Adsorption of hydrogen on porous materials of activated carbon and zeolite NaX crossover critical temperature

Jing Li,Erdong Wu

DOI: https://doi.org/10.1016/j.supflu.2008.12.015

IF: 3.9

2009-01-01

The Journal of Supercritical Fluids

Abstract:Hydrogen adsorptions of activated carbon and zeolite NaX are studied through isotherm measurements crossover critical temperature. Some unique adsorption features are observed and explained.

What problem does this paper attempt to address?

Cryoadsorption of Hydrogen on Divalent Cation-Exchanged X-zeolites

Jing Li,Erdong Wu,Jiangwei Song,Fengshou Xiao,Changjian Geng

DOI: https://doi.org/10.1016/j.ijhydene.2009.04.047

IF: 7.2

2009-01-01

International Journal of Hydrogen Energy

Abstract:The cryoadsorption of hydrogen on divalent cation-exchanged zeolites and its relation with exchanged ions is investigated by volume measurements performed at near critical temperatures of 140–35K and pressures up to 7MPa. The hydrogen uptakes of the zeolites follow an order of NaX>MgX>ZnX>NiX, as same as that of the stability of the ions, but opposite to the hydration tendency of the ions and the isosteric heat of the adsorption of the zeolites, which indicate that the redox potential of the ions in the zeolite is a dominant factor in hydrogen adsorption. The drop of excess adsorption to negative amount and the following recovery at near critical temperature and pressure are explained by a reversed effect of capillary condensation and the bias of the compressibility factor from the assumed equation of state.
STUDY ON THE ADSORPTION CHARACTERISTIC OF HYDROGEN ON THE ACTIVATED CARBON AT LOW TEMPERATURES

Qingrong Zheng,Anzhong Gu,Xuesheng Lu,Wensheng Lin

DOI: https://doi.org/10.3321/j.issn:0254-0096.2008.05.021

2008-01-01

Abstract:Based on an approximate adsorption model developed from lattice theory, adsorption data at temperature range 78-173K of hydrogen upon activated carbons were selected to comparatively study the behaviors of hydrogen molecules. The maximum concentration of hydrogen molecules upon the activated carbon surface was determined by the linearization of the model on the adsorption data. The results showed that the maximum surface concentration is lower than that of the liquid hydrogen and decreased with increasing temperature. In the initial adsorption state, the molecular interaction energy among hydrogen molecules is larger on the activated carbon with a small specific surface area and pore volume due to its less space for accumulation of hydrogen molecules. With the increasing of the adsorption amount, the interaction energy among hydrogen molecules adsorbed on the activated carbon having a higher specific surface area and pore volume would increase much rapidly. Conclusions were also drawn that special design of the activated carbon should be made to improve its hydrogen adsorption capacity.
Micro-channel Development and Hydrogen Adsorption Properties in Templated Microporous Carbons Containing Platinum Nanoparticles

Yunxia Yang,Craig M. Brown,Chunxia Zhao,Alan L. Chaffee,Burke Nick,Dongyuan Zhao,Paul A. Webley,Jacob Schalch,Jason M. Simmons,Yun Liu,Jae-Hyuk Her,C. E. Buckley,Drew A. Sheppard

DOI: https://doi.org/10.1016/j.carbon.2010.11.050

IF: 10.9

2011-01-01

Carbon

Abstract:Ordered microporous carbons containing dispersed platinum nanoparticles were fabricated and chosen as suitable models to investigate micro-structure development and hydrogen transport properties of zeolite-templated carbons. X-ray photoelectron spectroscopy analysis revealed that the enhanced heat of adsorption is related to the narrow micro-channels templated from the zeolite and the presence of certain CO groups on the carbon. The lack of a well-defined and intense rotational transition line and the persistent broad H2 recoil spectrum in neutron scattering results suggests a distribution of binding sites. Most interestingly, hydrogen diffusion occurs on two time scales, consisting of a fast liquid-like jump diffusion on the timescale of picoseconds along with an even faster bulk-like diffusion. The liquid-like motion is characterized by a diffusion constant of (2.1±0.3)×10−8m2/s with an activation energy of ca. 77K; both values indicate somewhat lower mobility than similar dynamics of H2 on nanotubes, activated carbon XC-72, or Grafoil, yet greater mobility than that of bulk liquid. These unusual characteristics for hydrogen in carbons are believed to arise from the network of narrow pores in this zeolite-templated image of the zeolite. In fact, the diffusion constants of the templated carbons are extremely similar to those measured for zeolite 13X.
A Linear Comprehensive Adsorption Model of Hydrogen on Super Activated Carbon under Supercritical Conditions

