The current situation and prospects of water-permeable brick

DAI Wu-bin,ZENG Ling-ke,WANG Hui,CHENG Xiao-su,LIU Ping-an,SHUI An-ze

DOI: https://doi.org/10.3969/j.issn.1006-8236.2007.06.007

2007-01-01

Abstract:The classification,characteristic,production process of the water-permeable brick are summarized in this paper. Some problems and advantages are introduced.

What problem does this paper attempt to address?

Research on the performance of sand-based environmental-friendly water permeable bricks

Runze Cai,Mandula,Jinyi Chai

DOI: https://doi.org/10.1088/1755-1315/113/1/012136

2018-02-01

IOP Conference Series: Earth and Environmental Science

Abstract:This paper examines the effects of the amount of admixture, the water cement ratio, the aggregate grading, and the cement aggregate ratio on the mechanical service properties and of porous concrete pavement bricks including strength, water permeability, frost resistance, and wear resistance. The admixture can enhance the performance of water permeable brick, and optimize the design mix. Experiments are conducted to determine the optimal mixing ratios which are given as; (1) the admixture (self-developed) within the content of 5% of the cement quality; (2) water-cement ratio equal to 0.34; (3) cement-aggregate ratio equal to 0.25; (4) fine aggregate of 70% (particle size 0.6-2.36mm); and coarse aggregate of 30% (particle size: 2.36-4.75mm). The experimental results that the sand-based permeable concrete pavement brick has a strength of 35.6MPa and that the water permeability coefficient is equal to 3.5×10-2cm/s. In addition, it was found that the concrete water permeable brick has good frost resistance and surface wear resistance, and that the its production costs are much lower than the similar sand-based water permeable bricks in China.
ANALYSIS OF THE INFLUENCE OF PROCESS CONDITIONS ON THE PERFORMANCE OF ENVIRONMENT-FRIENDLY PERVIOUS BRICK

Dai Wubin,Zeng Lingke,Jian Runtong,Wu Xigui,Shui Anze,Liu Pingan,Wang Hui,Cheng Xiaosu

DOI: https://doi.org/10.3969/j.issn.1006-2874.2007.06.002

2007-01-01

Abstract:Influence of raw material particle size,body formula,molding and sintering system on the mechanical properties,porosity,permeability coefficient and average pore size of porous pervious brick using ceramic waste as main material was analyzed to provide a new alternative for the use of ceramic waste.
The Performance Characteristics of Sand Wall-like Architectural Coatings and Construction Technology for Imitation Exterior Wall Brick

XU Feng,ZHOU Xian-lin

DOI: https://doi.org/10.3969/j.issn.1009-1696.2010.12.010

2010-01-01

Abstract:Starting from the decorative effect,applications range,construction and production costs of the coatings etc.,the performance characteristics of sand wall-like architectural coatings were introduced.The advancement of the coatings in recent years was described from the coating performance improvement and enhancement,development of new varieties,expansion of paint application range and progress of construction methods etc..The construction technology of imitation exterior wall brick was the important progress among these coating application.The coating film possessed excellent decorative effect using this construction method,which was featured with process simple,easy operation and implement,and had application value.
Preparation of Permeable Paving Bricks via Geopolymeric Method

Hao SHI,Hong-wen MA,Li-nan TIAN,Shao-gang ZHANG

DOI: https://doi.org/10.16552/j.cnki.issn1001-1625.2018.03.035

2018-01-01

Abstract:The development prospect of permeable brick was introduced.A kind of non burning permeable brick was developed with fly ash and long tailings as main raw materials by using the mechanism of mineral polymerization.Meanwhile, the influence of sand to cement ratio and aggregate size on permeable brick was studied.The results show that permeable coefficient increases, splitting tensile strength and flexural strength decreases of sample as aggregate diameter grow.The permebale coefficient increases,splitting tensile strength and flexural strength decreases of samples with the increase of the ratio of aggregate and cementing materials.The structure model and mechanism of permeable brick are also discussed.It is found that the ratio of sand to cement affects the effective void of the product, and then affects the permeability of the product.
Decontamination performance and cleaning characteristics of three common used paved permeable bricks

