Abstract:Using hydroxypropyl terminated polydimethylsiloxane ( HP. PDMS ), isophorone diisocyanate and 2,2-bis( hydroxymethyl ) butyric acid as starting materials, silicone-polyurethane copolymer ( Si-PU ) latexes with particle diameter of about 50 nm were prepared via step-by-step feeding process followed by phase inversion technique in the absence of surfactant. Influences of the HP-PDMS content on the phase structure and the properties of the Si-PU latex films were investigated, and the difference between Si-PU and polyether polyurethane ( E-PU ) was emphasized. It was found that the content of PDMS in Si-PU could reach up to 65 wt%. Results of DSC analysis showed that, in comparison with the E-PU latex film, the Si-PU latex films exhibited well phase separation. Strong hydrogen bonding in Si-PU hard segments was confirmed by FTIR, which promoted the micro. phase separation in the latex films. On the contrary, strong hydrogen bonding existed in between the soft and hard segments in E-PU, which led to phase mixing and prevented the formation of phase separation structure. The Si-PU latex films were characterized by AFM tapping mode and the formation of sea. island phase separation was observed, and this kind of phase separation structure in the Si-PU latex films was rarely reported in the literature, in which the amorphous PDMS. enriched domains constituted the dispersed phases. With the increase in HP. PDMS content, the degree of phase separation in the Si-PU latex films increased as well, which led to the decrease of elastic modulus from 400.0 MPa to 32.2 MPa with an increase in elongation at break and in the flexibility. The initial decomposition temperature of the Si-PU latex films was at about 244 degrees C, which was 18 degrees C lower than that of the E-PU latex film due to the low degree of hydrogen bonding between the soft and the hard segments, whereas the thermal stability of Si-PU at high temperature zone was much better than E-PU. Compare to the E-PU latex film, a low water adsorption rate under 11% and a high contact angle above 94 degrees indicated excellent water resistance of the Si-PU latex films.

Emulsification of polyisoprene rubber and stability of emulsion

Stability of the emulsion copolymerization process of the latex containing glycidyl and amino groups

Phase inversion during bulk copolymerization of N-phenylmaleimide/styrene in presence of polybutadiene (II): Effects of operation conditions and recipes on occurrence of phase inversion and structure of rubber phase

Study on Silicone Modified Polyurethane-Acrylate Copolymer Emulstion

Simultaneous Interpenetrating Polymer Networks of Polyurethane from Pentaerythritol–Modified Castor Oil and Polystyrene: Structure–Property Relationships

Stability of Surfactant-Free High Internal Phase Emulsions and Its Tailoring Morphology of Porous Polymers Based on the Emulsions

Emulsification of Modified Petroleum Waxes

Stability of High Internal Phase Emulsions with Sole Cationic Surfactant and Its Tailoring Morphology of Porous Polymers Based on the Emulsions

Stability and optimum polymerized condition of polysiloxane-polyacrylate core/shell polymer

Synthesis of Latex Particles with a Complex Structure As an Emulsifier of Pickering High Internal Phase Emulsions

Tailoring stability in oil-in-water high internal phase Pickering emulsions (HIPPEs) through surface modification of beeswax-based solid lipid particles (SLPs) with various surfactants

Synthesis and characterization of polyHIPEs using a polymerizable polyurethane macromolecular surfactant

Investigation on the Preparation of Silicone-polyurethane Latex, Phase Structure and Property of the Latex Films

Emulsifying capacity of peanut polysaccharide: Improving interfacial property through the co-dissolution of protein during extraction

Emulsions stabilized by asphaltene-polyacrylamide-soil three-phase components: Stabilization mechanism and concentration effects

Effect of oil type on stability of high internal phase water-in-oil emulsions with super-cooled internal phase

Effect of amphiphilic nanoparticles and non-ionic surfactants on emulsion stability

AN INVESTIGATION OF THE STABILITY AND LUBRICITY OF EMULSIONS FOR STRIP COLD ROLLING

Influence of Liquid Isoprene on Rheological Behavior and Mechanical Properties of Polyisoprene Rubber

Enhanced Stability of the Dispersed Phase Stabilized by Polyether-Modified Siloxane in the Double Emulsion System: Storage Stability and Rheological Investigation

Synergistic Stabilization and Tunable Structures of Pickering High Internal Phase Emulsions by Nanoparticles and Surfactants