Abstract:In this study, Al0.6CoCrFeNi high-entropy alloy particle-reinforced 5052Al-based composites with good surface morphology and different diffusion layer thicknesses were successfully prepared using hot-press sintering and annealing, which were subsequently characterized by XRD, SEM, EBSD, micropillar compression, and nanoindentation. The EBSD tests indicate that the Al0.6CoCrFeNi high-entropy alloy has a dual-phase crystal structure with the presence of both FCC and BCC phases inside, and the internal grain size is significantly higher than that of the matrix. Subsequently, the mechanical property mapping images of the particle-diffusion layer-matrix region on the composite surface were obtained using the NanoBlitz 3D method in the nanoindentation experiments. And based on the particle and matrix mechanical property parameters obtained by nanoindentation experiments, they were fitted into different mathematical models to obtain the hardness and elastic modulus of the composite. As a result, the correlation was found to be linear, and the slope of the fitted straight line increased gradually with the prolongation of the annealing time. In conclusion, it is evident from the comparison of the results of mathematical model fitting of mechanical property parameters with the results of macroscopic mechanical property tests that the P. G. Klemens model exhibits an excellent fitting effect on the macro-microscopic mechanical properties of particle-reinforced aluminum matrix composites compared with other models such as the rule of mixtures.

Microstructure, interface and mechanical property of the DS NiAl/Cr(Mo,Hf) composite

Macro-micro Analysis of Mechanical Properties of Al0.6CoCrFeNi High-Entropy Alloy Particle-Reinforced Al-based Composites

Investigation of a Directionally Solidified NiAl/Cr(Mo) Composite Alloyed with Hf

Effect of Hot Isostatic Pressing on Microstructure and Mechanical Property of Nial/Cr(Mo,Hf) Composite

Preliminary investigation of directionally solidified NiAl–28Cr–5.5Mo–0.5Hf composite

Microstructure and Mechanical Properties Determined in Compressive Tests of Quasi-Rapidly Solidified NiAl-Cr(Mo)-Hf Eutectic Alloy after Hot Isostatic Pressure and High Temperature Treatments

Tensile Properties and Microstructure of DS NiAl—28Cr—5.8Mo—0.2Hf Alloy

Effect of HIP on precipitations and tensile properties of directionally solidified NiAl/Cr(Mo,Hf) alloy

Investigation on microstructure and mechanical property of NiAl-28Cr-5Mo-1Hf alloy

Microstructure, Brittle–ductile Transition Temperature and Elevated Temperature Compressive Behavior of the Directionally Solidified NiAl–Cr(Mo)–Hf Alloy

STUDY ON MICROSTRUCTURE AND ELEVATED TEMPERATURE MECHANICAL PROPERTY OF DIRECTIONALLY SOLIDIFIED NiAl ALLOY Ⅱ. Elevated Temperature Mechanical Property and Interface

Microstructure Characteristics and Mechanical Properties of NiAl/Cr(Hf, Ho) in Situ Composite

Deformation Behavior and Microstructure of Ds Nial/Cr(Mo) Alloy Containing Hf

Improvement of Compressive Strength and Ductility in NiAl–Cr(Nb)/Dy Alloy by Rapid Solidification and HIP Treatment

Effects of Hip and Heat Treatment on Microstructure and Compressive Properties of Rapidly Solidified Nial-Cr(Mo)-Hf Eutectic Alloy

Hot deformation behavior and microstructure evolution of NiAl-9HfO<sub>2</sub> composite

Microstructure and Phase Stability Studies on Heusler Phase Ni2AlHf and G-phase Ni16Hf6Si7in Directionally Solidified NiAl–Cr(Mo) Eutectic Alloyed with Hf

Microstructure Characteristics and Compressive Properties of NiAl-based Multiphase Alloy During Heat Treatments

Effects of Hf additions on high-temperature mechanical properties of a directionally solidified NiAl/Cr(Mo) eutectic alloy

Microstructure Evolution and Mechanical Properties' Improvement of NiAl–Cr(Mo)–Hf Eutectic Alloy During Suction Casting and Subsequent HIP Treatment

Formation mechanism of interdiffusion layer and mechanical properties of Al 0.6 CoCrFeNi high-entropy alloy/Ti composites