Suhua Han,Ye Yang,Shuang Liu,Minbo Lu

DOI: https://doi.org/10.1007/s11356-020-11706-y

IF: 5.8

2020-11-23

Environmental Science and Pollution Research

Abstract:To investigate the effectiveness of different permeable bricks on the pollutants from urban rainfall runoff, three common used bricks (ceramic brick, cement brick, and steel slag brick) were selected and applied to study their decontamination performance. The influencing factors such as rainfall intensity and contaminant concentrations were investigated. Then the ultrapure water was used to wash the permeable brick to research the pollution status and cleaning characteristics by monitoring the water quality of the rinsing water. Suspended solids (SS), chemical oxygen demand (COD), ammonia nitrogen (NH4+-N), total nitrogen (TN), total phosphorus (TP), and heavy metals (Cu, Zn, Pb, and Cd) in the influent and effluent were measured. The results showed the following: (I) The upper layer of the brick may play a more critical role in purification process; the uniform and dense pore distribution of ceramic permeable brick was instrumental in the retention of particulates. (II) Contaminant concentration and rainfall intensity had a great influence on pollutants with lower removal rate and had little effect on pollutants with higher removal rate. (III) Non-sintered bricks containing a certain amount of cement increased the pH after filtration. (IV) The removal performance of permeable brick for dissolved pollutants such as COD, NH4-N, and TN was inferior to that for SS, TP, and heavy metals since the discrepancy in removal mechanism of pollutants. The study could offer a new perspective for the decontamination research of pervious bricks.

environmental sciences
Rainwater Harvest with Desert-Sand Bricks: An Adaptive Water Resources Management Strategy for Climate Change

Xiangzhou Xu,Mingyang Liu,Hang Gao,Peiqing Xiao,Yu Zhang

DOI: https://doi.org/10.1007/s11269-024-03996-5

IF: 4.426

2024-10-12

Water Resources Management

Abstract:Urbanization causes many changes to the hydrological cycle, affecting radiation flux, precipitation amount, water evaporation and evapotranspiration, and soil infiltration. This study presents an adaptive strategy to efficiently use rainwater and promote sustainable urban development: using desert sand to construct a permeable brick with intensive compressive strength, high water permeability, and low fabrication costs. Two water-permeable holes are included in the brick to allow rainwater infiltration and maintenance of the permeable pavement. Experimental results show that the mean compressive strength of the desert-sand bricks is 69.6 MPa (2.3 times the strength required by the industry standard JC/T 945–2005) and the maximum compressive strength is 102.8 MPa (3.4 times the industry standard). The fabrication cost of the water-permeable brick designed by the authors is only 12 US dollars/m 2 , a lower cost than the existing sand-based permeable bricks on the market. This kind of permeable brick may render substantial economic benefits and ecological improvements. The results of this study are used to present an adaptive management approach to climate change that highlights innovation, cost-efficiency, and sustainability.

water resources,engineering, civil
Nepheline‐based Water‐permeable Bricks from Coal Gangue and Aluminum Hydroxide

Xiaowen Wu,Hongrui Ma,N. J. Wu,Changhong Shi,Zhiyuan Zheng,Yafang Wang

DOI: https://doi.org/10.1002/ep.12329

IF: 2.824

2016-01-01

Environmental Progress & Sustainable Energy

Abstract:Nepheline‐based water‐permeable bricks are prepared with coal gangue and aluminum hydroxide by raw material pretreating, mixing, isostatic molding, roasting, and self‐curing. These bricks exhibit balance between their mechanical and water‐permeable properties. In this study, two main factors, the raw material ratio and the molding pressure, are studied. The mineral phase, porous structure, and mechanical properties of the samples are characterized by X‐ray diffraction, scanning electron microscopy and mercury injection, respectively. The compressive strength and water permeability of the bricks meet Chinese industry standard JC/T945‐2005 for water‐permeable bricks. The compressive strengths of the samples are between 30.6 and 34.3 MPa. The permeability coefficients range from 1.37 cm s −1 to 1.55 cm s −1 . © 2016 American Institute of Chemical Engineers Environ Prog, 35: 779–785, 2016
Microstructure Evolution and Improved Permeability of Ceramic Waste-Based Bricks

