Abstract:Objective: This study aims to analyse the influence of different lining material, thickness and coverage on residual stress of class II molar restoration by the multilayer technique through the three-dimensional (3D) finite element (FE) method. The objective is to reveal the correlations between the base layer configurations and the residual stress distributions of the tooth. Methods: A 3D reconstructed model of an extracted first molar was built through micro-CT images and a class II mesio-occlusal-distal cavity was prepared using computer-aided engineering (CAE) software. A bilayer technique was then applied, and 3D FE analyses were performed under polymerization contraction loading. Glass ionomer composites (Vitrebond and Ionosit) and flowable composite resin (Luxa Flow and Z350 Flowable Restorative) were used as lining materials. Moreover, several sensitivity analyses with dozens of hypothetical lining materials were conducted to provide definitive results. The thickness of the base layers was set to be distinct (0.5 mm or 1 mm) so as to reveal its effect on the stress alleviation. Various lining strategies with the liner covering different areas of the cavity walls (Closed Sandwich, Open Sandwich and Special Open Sandwich) were adopted to determine the effects of the base layers. Results: Adoption of an appropriate liner could effectively reduce the polymerization shrinkage stress. The mechanical properties of the base layer can affect the residual stresses, basically a lower Young's modulus and lower Poisson's ratio (of lining material) result in better stress mitigation, therefore reducing the stress transmitted to the dentin. Increase of the lining thickness within a certain range could lead to a decrease in the probability of stress concentration formation. Lining strategies had the strongest influence on the stress distributions. Different lining coverage could cause various stress responses, and covering all cavity walls with the lining material had the optimal performance among all the simulations in this study. Significance: The multilayer technique is an effective way to prolong the service life of resin composites restorations. A thorough evaluation of the sandwich technique through the FE method can provide a better understanding of the stress distributions of the restoration, and reveal its internal mechanisms.

Histological evaluation of three commonly used light-cured resin composite materials in the wedge-shaped defect repair of extracted teeth

Evaluation of three repair methods for wedge shaped defects

Three-dimensional Finite Element Stress Analysis of First Mandibular Premolar Restored by Different Materials under Loading

Clinical trial of restoration of deep dental wedge-shaped defects with three different methods

Three-dimensional finite element analysis of severe wedge-shaped defective premolar restored with fiber post and composite resin

Effects of the lining material, thickness and coverage on residual stress of class II molar restorations by multilayer technique

Comparative study on three resin cements to restore anterior flared roots

The Clinical Curative Analysis of 3M FiltekTMZ350 XT for Repairing Moderate and Severe Dental Fluorosis Wedge-Shaped Defect

Comparative study of three composite materials in bonding attachments for clear aligners

Early clinical effect of FiltekTM Z350 flowable nanocomposite in restoring dental wedge-shaped defects

Study on the fracture-resistant forces of premolars with wedge-shaped defects post restoration

Effectiveness of different resin composite materials for repairing noncarious amalgam margin defects

Finite Element Stress Analysis of Three Filling Techniques for Class V Light-cured Composite Restorations

Comparing Marginal Microleakage of Three Different Dental Materials in Veneer Restoration Using a Stereomicroscope: an in Vitro Study.

Comparation of the Clinical Effects of Glass Ionomer Cement and Flowable Composite Resin on the Restoration of Dental Wedge-Shaped Defects

[Clinical Evaluation of Gingival Composite Resin Restoring Cervical Defects in Anterior Teeth].

Fiber post-core restoration for three types of incisor crown defects: Finite element analysis of stress

Evaluation of the clinical curative effect and influence factors of F_(2000) Compomer with different adhesive agent for restoration of dental wedge-shaped defects

Mechanical Behavior of Repaired Monolithic Crowns: A 3D Finite Element Analysis

A Comparative Study of the Repair Bond Strength of New Self-Adhesive Restorative Materials With a Resin Composite Material

Fracture resistance ability of severe wedge-shaped premolar defects restored with fiber reinforced composite post by different methods