXY-2-NAPHTHOIC ACID ANILIDE CATALYZED BY PHOSPHORUS (III) COMPOUNDS IN VARIOUS MEDIA

Practical Synthesis of N-Anilinylphenothiazines Using a Cyclic Hypervalent Iodine Coupling Reagent