Wenfei Zhou,Huiling Du,Le Kang,Xian Du,Yupu Shi,Xiaojing Qiang,Haodong Li,Jing Zhao

DOI: https://doi.org/10.3390/ma15031130

IF: 3.4

2022-01-31

Materials

Abstract:The resource and large-scale utilization of waste ceramic materials, magnesium slag, and coal gangue are one of the important ways for the sustainable development in metallurgy, coal, and other related enterprises. In this paper, waste ceramic materials were used as aggregates; coal gangue and magnesium slag were used as mixed binder; and the all solid-waste-based permeable bricks with excellent performance were prepared by forming pressure at 5 MPa. The mechanical properties and water permeability of the all-solid-waste-based permeable bricks were evaluated. The results proved that the porous channel of permeable brick is mainly composed of waste ceramic materials with a particle size of 2–3 mm. Pore structures below 200 μm were mainly composed of fine aggregate and mixed binder. Using 60% coarse aggregate, 20% fine aggregate, 10% coal gangue, and 10% magnesium slag as raw materials, the all-solid-waste-based permeable bricks were obtained by pressing at 6 MPa and sintering at 1200 °C, which exhibited the best performance, and its water permeability, compressive strength, and apparent porosity were 1.56 × 10−2 cm/s, 35.45 MPa, and 13.15%, respectively. Excellent water permeability, compressive strength, and apparent porosity of the all solid-waste-based permeable bricks were ascribed to the high content of connecting open pores, and closely adhesive force were ascribed to the porous microstructure constructed by the grading of waste ceramic materials and the tight conjoined points of the liquid phases in coal gangue and magnesium slag at a high sintering temperature.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Utilization of Waterworks Sludge in the Production of Fired/Unfired Water Permeable Bricks

Min Xie,Dan Gao,Xiao Bo Liu,Fang Li,Cong Huang

DOI: https://doi.org/10.4028/www.scientific.net/amr.531.316

2012-01-01

Advanced Materials Research

Abstract:Waterworks sludge was used as raw material to make fired water permeable bricks (WPB) and unfired water permeable bricks (WPB). Results show that when 30% ~ 40% sludge was added with 30% ~ 35% ordinary sands ranging from 1.0 to 1.4mm and some other materials, pressed at 30 MPa and then sintered at 1150°C for 1h, the compressive strength (CS)and permeability coefficient (PC) of produced fired WPB were 36.53MPa and 1.08×10-2 cm/s respectively. When the ratio of waterworks sludge increased from 20% to 35%, the CS of the unfired WPB decreased but stayed above 20 MPa, while the change of PC is insignificant.
Relationship Between Percolation Mechanism and Pore Characteristics of Recycled Permeable Bricks Based on X-ray Computed Tomography

