Abstract:For resource reutilization, scrap tyres have long been investigated as an additive to concrete to form 'Rubcrete' for various applications and have shown promising results. However, the addition of rubber particles leads to the degradation of physical properties, particularly, the compressive strength of the concrete. In this study, a theoretical model was proposed to shed light on the mechanisms of decrease in compressive strength due to the addition of rubber particles as well as improvement in compressive strength through modification of particle surfaces. The literature suggests that the compressive strength can be improved by soaking the rubber particles in alkaline solution first to increase the inter-phase bonding between the rubber particles and cement. Instead, we discovered that the loss in compressive strength was due to local imperfections in the hydration of cement, induced by the addition of heterogeneous and hydrophobic rubber particles. Microscopic studies showed that the rubber particles disturbed the water transfer to create channels, which were prone to cracking and led to a loss in the compressive strength. Unexpectedly, no cracking was found along the surfaces of the rubber particles, indicating that the bonding strength between the rubber particles and cement phases was not the critical factor in determining the compressive strength. Therefore, a theoretical model was proposed to describe the water transfer in the Rubcrete specimens to explain the experimental data. In the model, the local water available for hydration (Q) is: Q = -A(slv)/6piv, where Q, A(slv), and v are mass flow rate (kg s(-1)), Hamaker constant (J), and dynamic viscosity (m2 s(-1)), respectively. By maximizing the quantity Q and, in turn, the Hamaker constant A(slv), the compressive strength could be improved. The Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that for the hydrated cement particles; the water transfer rate was lower in the presence of rubber particles because the Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that on the hydrated cement particles. Thus, the compressive strength of Rubcrete could be improved by increasing the Hamaker constant of the system. This was achieved by increasing the refractive indices of the solids (n(s)). The refractive indices of materials increase with increases in functional groups, such as OH and SH on the surface. The model provided a possible mechanism for the efficacy of treating rubber particles with NaOH in improving the compressive strength. By using NaOH solution treatment, an oxygen-containing OH group was formed on the rubber surface to increase the Hamaker constant of the system, leading to higher compressive strength. Based on this mechanism, a novel method for modification of the rubber particles was also proposed. In this process, the rubber particles were partially oxidized with hot air/steam in a fluidized bed reactor to produce the hydrophilic groups on the surface of the particles. Preliminary results obtained so far are promising in accordance with the theory.

Study on Compressive Strength and Interface of Rubberized Concrete

Experimental Investigation on the Dynamic Compressive Behavior of Rubberized Concrete

Impact of Rubber Content on Performance of Ultra-High-Performance Rubberised Concrete (UHPRuC)

Performance analysis and engineering application of waste rubber crumbs in concrete

Analysis of Cube Compressive Strength on Concrete with Recycled Aggregate and Rubber Particles

Experimental and numerical investigation on fracture characteristics of self-compacting concrete mixed with waste rubber particles

A Review of the Durability-Related Features of Waste Tyre Rubber as a Partial Substitute for Natural Aggregate in Concrete

Research on static mechanical properties of high-performance rubber concrete

Strength, durability and shrinkage behaviours of steel fiber reinforced rubberized concrete

Investigation of the Behaviour of Concrete Containing Waste Tire Crumb Rubber

Effect of compression casting method on the compressive strength, elastic modulus and microstructure of rubber concrete

Experimental investigation on the impact resistance of rubber self-compacting concrete

Examination of the permeability of rubberized concrete with different water/cement ratios and their resistance against acid and sulfate attack

Thermal and Mechanical Properties of Concrete Incorporating Silica Fume and Waste Rubber Powder

Rubber/crete: Mechanical properties of scrap to reuse tire-derived rubber in concrete; A review

Use of waste rubber as concrete additive

Experimental investigation into the properties of crumb rubberized concrete incorporating corrugated round steel fibers

Investigative Experimental Research: Effects of Waste Rubber as an Additive Substitute for Coarse Aggregates on the Compressive Strength of the Concrete

Influence of Basalt/Polypropylene Fiber on Permeability and Uniaxial Compressive Properties of Waste Tire Rubberized Concrete

Experimental investigation of concrete prepared with waste rubber and waste glass

Enhancing high-performance concrete sustainability: integration of waste tire rubber for innovation