Abstract:Perovskite oxide La0.6Sr0.4Co0.2Fe0.8O3-delta (LSCF6428), a wonderful electronic-ionic conductor could be used as cathode of solid oxide fuel cell (SOFC). Graded cathode with coarse layer and fine layer, could improve the diffusion rate and electrochemical reaction activity of oxidant. The fabrication and properties of graded LSCF6428 cathode were discussed in this paper. First, pure perovskite LSCF6428 powders were prepared by citrate-EDTA method (CEM), citrate method (CM) and solid phase synthesis (SPS). The powders with higher specific surface area and smaller grain size are easier to be sintered and densified. Single LSCF6428 cathode with thickness of 30 mu m was prepared by SPS powders, the porosity of cathode was high about 30% and pore size was about 5 mu m. Graded LSCF6428 cathode including 30 gm outer layer and 10 mu m inner layer was prepared by SPS and CM powders, respectively. Clear double-layer cathode was observed by SEM, which combined tightly and transited gradually. Porosity of outer layer is high about 30% and pore size is about 1-5 mu m; inner layer is finer and pore size is about 0.2-1 mu m. Based on the above research, 300 mu m yttria stabilized zirconia (YSZ) electrolyte supported cell with single LSCF6428 cathode and double-layer LSCF6428 cathode were prepared, and the properties of two type cells were tested in H-2. Power density of graded cell is 197 mW cm(-2) at 950 degrees C, and improved about 46% comparing that of single layer LSCF6428 cell (135 mW cm(-2)). (C) 2007 Elsevier B.V. All rights reserved.

Functionally Graded Cathodes for Honeycomb Solid Oxide Fuel Cells

LSM-GDC Composite Cathodes Derived from a Sol-Gel Process

Composite Cathode Based on Yttria Stabilized Bismuth Oxide for Low-Temperature Solid Oxide Fuel Cells

Preparation And Characterization Of Graded Cathode La0.6sr0.4co0.2fe0.8o3-Delta

Preparation and Characterization of Graded Cathode La0.6Sr0.4Co0.2Fe0.8O3−δ

Scandia-stabilized Zirconia-Impregnated (la, Sr)MnO 3 Cathode for Tubular Solid Oxide Fuel Cells

Fabrication and performance of functionally graded cathodes for IT-SOFCs based on doped ceria electrolytes

Preparation of Honeycomb Porous Solid Oxide Fuel Cell Cathodes by Breath Figures Method

Fabrication and Performance of La0.6sr0.4co0.2fe0.8o3-Delta Infiltrated-Yttria-Stabilized Zirconia Cathode on Anode-Supported Solid Oxide Fuel Cell

In-Silico Design of Functionally Graded Electrodes for Solid Oxide Fuel Cells

Development of Lsm-Based Cathodes for Solid Oxide Fuel Cells Based on Ysz Films

Preparation of Honeycomb Porous La0.6Sr0.4Co0.2Fe0.8O3−δ–Gd0.2Ce0.8O2−δ Composite Cathodes by Breath Figures Method for Solid Oxide Fuel Cells

Design and Optimization of Functionally Graded Electrodes for Solid Oxide Fuel Cells (sofcs) by Mesoscale Modeling

Novel functionally graded acicular electrode for solid oxide cells fabricated by the freeze-tape-casting process

La[sub 0.85]sr[sub 0.15]mno[sub 3−δ] Infiltrated Y[sub 0.5]bi[sub 1.5]o[sub 3] Cathodes for Intermediate-Temperature Solid Oxide Fuel Cells

High Performance Yttria-Stabilized Zirconia Based Intermediate Temperature Solid Oxide Fuel Cells with Double Nano Layer Composite Cathode

Optimisation and Evaluation of La0.6Sr0.4CoO3 – Δ Cathode for Intermediate Temperature Solid Oxide Fuel Cells

La0.4sr0.6co0.2fe0.7nb0.1o3-Delta Electrodes for Ysz-Based Symmetrical Sofc

Fabrication and Optimization of La 0.4 Sr 0.6 Co 0.2 Fe 0.7 Nb 0.1 O 3- Δ Electrode for Symmetric Solid Oxide Fuel Cell with Zirconia Based Electrolyte

Synthesis and Evaluation of Ca-doped Sr2Fe1.5Mo0.5O6-δ As Symmetrical Electrodes for High Performance Solid Oxide Fuel Cells

Performance Degradation of Impregnated La0.6Sr0.4Co0.2Fe0.8O3+Y2O3 Stabilized ZrO2 Composite Cathodes of Intermediate Temperature Solid Oxide Fuel Cells