Songsong Lian,Tao Meng,Hongqi Song,Zhongjia Wang,Jiabin Li

DOI: https://doi.org/10.1515/rams-2021-0022

2021-01-01

REVIEWS ON ADVANCED MATERIALS SCIENCE

Abstract:The relationship between percolation mechanism and pore characteristics for recycled permeable bricks with different porosities is investigated in this study based on X-ray computed tomography (X-CT). Permeability coefficients are measured and some characteristics including size, amount, and distribution of the pore are analysed. The results show that the effective porosity and permeability coefficient of the recycled permeable bricks exhibit a linear relationship first and then a quadratic curve relationship, where the critical effective porosity is 12%. Meanwhile, we discovered that nonlinear channels in permeable bricks are larger and fewer compared with linear percolation channels, regardless of whether the percolation stage is linear or nonlinear. Additionally, when the area and number ratios of the linear and nonlinear percolation channels reached 80% and 10%, respectively, the overall percolation state of the permeable bricks changed from linear to nonlinear percolation. This research is helpful to improve the mechanical and percolation properties of recycled concrete bricks and promote the application of porous permeable material.
EXPERIMENTAL INVESTIGATION ON CONCRETE PERFORATED BRICK WALL SHINKAGE AT DIFFERENT AGES

Fu Jun,Jin Weiliang,Cui Yang,Zou Zhenli

DOI: https://doi.org/10.13204/j.gyjz2011.06.024

2011-01-01

Abstract:It is forbidden to use concrete perforated brick(CPB)wall at early ages for its big shringkage and high water content,Nevertheless,there are still many applications in engineering practice due to various reasons.Engineers should recognize their characteristics,then decide how to repair the walls.Experimental investigation is carried out in this study including bricks and walls.Firstly bricks are tested with water content,compressive strength,and etc;then whole walls at diffirent ages are tested with walls' end deformations and instantaneous strains;at last analysis and estimations are done and engineering restrictions are proposed.It is concluded that some early-age CPB bricks have wet inflations,whereas CPB walls have wet inflation and dry shrinkage circulations.Its shinkage rate is about 1.6~2.0×10-4.Walls' instantaneous strains show a pressure characreristic at beginning and then to tensile,and tend to be stable at last.Relationship between instantaneous strain and time(age)has an exponential decay trend.Results obtained in this study help engineers to control cracks and repair walls,It reflects the basic characteristics of walls at different ages,and thus has relevant engineering significance.
Preparation and characterization of majority solid waste based eco-unburned permeable bricks

Lei Liu,Xiang Cheng,Xiwang Miao,Yonglin Shi,Meixia Zhang,Min Guo,Fangqin Cheng,Mei Zhang

DOI: https://doi.org/10.1016/j.conbuildmat.2020.120400

IF: 7.4

2020-10-01

Construction and Building Materials

Abstract:In this paper, the eco-unburned permeable bricks were prepared by simulating the actual production, using steel slag as aggregates and multi-solid waste as cementitious materials. The flexural strength, water permeability coefficient, leaching toxicity and environmental sustainability of permeable bricks were determined. The prepared permeable bricks with a size of 200*100*50 mm and an average weight of 2.15 kg had a flexural strength of 4.5 MPa and a water permeability coefficient of 10.5 × 10-2 cm/s. The solid waste utilization rate reached as high as 96%. The partial f-CaO in steel slag particles was effectively digested and the remaining content was only 2.11% by controlling the curing conditions properly. The results of leaching toxicity test confirmed that the unburned permeable brick will not cause secondary pollution. Compared with the permeable bricks prepared from original materials, the SUB-RAW index of the eco-unburned permeable bricks reached 0.303, proving that it was beneficial to the environment. Therefore, the steel slag based eco-unburned permeable bricks developed in this paper can be used in industrial scale production and have broad application prospects.

construction & building technology,materials science, multidisciplinary,engineering, civil
Preparation and characterization of permeable bricks from gangue and tailings

Mengguang Zhu,Hao Wang,LiLi Liu,Ru Ji,Xidong Wang

DOI: https://doi.org/10.1016/j.conbuildmat.2017.05.096

IF: 7.4

2017-01-01

Construction and Building Materials

Abstract:•New permeable bricks were prepared by using gangue and tailings.•Effects of adding new aggregate and sintering temperature were investigated.•Effects of aggregates content and aggregates size were also investigated.•Fabrication was simplified without using natural clay and artificial aggregates.
Preparation of Ecology Water Penetrable Brick Using Siliconmanganese Slag

