Abstract:In recent years a considerable amount of research has been undertaken in the development of the piezoelectric actuator for active structural acoustic control (ASAC). Some researchers have concentrated on the optimisation of the parameters of the piezoelectric actuators; for instance, the number, sizes, locations and voltages applied to the actuators to minimise either structural vibration or radiated sound power . In the work of Wang et al. , a mathematical formulation for the optimisation of the locations of piezoelectric actuators in a feedforward control implementation of ASAC was given. They demonstrated that optimally located piezoelectric actuators can provide a large reduction in the amount of sound power radiated, and are observed to perform better than actuators in arbitrarily chosen locations. Based on the object function selected in their work, Wang et al. found that properly locating one piezoelectric actuator generally gives greater reduction of radiated sound power than using two or three actuators. Recently, Varadan et al. 4 have reported on the optimisation of the placement of circular disk-shape piezoelectric actuators on a clamped rectangular plate, using the finite element method. They found that the optimal locations of piezoelectric actuators to minimise sound radiation are near the corners rather than the centre of the plate. This is because the edges and corners of flat plates contribute most to the radiated sound power at frequencies below the plate critical frequency, the frequency range of the results reported. Another application of PZT actuators their use to excite a panel control sources to replace loudspeakers in ANVC (Li et al. ). In the work of Li et al. , a tuned curved panel sound source for use with active systems for controlling transformer sound was developed. If this kind of sound source is used in the place of loudspeakers, the number of control sources and the complexity of the controller can be reduced substantially. To prevent the interaction and cancellation of the sound radiation from the two sides of the panel, a cavity was coupled to one side of the panel. The reasons for using a curved panel rather than flat panel are twofold: first a curved panel is more easily excited by piezoelectric patch actuators because the bending vibration of the curved panel couples better with the extensional motion of the actuators; and second, it is not possible to adjust the resonance frequencies of the efficient modes of a flat panel very easily. In this paper, a curved panel with a backing cavity driven by rectangular PZT actuators 7 has been modelled. Simple optimisation procedures for sizes and locations of the PZT actuators on the panel are given. Because the research described in this paper concerns the design of a resonant curved panel as a sound source, only optimal results for some efficient natural modes are presented. The objective of the optimisation is to maximise the structural response (velocity) of the curved panel vibrating in particular resonant modes.

Optimal Implementation of Miniature Piezoelectric Panel Speakers Using the Taguchi Method and Genetic Algorithm

Optimization methods for acoustic performance of piezoelectric panel loudspeaker.

Optimal placement of piezoelectric torsional actuator based on genetic algorithm

Determination of optimal exciter deployment for panel speakers using the genetic algorithm

Genetic Algorithm for Electro-Mechanical Co-Optimization of a MEMS Accelerometer Comprising a Mechanical Motion Pre-Amplifier with a 2Nd-Order Sigma Delta Modulator

Optimal Design of Loudspeaker Systems Based on Sequential Quadratic Programming (Sqp)

Experimental Modeling and Design Optimization of Push-Pull Electret Loudspeakers

Finite-Element Electroacoustic Analysis and Taguchi Design of Piezoelectric Buzzers Based on the Vibration Absorber Model

Optimal Control Of Piezoelectric Laminated Parabolic Cylindrical Panels

A reduced-order-model-based equivalent circuit for piezoelectric micro-electro-mechanical-system loudspeakers modeling

Space Active Noise Control System Design with Multi-Objective Genetic Algorithms

An Efficient Optimization Design for 1 MHz Ultrasonic Transmitting Transducer

The Optimal Location of Piezoelectric Sensor/Actuator Based on Adaptive Genetic Algorithm

Noise Pollution Reduction Through a Novel Optimization Procedure in Passive Control Methods

Size Optimization of Conical Piezoelectric Energy Harvester

Optimal Sizes and Locations of Piezoelectric Actuators for Curved Panel Sound Sources

An Improved Genetic Algorithm for Thinning Acoustic Array.

Theoretical and Experimental Study on Panel Piezoelectric Loudspeaker

On the design of a two-way piezoelectric MEMS microspeaker based on a multi-shape cantilever array for high-frequency applications

Data relating to mems piezoelectric micro power harvester physical parameter optimization, for extremely low frequency and low vibration level applications

Concurrent optimization of actuator/sensor layout and control parameter on piezoelectric curved shells with active vibration control for minimizing transient noise