Abstract:Intermittent oil-water wetting can have a significant effect on the internal corrosion of steel pipelines. This paper presents a combined experimental and molecular modeling study of several influential factors on the surface properties and corrosion behavior of mild steel in CO2 environments. The influence of different model oils (LVT-200 and Aromatic-200) and select surface-active compounds (myristic acid, cyclohexane butyric acid, and oleic acid) on the corrosion behavior of carbon steel during intermittent oil-water wetting was determined by measuring the corrosion rate after intermittent wetting cycles. The interfacial tension measurements were performed to study the incorporation of the oil phase along with surface-active molecules in the protective layer formed on the specimen surface. Results showed that the interfacial tension for an aromatic oil-water interface is lower than that for an aliphatic oil-water interface. To understand this result, molecular dynamics simulations of oil-water interfaces were performed in the presence of surface-active molecules and different oils to analyze the structure of the layer formed at the interface. The simulations supported the hypothesis that aromatic molecules are less structured at the interface, which results in the incorporation of more water molecules into the protective layer formed at the steel surface, causing a higher corrosion rate. On the other hand, the simulations revealed that myristic acid in an aliphatic oil forms a well-aligned structure at the interface, devoid of any water molecules. This is in agreement with the hypothesis that the linear molecular structure of myristic acid favors the alignment of molecules at an aliphatic oil-water interface, resulting in a lower interfacial tension and more effective corrosion mitigation as compared to the other two nonlinear compounds tested. It is concluded that an important factor controlling the corrosion behavior is the molecular structure of the oil-water interface, which is adopted by the steel surface layer through the Langmuir-Blodgett process.

Ostwald ripening: a decisive cause of cylinder corrosive wear

Acid Neutralization by Marine Cylinder Lubricants Inside a Heating Capillary: Strong/Weak-Stick Collision Mechanisms

Influence of Oxidative Degradation of Lubricant and Anti-Friction Modifier on Tribological Behavior of Cylinder Liner/Piston Ring

Study on the corrosion and wear behaviors of cylinder liner in marine diesel engine burning low sulfur fuel oil

Temperature and acid droplet size effects in acid neutralization of marine cylinder lubricants

Coupled Evolution of Piston Asperity and Cylinder Bore Contour of Piston/cylinder Pair in Axial Piston Pump

Experimental and Numerical Studies on Erosion Damage in Damping Holes on the Valve Plate of an Axial Piston Pump

Effects of Different Cathodic Reactions on Tribocorrosion Behavior of AISI 430 in 0.5 mol/L Sulfuric Acid

The Corrosive Effects of Aftermarket Oil Additives on High-Leaded Tin Bronze Alloy

Coupled evolution process of lubrication and wear in piston-liner interface of high-pressure common rail pumps

Catalyzing Green Lubricants into Graphitic Carbon Layers by Iron Single Atoms to Reduce Friction and Wear

Competitive Surface Interactions of Critical Additives with Piston Ring/Cylinder Liner Components under Lubricated Breaking-In conditions

Ostwald ripening in an oxide-on-metal system

Tribocorrosive Aspects of Tungsten Carbide, Silicon Nitride, and Martensitic Steel under Fretting-like Conditions

Effects of surface deformation on corrosive wear of stainless steel in sulfuric acid solution

Effects of Σ Phase in Stainless Steels on Corrosive Wear Behavior in Sulfuric Acid

Corrosion behaviors of cylinder liner in marine diesel engine burning low sulfur fuel oil: An experimental and molecular dynamics simulation study

Experiments and Molecular Simulations to Study the Effect of Surface-Active Compounds in Mixtures of Model Oils on CO2 Corrosion during Intermittent Oil-Water Wetting

An experimental investigation of adhesive wear extension in fretting interface: application of the contact oxygenation concept

Synergism Between Wear and Corrosion of Cr26Mo1 Ferrite Stainless Steels in 0.5 mol/L of Sulfuric Acid

Investigation of the Corrosion–Wear Interaction Behavior of 8Cr4Mo4V Bearing Steel at Various Corrosion Intervals