Abstract:In the aluminium processing industry, the tribo-corrosion of a metal by molten aluminium or its alloys is an urgent problem, as the removal of the corrosion products leads to material losses and even failure. Therefore, a novel Fe-15.3 wt % Cr-3.1 wt % B-6.2 wt % Mo alloy was designed, and its interfacial morphologies and tribo-corrosion behaviour in molten aluminium at 750 degrees C under different experimental rotation speeds and loads were systematically investigated to understand the effect of molten aluminium via the ring-on-block test (the counterbody, which was 50% of the sliding couple, was produced by Si3N4). The results show that the designed alloy exhibits better tribo-corrosion resistance than H13 steel does (for example, at a load of 10 N and a rotation speed of 300 mm s(-1), the volume loss rate of the novel Fe-15.3 wt % Cr-3.1 wt % B-6.2 wt % Mo alloy is 87.5% lower than that of H13 steel) due to the protective capability of the M2B-type (M = Fe, Cr, Mo) boride. The scanning electron microscopy (SEM), X-ray diffractometer (XRD), electron probe microanalyses (EPMA) and transmission electron microscope (TEM) analyses of the tribo-corrosion interface indicated that the tribo-corrosion of the designed alloy in molten aluminium involved physical, chemical and mechanical processes. The wear-induced mechanical effect exacerbated the tribo-corrosion interface via the initiation and propagation of micro-cracks. Meanwhile, the wear-intensified mechanical effect resulted in the failure of the M2B-type boride, which in turn facilitated matrix corrosion and accelerated tribo-corrosion.

Corrosion behaviors of Al_(0.5)FeNiCr and Al_(0.5)FeNiCrCoTi_(0.25) alloys in molten aluminum

Corrosion Resistance of 91w–6ni–3fe Refractory Metal, TiAl Compound and Iron Based Alloys in Molten Aluminum

Interfacial Morphologies and Corrosion Behaviours of Novel Fe-Cr-B Alloys Immersed in Molten Aluminium

Corrosion Behaviour of Al1.3CrFeNi Chemically Complex Alloy

Experimental and Theoretical Research on the Corrosion Resistance of Ferrous Alloys in Aluminum Melts

Corrosion behavior of novel Fe–Cr–B alloys containing high Cr content in molten aluminum

Corrosion behaviors of CoCrWAlx alloys by laser additive manufacturing in molten Al

Corrosion Behavior of a Spark Plasma Sintered Fe–20Mn–11Al–1.8C–5Cr Alloy in Molten Aluminum

Influence of Alloyed Fe on Corrosion of Ni-Cr Alloys in Molten Silicates and the Effects of Pre-Oxidation Treatment

Corrosion of Fe-Ni-Cr Alloys with Various Aluminum Additions in a Carburizing-Oxidizing Atmosphere at 900 °C

Corrosion Behavior of Austempered Ductile Iron in Molten Al

Corrosion Resistance and Interfacial Morphologies of Novel Fe-Cr-Mo-B Cast Steels in Molten Aluminum

Microstructure and Electrochemical Properties of Alx FeCoNiCrTi High-Entropy Alloys

Corrosion Behavior of FeCoNiCrAl High-Entropy Alloy in Molten NaNO3-KNO3

The Influence of A Mo Addition on the Interfacial Morphologies and Corrosion Resistances of Novel Fe-Cr-B Alloys Immersed in Molten Aluminum

Interfacial Morphology and Tribo-Corrosion Behaviour of Fe-15.3 Wt % Cr-3.1 Wt % B-6.2 Wt % Mo Alloy in Molten Aluminium

Investigation on the Corrosion Resistance of Ni-Cr-Mo-Cu-Mx Alloys

Corrosion Behavior of Al-containing CoNiV Alloys

Corrosion Behavior of Newly Designed Fe-Ni-Base Alloys in High-Temperature CO2 at 700 °C

Structures and Corrosion Properties of the AlCrFeNiMo0.5Tix High Entropy Alloys

Multiscale Corrosion-Resistance Mechanisms of Novel Ferrous Alloys in Dynamic Aluminum Melts