Abstract:<p>In this study, the SiC/Al-Zn-Mg-Cu nanocomposites were fabricated using high energy mechanical milling combined with spark plasma sintering (SPS) and hot extrusion. The microstructure and mechanical properties were investigated by utilizing X-ray diffraction (XRD), scanning electron microscopy (SEM) and high resolution transition electron microscopy (HRTEM) analysis as well as tensile tests. The results showed that the as-extruded SiC/Al-Zn-Mg-Cu nanocomposite samples demonstrated a microstructure consisting of ultrafine α-Al grains, dispersed SiC nanoparticles and nano-scaled T phases probably formed by dynamic precipitation during extrusion. After T6 heat treatment, the coarsening of α-Al grains, dissolution of T phases and consequently the precipitation of fine η′ phases occurred, leading to a simultaneous increase of the strength and ductility. With increasing the content of SiC nanoparticles from 1 vol% to 3 vol%, the yield strength (YS) and ultimate tensile strength (UTS) increased from 456 and 528 MPa to 580 and 588 MPa (27.2% and 11.4% increase), respectively while the elongation to fracture decreased slightly from 11.8% to 10.2% (13.6% decrease). Various strengthening mechanism calculation results show that grain boundary strengthening and Orowan strengthening were mostly contributed to the improved strength of the T6 heat treated SiC/Al-Zn-Mg-Cu nanocomposites.</p>

Microstructure and Mechanical Properties of SiC/Mullite and SiC/ZTM Nanocomposites

Microstructure and Mechanical Properties of SiC/zirconia-toughened Mullite Nanocomposites Prepared from Mixtures of Mullite Gel, 2Y-TZP, and SiC Nanopowders

SiC/ZTM Nanocomposite with Needlelike Mullite Grains and Enhanced Mechanical Properties

Microstructure and mechanical properties of SiC–mullite nanocomposite prepared by spark plasma sintering

Mechanical Performances of ZTM/SiC Nanocomposite Optimized Through Composition and Microstructure Tailoring

Mechanical Properties and Microstructure of Sic-Zro2(3y)-Al2o3 Nanocomposites

Microstructure and mechanical properties of ZrB2–SiC nanocomposite ceramic

Synthesis of Spherical (30 Nm) and Rod-Like (200 Nm) Zirconia Co-Reinforced Mullite Nanocomposites

Fabrication, Microstructural Evolution, and Mechanical Properties of SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C Nanocomposites

Nano-Zirconia/Mullite Composite Ceramics Prepared By In-Situ Controlled Crystallization From The Si-Al-Zr-O Amorphous Bulk

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Microstructure and Properties of Zirconia-Mullite Nanocomposites Obtained from Si-Al-Zr-O Amorphous Bulks Doped with CaO and MgO

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

Influence of SiC particle size on microstructure and mechanical properties of Al2O3-SiC nanocomposites

Fabrication and Mechanical Properties of Nano-SiC-Oxide Composites

Mechanical Properties and Structure of Zirconia-Mullite Ceramics Prepared by In-Situ Controlled Crystallization of Si-Al-Zr-O Amorphous Bulk

Structure and Mechanical Properties of ZrO 2 -Mullite Nano-Ceramics in SiO 2 -Al 2 O 3 -Zro 2 System

Structure and Mechanical Properties of ZrO_2-mullite Nano-Ceramics in SiO_2-Al_2O_3-ZrO_2 System

Preparation and Mechanical Properties of SiC Whisker and Nanosized Mullite Particulate Reinforced TZP Composites

Influence of SiCnp Content on the Microstructure and Mechanical Properties of ZrB2–SiC Nanocomposite

Microstructures and Mechanical Properties of Mullite/SiC Composite Ceramics Prepared by Gelcasting