Abstract:The structure, morphology, and mechanical properties of two compression-molded grades of ultrahigh-molecular-weight polyethylene (UHMWPE) and, for comparison, one conventional linear polyethylene (HDPE) were studied. Compression molding resulted in some preferred orientation of lamellae in the compression direction in UHMWPE samples, while no preferred orientation in HDPE. The mean crystal thickness estimated from the size distribution agrees better with those obtained from small-angle X-ray scattering (SAXS) and mechanical yield data than the thickness determined from the melting peak temperature. Microscopic examination of microtomed and etched UHMWPE samples showed that the lamellae are in the form of platelets with the width and length in the range of 300-700 nm. The lamellae radiate from primary nuclei forming small embryonal spherulites; their radial growth ends at 0.3-0.7 μm from the center. There is no evidence of branching and secondary nucleation from those primary lamellae. Because the lamellae are radially ordered, there is no parallel stacking of lamellae. Samples were subjected to deformation by plane-strain compression at a constant true strain rate. In axial UHMWPE samples, where lamellae were preferentially oriented along the loading direction, the second yield was clearly observed. The second yield was found to be related to the deformation instability leading to kinking of lamellae oriented initially along the loading direction. Kinking was clearly shown by SAXS and microscopic observation of microtomed and etched samples. No cooperativity of kinking was observed because the lamellae are arranged in small spherulites and not parallel in stacks. The stress-strain curves were fitted with model curves assuming crystal plasticity and network elasticity in the amorphous component. The effective density of the molecular network within the amorphous phase depended on the molecular weight of UHMWPE.

Quasi-static and dynamic nanoindentation studies on highly crosslinked ultra-high-molecular-weight polyethylene.

Experimental Measurement of Polyethylene Chain Modulus by Scanning Force Microscopy

A Crosslinking Method of UHMWPE Irradiated by Electron Beam Using TMPTMA As Radiosensitizer

Nanostructure and Mechanical Measurement of Highly Oriented Lamellae of Melt-Drawn HDPE by Scanning Probe Microscopy

Impact resistance and fractography in ultra high molecular weight polyethylenes

Effect of gamma ray irradiation on processability and properties of ultra high molecular weight polyethylene

Segmental Orientations and Deformation Mechanism of Poly(Ether-Block-Amide) Films

Study on tribological properties of UHMWPE irradiated by electron beam with TMPTMA and TPGDA as crosslinking agents

Inverse Temperature Dependence of Strain Hardening in Ultrahigh Molecular Weight Polyethylene: Role of Lamellar Coupling and Entanglement Density

Tribological Properties and Structure of Ultra-High Molecular Weight Polyethylene after Gamma Irradiation

Irradiation crosslinking of ultra-high molecular weight polyethylene

The Influence of Irradiation Dose on Mechanical Properties and Wear Resistance of Molded and Extruded Ultra High Molecular Weight Polyethylene.

Effect of crosslinking, remelting, and aging on UHMWPE damage in a linear experimental wear model

Effect of Irradiation Dose on Plastic Deformation of Vacuum Hot Pressed Ultra High Molecular Weight Polyethylene

Tribological Properties of γ-ray Irradiation Cross-linked Ultra High Molecular Weight Polyethylene

Improving Wear Resistance of Ultrahigh Molecular Weight Polyethylene:Cross-linking Versus Crystallinity

Uniaxial cyclic deformation and internal heat production of ultra-high molecular weight polyethylene

Study of deformation behavior of ultra-high molecular weight polyethylene (UHMWPE)

Simultaneously Improving Wear Resistance and Mechanical Performance of Ultrahigh Molecular Weight Polyethylene Via Cross-Linking and Structural Manipulation

Morphology and Plastic Yielding of Ultrahigh Molecular Weight Polyethylene

Structure Evolution During Uniaxial Tensile Deformation of High Density Polyethylene Before and after Irradiation by 1 MeV Electrons