Abstract:In this study, the change of the resistivity of the CNT-dispersed resin was analyzed by applying a quantum chemical molecular dynamics and the first principle calculation. Various combinations of double-walled carbon nanotube structures were modeled for the analysis. The change of the band structure was calculated by changing the amplitude of the applied strain. It was found in some cases that the band structure changes drastically from a metallic structure to a semiconductive structure, and this result clearly indicated that the electronic conductivity of this MWCNT decreased significantly under tensile strain. It was also found that further application of the strain made a band gap in the band structure. This result indicated that the metallic CNT changes a semiconductive CNT due to the applied strain. The effect of the diameter of the zigzag type CNT on the critical strain of buckling deformation was analyzed under a uni-axial strain. In this analysis, the aspect ratio of each structure was fixed at 10. It was found that the critical strain decreased monotonically with the increase of the diameter. This was because that the flexural rigidity of a cylinder decreased with the increase of its diameter when the thickness of the wall of the cylinder is fixed. It was found that the critical strain decreased drastically from about 5% to 0.5% when the aspect ratio was changed from 10 to 30. Since the typical aspect ratio of CNTs often exceeds 1000, most CNTs show buckling deformation when an axial compressive strain was applied to the CNTs. Finally, the shape of six-membered ring of the CNT was found to be the dominant factor that determines the electronic band structure of a CNT. Next, the change of the band structure of a graphene sheet was analyzed by applying the abinitio calculation (Density functional theory). It was found that the fluctuation of the atomic distance among the six-membered ring is the most dominant factor of the electronic band structure. When the fluctuation exceeded about 10%, band gap appeared in the deformed six-membered ring, and thus, the electronic conductivity of the graphene sheet changes from metallic one to semiconductive one. It is therefore, possible to predict the change of the electronic conductivity of a CNT by considering the local shape of a six-membered ring in the deformed CNT.

Band Gap of Carbon Nanotubes under Combined Uniaxial–torsional Strain

Effect of Uniaxial Strain on the Band Gap of Zigzag Carbon Nanotubes

Strain-Induced Bandgap Engineering In C3n Nanotubes

Sharp bends in photonic crystal waveguides as nonlinear Fano resonators

Mechanical and Thermal Properties of Graphyne-Coated Carbon Nanotubes: a Molecular Dynamics Simulation on One-Dimensional All-Carbon Van Der Waals Heterostructures

Resonant Raman Spectroscopy Of Deformed Single-Walled Carbon Nanotubes Under Both Torsional And Tensile Strain

G-Band Variation of Individual Single-Walled Carbon Nanotubes under Torsional Strain

Nanostructure Dependence of the Electronic Conductivity of Carbon Nanotubes and Graphene Sheets

Electronic structures of deformed B2C nanotubes under tensile strain

Band Gap of Strained Graphene Nanoribbons

Estimation of the Band Gap of Carbon Nanotube Bundles

Directly Correlating the Strain-Induced Electronic Property Change to the Chirality of Individual Single-Walled and Few-Walled Carbon Nanotubes

The Effects of Curvature, Relaxation and Mechanical Deformation on the Electronic Properties of Single-Walled Carbon Nanotubes

Strain Dependent G-band Mode Frequency of Single-Walled Carbon Nanotubes

Axial strain and twist-induced changes in the electronic structure of carbon nanotubes

Band-gap Modulation of Graphane-Like SiC Nanoribbons under Uniaxial Elastic Strain

The Influence of Mechanical Deformation on the Electrical Properties of Single Wall Carbon Nanotubes

Energy Gap Tuning in Uniaxial Strained Zigzag Graphene Nanoribbons

Energy Gap of Strained Graphene with Tight-Binding Model

Electron Properties of Deformed Armchair Single-Walled Carbon Nanotubes with Small Diameter

Constraints of mixing matrix elements in the sequential fourthgeneration model