Jian Cao

2007-01-01

Abstract:Ecology water penetrable brick was prepared taking siliconmanganese slag as main raw material and mixed with clay and diatomite to make basic body then adding pore forming agent. The affect of burden composition and manufacturing process on performance of the brick were discussed and analyzed. The result of experiments indicates that the performance of ecology water penetrable brick which is up to the index of standard JC/T 945-2005 Water Permeable Brick can be attained by adopting reasonable formulation and manufacturing process. This not only solves the problem of environmental pollution, but also gets some economic and social benefit.
Pervious Concrete with Secondarily Recycled Low-Quality Brick-Concrete Demolition Residue: Engineering Performances, Multi-Scale/phase Structure and Sustainability

Nidu Jike,Chengji Xu,Rijiao Yang,Yuxuan Qi,Yuqing Dai,Yu Peng,Jiyang Wang,Mingzhong Zhang,Qiang Zeng

DOI: https://doi.org/10.1016/j.jclepro.2022.130929

IF: 11.1

2022-01-01

Journal of Cleaner Production

Abstract:Brick-concrete demolition residue after the primary recycling is generally discarded due to its low quality. Secondary recycling of the brick-concrete demolition residue is urgently required to be solved at present in China due to the large scale constructions and demolitions, and remains a challenging task. In this work, a brick concrete demolition residue from an urban-fringe of Hangzhou, China, was secondarily recycled as the fine aggregate to fabricate sustainable pervious concrete after systematic characterization of its physical and chemical properties. In order to improve the engineering properties of the pervious concrete, natural aggregate and sand were used. Multi-scale structure in terms of pore size distribution, skeleton morphology, and matrix-aggregate interfacial transition zone were systematically characterized using X-ray computed tomography and back scattered electron imaging tests. Results show that the increase of the natural aggregate replacement ratio and sand ratio always increases the compressive strength and density, but decrease the water permeability. Incorporation of the secondary brick-concrete demolition residue in concrete increases the total porosity and connected porosity of the pervious concrete, and helps form a Calcium-enriched matrix-aggregate interfacial layer zone. Use of the secondarily recycled brick-concrete demolition residue in pervious concrete manufacture at the optimal mix brings the CO2 emissions reduction by 107 kg/m(3) and costs reduction by 30.3 USD/m(3). The findings of this work provide a sustainable route to secondarily recycle low-quality brick-concrete demolition residue for constructions.
RAINWATER RUNOFF POLLUTANT REMOVAL EXPERIMENT USING A CERAMIC PERMEABLE BRICK SYSTEM WITH A FRAME STRUCTURE BASE

Hai Yang,Zizeng Lin,Xin Huang,Qiusheng Jia,Yuliang Li,Yuanyuan Liu,Huiming Chen

2019-01-01

Fresenius environmental bulletin

Abstract:To increase pollution removal by the base layer and further improve the water quality of effluent, a ceramic permeable brick and three typical fillers were applied to construct a frame structure brick paving system for the removal of pollutants. Initial and final measurements for contaminants such as SS, TP, NH3-N, TN, COD, and heavy metals were taken in column experiments. The results demonstrated that the ceramic permeable brick had a good mitigation effect on SS, TP, Zn, Cu and Pb and a relatively poor mitigation effect on COD, NH3-N and TN. The mitigation effects on SS, TP, NH3-N, TN, COD, Zn, Cu, and Pb in the brick paving system filled with small particle-sized gravel were 10.52%, 8.97%, 2.00%, 1.17%, 3.22%, 8.88%, 6.05%, and 8.83% greater, respectively, than the effect with large particles-sized gravel. The mitigation effects on SS, TP, NH3-N, TN, COD, Zn, Cu, and Pb in the brick paving system filled with zeolite were 7.78%, 12.28%, 16.03%, 8.72%, 13.15%, 11.17%, 9.27% and 11.92% greater, respectively, than the effect with gravel of the same diameter. These results occurred mainly because the small particle-sized gravel layer was more compact, rendering it more conducive to the filtration and retention of pollutants. Additionally, the zeolite enhanced the removal of rainwater runoff pollutants through adsorption.
A Comparative Study on Hygric Properties and Compressive Strength of Ceramic Bricks

