Abstract:Refractory materials used for the lining of metallurgical vessels are in direct contact with moving molten steel during the entire refining process. The dynamic interaction between molten steel and refractory material will seriously affect the service life of the refractory lining and restrict the smelting safety and efficiency of steelmaking. In this paper, experiments on the interaction between an alumina-magnesia castable and molten steel under dynamic smelting conditions were performed. The corrosion behaviour of molten steel on the alumina-magnesia refractory, which is the prevailing lining material for the refining ladle, was analysed and discussed. The corrosion mechanism of the alumina-magnesia refractory indicated that the refractory castable reacts with the molten steel and forms a metamorphic layer at the interface that has a liquid phase at high temperatures. The liquid oxide layer is emulsified with the molten steel under dynamic conditions such that the castable is eroded into the molten steel first, and steel droplets are continuously diffused into the castable and grow, which expands the scope of the reaction layer and gradually degrades the refractory castable. Consequently, the castable is peeled into the molten steel, and the molten steel is polluted. The reaction products of refractory castable and molten steel with different chemical compositions vary, and the viscosity of the reaction layer at high temperatures is the key factor. The modified capillary number (Ca*) can be used to compare the refractory wear by estimating the critical velocity of the emulsification. Furthermore, the empirical formulas for the emulsion droplet size were established, providing guidance for the application of refractory materials in the smelting of high-quality steel.

Investigation on High Chromium Corundum Coating and Its Resisting Burn-on Mechanism

Effect of Submicron SiC Particles on the Properties of Alcocrfeni High Entropy Alloy Coatings

Corrosion behavior and failure mechanism of amorphous Al2O3 coating at high-temperature LBE

Research and Application on Alcohol-Base Resisting Penetration Sand State Coating Substituting for Zircon Coating

The Effect of Annealing on Microstructure and High Temperature Erosion Property of Arc-Spraying Coatings Containing Nanosized Ceramic Powders

Investigation On The Microstructure And Wear Behavior Of Laser-Cladded High Aluminum And Chromium Fe-B-C Coating

Slag Corrosion Resistance of Al2O3-ZrN-Sialon-C Refractories

Investigation on Mircro-Structure of Zircon Coating

Corrosion mechanism of cement-bonded Al2O3–MgAl2O4 pre-cast castables in contact with molten steel and slag

Study Of Ceramic Composite Coating On Steel Plate By Combustion Synthesis

Microstructure and High Temperature Oxidation Resistance of FeMnCrAl/Cr3C2 Coatings Deposited by High Velocity Arc Spraying

Development and Characterization of High-temperature and Laser Ablation Resistant Coating

Microstructural Transformation and High-Temperature Aluminum Corrosion Properties of Co-Based Alloy Coating Prepared by Laser Cladding

High Temperature Oxidation and Tribological Behavior of Cr3C2-25CoNiCrAlY and Cr3C2-25NiCr Coatings Prepared by AC-HVAF

Research Status of High Chromium Cast Iron Coating

Dynamic interaction of refractory and molten steel: Corrosion mechanism of alumina-magnesia castables

Preparation of CaCO3 coated corundum aggregates by dip-coating and heat treatment and its effects on the properties and microstructures of Al2O3–MgO castables

The Effect of Chromium on the Gamma to Alpha Phase Transition of Alumina Coating Formed on 316L SS by a Cathodic Micro Arc Deposition (CMAD) Process

Effect of composite micro-powder added with α-Al2O3 and zirconium basic carbonate on the structure and properties of corundum castable

Preparation and properties of sol-gel Al_2O_3 coating on carbon steel

Corrosion mechanism of A508 molten steel on carbon containing refractories for steel ladle