Abstract:The isotopic composition of sulfur is a vital tracer used in the Earth and planetary sciences. In this study, the laser-and ICP-induced isotopic fractionation in S-rich minerals (sulfides and elemental S) with different matrices was investigated by using 257 nm femtosecond (fs) and 193 nm ArF excimer nanosecond (ns) laser ablation systems coupled to a Neptune Plus MC-ICP-MS. Compared to ns-LA-MC-ICP-MS, higher sensitivity (1.4-2.4 times) under similar instrumental conditions and better precision (similar to 1.6-fold) under the same signal intensity condition were achieved by fs-LA-MC-ICP-MS. In addition, a fs-laser provides less fluence and matrix dependent S isotopic fractionation, and more stable transient isotopic ratios compared to a ns-laser. Better results acquired by fs-LA-MC-ICP-MS were attributed to the smaller size of particles and less thermal effect produced by using the fs-laser, which were evidenced by the morphologies of the ablation craters and ejected aerosol particles of P-S-1 (the pressed powder pellet of IAEA-S-1) and PPP-1 (a pyrite single crystal from the Sukhoi Log deposit). The ICP-induced isotopic fractionation (matrix effect) was still found in fs-LA-MC-ICP-MS under the maximum sensitivity conditions. However, a significant reduction of the matrix effect was obtained under robust plasma conditions at a lower makeup gas flow rate (0.52-0.54 l min(-1)) relative to the maximum sensitivity condition (0.6 l min(-1)) for S isotope analysis. This could be ascribed to the particles that not only pass into the higher temperature ICP for a longer residence time at a lower makeup gas flow rate that resulted in more efficient vaporization of the particles, but also experience a more robust plasma induced by adding 4-6 ml min(-1) N-2 into the plasma. Furthermore, under the robust conditions, the results of six reference materials with different matrices obtained by fs-LA-MC-ICP-MS with non-matrix matched calibration with a spot size of 20-44 mm showed excellent agreement with the reference values (the accuracy of 0.01-0.15 parts per thousand for delta S-34 and 0.11-0.45 parts per thousand for delta S-33 and the precision of 0.16-0.40 parts per thousand (2 s) for delta S-34 and 0.35-0.78 parts per thousand (2 s) for delta S-33) and the mass-dependent fractionation line, validating the applicability of the proposed approach for providing high-quality in situ isotope data (delta S-33 and delta S-34) of sulfides and elemental sulfur at high spatial resolution using non-matrix matched analysis.

Measurement of Sulfur Isotopic Composition by Sector Field Inductively Coupled Plasma Mass Spectrometry

Rapid and High-Precision Measurement of Sulfur Isotope and Sulfur Concentration in Sediment Pore Water by Multi-Collector Inductively Coupled Plasma Mass Spectrometry.

A Rapid and High‐precision Method for Sulfur Isotope Δ34s Determination with a Multiple‐collector Inductively Coupled Plasma Mass Spectrometer: Matrix Effect Correction and Applications for Water Samples Without Chemical Purification

Accurate Determination of Sulphur Content in Sediments by Double Focusing Inductively Coupled Plasma Mass Spectrometry Combined with Microwave Digestion and Studies on Related Matrix Effect

Accurate determination of sulfur isotopes (δ33S and δ34S) in sulfides and elemental sulfur by femtosecond laser ablation MC-ICP-MS with non-matrix matched calibration

Accurate determination of sulfur isotopes (delta S-33 and delta S-34) in sulfides and elemental sulfur by femtosecond laser ablation MC-ICP-MS with non-matrix matched calibration

High-precision measurement of 36 SF 5 + signal using the MAT 253 Ultra isotope-ratio mass spectrometer

A modified laser ablation‐isotope ratio mass spectrometry method for in situ analysis of sulfur isotope composition of sulfides

Fully resolved high‐precision measurement of 36S for sulfur reference materials

High‐accuracy measurement of 36SF5+ signal using an ultrahigh‐resolution isotope ratio mass spectrometer

Preparation of Sulfur-Bearing Reference Materials for in Situ Sulfur Isotope Measurements Using Laser Ablation Multicollector Inductively Coupled Plasma–mass Spectrometry

Silicon Isotope Compositions of Soil and Sediment Reference Materials Determined by MC-ICP-MS

New Potential Sphalerite, Chalcopyrite, Galena and Pyrite Reference Materials for Sulfur Isotope LA-MC-ICP-MS Determination

New Potential Sphalerite, Chalcopyrite, Galena and Pyrite Reference Materials for Sulfur Isotope Determination by Laser Ablation‐MC‐ICP‐MS

Development of an Online Isotope Dilution CE/ICP-MS Method for the Quantification of Sulfur in Biological Compounds

Silicon Isotope Compositions of Soil and Sediment Reference Materials Determined by MC‐ICP‐MS

Three new potential sulfur reference materials (pyrite, gypsum, and arsenopyrite) for in situ sulfur isotope analysis by laser ablation MC-ICP-MS

Continuous-Flow Stable Sulfur Isotope Analysis of Organic and Inorganic Compounds by EA-MC-ICPMS

Sulfur isotope analyses using 3× elemental analysis/isotope ratio mass spectrometry: Saving helium and energy while reducing analytical time and costs

Direct Determination of Trace Antimony in Natural Waters by Photochemical Vapor Generation Icpms: Method Optimization and Comparison of Quantitation Strategies