Piotr Stępień,Edyta Spychał,Karol Skowera

DOI: https://doi.org/10.3390/ma15217820

IF: 3.4

2022-11-06

Materials

Abstract:This article analyzes the results of capillary rise, compressive strength and water absorption tests on solid ceramic bricks from existing structures and demolition materials taken from 11 different structures. In addition (for more extensive interpretation and evaluation of porosity), tests were performed for the selected series of bricks using a mercury porosimeter (MIP) and a micro computed tomography (micro-CT). Contemporary bricks (2 series) were also evaluated for comparison purposes. The conducted tests indicate that bricks obtained from different sources are characterized by "individual" relation of compressive strength and porosity, and "individual" relation of water absorption coefficient and porosity. In addition, on the basis of the results obtained in the study, compared with the literature data, it can be deduced that ceramic bricks with a water absorption coefficient of less than 50 g/m2s0.5 are characterized by a compressive strength of more than 80 MPa. As the research shows, the properties of bricks even from a single building can differ one from another, which can result in varying durability even within a single building. When choosing a material during the renovation or restoration of facilities, it is important to perform tests on the physical and mechanical properties of the original material, which will be reused.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Review of Solid Waste Resource Utilization for Brick-making

Haoran Ge,Jiyong Zhang,Zuoan Wu,A.-S. Nizami,Z.B. Daud

DOI: https://doi.org/10.1051/e3sconf/202452002006

2024-05-03

E3S Web of Conferences

Abstract:The utilization of solid waste resources is an essential strategy in the pursuit of sustainable development. Among the various techniques used for solid waste treatment, brick-making technology stands out as a key approach to facilitate the utilization of solid waste resources. This article provides a comprehensive review and summary of the recent research progress in the field of solid waste resource utilization for brick-making. It mainly focuses on the current state and technological advancements in brick-making using solid waste. Considering the influence of different external factors and variations in brick-making raw materials, this study employs the Citespace software to conduct co-word and clustering analysis, with "resource utilization" as the primary keyword. Furthermore, it introduces the brick-making technology utilizing sludge and red mud as raw materials, while also elaborating on advanced techniques and practical experiences in utilizing industrial and urban solid waste as raw materials. Additionally, the article presents an overview of the key development trends in this field and puts forward several recommendations for future research to aid designers in furthering their investigation.
Effect of Moisture Condition of Brick–Concrete Recycled Coarse Aggregate on the Properties of Concrete

Yonghua Wu,Zhaodong Qi,Mengdie Niu,Yuan Yao,Zuoqiu Luo,Kaifeng Zhang

DOI: https://doi.org/10.3390/ma15207204

IF: 3.4

2022-10-16

Materials

Abstract:The application of brick–concrete recycled aggregates can alleviate the problem of increasing construction waste and increasing scarcity of natural aggregates. The different moisture condition of coarse aggregates can significantly affect the performance of brick–concrete recycled aggregate concrete. In this paper, the additional water quantity of dry and air-dried brick–concrete recycled coarse aggregate concrete was determined. Additionally, the fluidity, rheological parameters, autogenous shrinkage, strength and chloride ion penetration resistance were tested, and compared with saturated surface dry recycled brick–concrete coarse aggregate concrete and natural aggregate concrete. The results showed that the slump of concrete was increased, whereas the plastic viscosity, static and dynamic yield stress were decreased by adding additional water or using saturated surface dry coarse aggregate. Compared with the dry and saturated surface dry state, the air-dried recycled coarse aggregate concrete has the smallest 28 days autogenous shrinkage value, higher compressive strength and splitting tensile strength, and less adverse effects on chloride permeability. It is most beneficial to the performance and economy of concrete to adopt the air-dried state when the brick–concrete recycled coarse aggregate is applied in engineering.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Using water-based drilling cuttings from shale gas development to manufacture sintered bricks: a case study in the southern Sichuan Basin, China

Wenshi Liu,Hui Yuan,Zhenzhen Fan,Jing Li,Lingru Sun

DOI: https://doi.org/10.1007/s11356-021-12847-4

Abstract:Large amounts of water-based drilling cuttings (WDC) would be generated during the drilling of shale gas wells, which would occupy land resources and pose significant threat to soil and groundwater environment. The aim of this study was to assess the feasibility of using WDC as a replacement of natural clay to prepare sintered bricks. To determine the optimum preparation condition, the weight loss on ignition, bulk density, water absorption, and compressive strength of the samples were tested. Meanwhile, the environmental performance of the final products was evaluated and micro-analysis was conducted via X-ray diffraction and scanning electron microscopy. The results showed that using WDC to manufacture sintered bricks was technically feasible, but the physical mechanical performance would significantly decrease with the increase of the replacement ratio because of the presence of less silica and excessive calcium. The addition of waste glass and fly ash could promote the generation of molten glassy phase and form the crystal particle bonding structure, which would contribute to the physical-mechanical performance of WDC sintered bricks. Some mineral components in raw materials decomposed and formed minerals with better thermal stability during the sintering process. Under the optimum preparation conditions (mass ratio of WDC: waste glass: fly ash at 40:20:40, sintering temperature at 900 °C, and insulation time at 2 h), the physical-mechanical and environmental performance of WDC sintered bricks could meet the requirements of corresponding Chinese standards and ASTM standards. Thus, in this study, an effective solution to recycle WDC from shale gas development is provided.

The current situation and prospects of water-permeable brick

Research on the performance of sand-based environmental-friendly water permeable bricks

ANALYSIS OF THE INFLUENCE OF PROCESS CONDITIONS ON THE PERFORMANCE OF ENVIRONMENT-FRIENDLY PERVIOUS BRICK

The Performance Characteristics of Sand Wall-like Architectural Coatings and Construction Technology for Imitation Exterior Wall Brick

Preparation of Permeable Paving Bricks via Geopolymeric Method

Decontamination performance and cleaning characteristics of three common used paved permeable bricks

Rainwater Harvest with Desert-Sand Bricks: An Adaptive Water Resources Management Strategy for Climate Change

Nepheline‐based Water‐permeable Bricks from Coal Gangue and Aluminum Hydroxide

Microstructure Evolution and Improved Permeability of Ceramic Waste-Based Bricks

Utilization of Waterworks Sludge in the Production of Fired/Unfired Water Permeable Bricks

Relationship Between Percolation Mechanism and Pore Characteristics of Recycled Permeable Bricks Based on X-ray Computed Tomography

EXPERIMENTAL INVESTIGATION ON CONCRETE PERFORATED BRICK WALL SHINKAGE AT DIFFERENT AGES

Preparation and characterization of majority solid waste based eco-unburned permeable bricks

Preparation and characterization of permeable bricks from gangue and tailings

Preparation of Ecology Water Penetrable Brick Using Siliconmanganese Slag

Pervious Concrete with Secondarily Recycled Low-Quality Brick-Concrete Demolition Residue: Engineering Performances, Multi-Scale/phase Structure and Sustainability

RAINWATER RUNOFF POLLUTANT REMOVAL EXPERIMENT USING A CERAMIC PERMEABLE BRICK SYSTEM WITH A FRAME STRUCTURE BASE

A Comparative Study on Hygric Properties and Compressive Strength of Ceramic Bricks

Review of Solid Waste Resource Utilization for Brick-making

Effect of Moisture Condition of Brick–Concrete Recycled Coarse Aggregate on the Properties of Concrete

Using water-based drilling cuttings from shale gas development to manufacture sintered bricks: a case study in the southern Sichuan Basin, China