L Zhan,KX Li,YL Wang,QH Meng,CX Lv,LC Ling

DOI: https://doi.org/10.1006/jcis.2002.8275

IF: 9.9

2002-01-01

Journal of Colloid and Interface Science

Abstract:The adsorption isotherms of hydrogen on super activated carbon were measured systematically, covering a temperature range of 93-293 K at 20 K intervals and pressures up to 7 MPa. All the experimental data were linearized by adopting the coordinates ln ln(n) vs 1/(ln P). The results indicate that the adsorption limit (P(lim), n(lim)) exists virtually at high pressure and has a certain physical meaning. Based on the adsorption limit, further analyses were carried out by modeling the adsorption isotherms in the coordinates ln(n(lim)/n) vs ln(RT(ln(P(lim)/P) and a linear comprehensive adsorption model was proposed in the form n (lim)=n.exp(psi T+lambda/T-c/) (beta).[RT ln( P (lim)P )] (b) which can predict the adsorption isotherm of hydrogen on activated carbon in supercritical conditions.
Enhanced CO2 Adsorption Performance on Hierarchical Porous ZSM-5 Zeolite

Qing Liu,Pingping He,Xingchi Qian,Zhaoyang Fei,Zhuxiu Zhang,Xian Chen,Jihai Tang,Mifen Cui,Xu Qiao,Yao Shi

DOI: https://doi.org/10.1021/acs.energyfuels.7b02543

IF: 4.6541

2017-01-01

Energy & Fuels

Abstract:Hierarchical porous ZSM-5 (HP-ZSM-5) was constructed using organosilanes as the growth inhibitors for CO2 capture. The properties of adsorbents were characterized by X-ray diffraction, N-2 adsorption/desorption, scanning electron microscopy, temperature-programmed desorption of carbon dioxide, and Al-27 magic angle spinning nuclear magnetic resonance. It was found that HP-ZSM-5 samples synthesized by organosilanes had a significant effect on the microstructure and morphology. CO, adsorption capacity of HP-ZSM-5 was up to 58.26 cm(3) g(-1) at 0 degrees C and 1 bar, significantly higher than that of the ZSM-5 sample. The effective improvement of CO2 adsorption performance mainly originated from the micro-/mesoporous composite structure and complex surface morphology, which can provide low -resistant pathways for CO2 through the porous network. Besides, in situ Fourier transform infrared spectroscopy was carried out to study the adsorption process on adsorbents, and the results indicated that a faster physical adsorption process was achieved as a result of the introduction of mesopores.
Adsorption separation of carbon dioxide, methane, and nitrogen on Hβ and Na-exchanged β-zeolite

Xiaoliang Xu,Xingxiang Zhao,Linbing Sun,Xiaoqin Liu

DOI: https://doi.org/10.1016/s1003-9953(09)60015-3

2008-12-01

Journal of Natural Gas Chemistry

Abstract:Adsorption isotherms of carbon dioxide (CO2), methane (CH4), and nitrogen (N2) on Hβ and sodium exchanged β-zeolite (Naβ) were volumetrically measured at 273 and 303 K. The results show that all isotherms were of Brunauer type I and well correlated with Langmuir-Freundlich model. After sodium ions exchange, the adsorption amounts of three adsorbates increased, while the increase magnitude of CO2 adsorption capacity was much higher than that of CH4 and N2. The selectivities of CO2 over CH4 and CO2 over N2 enhanced after sodium exchange. Also, the initial heat of adsorption data implied a stronger interaction of CO2 molecules with Na+ ions in Naβ. These results can be attributed to the larger electrostatic interaction of CO2 with extraframework cations in zeolites. However, Naβ showed a decrease in the selectivity of CH4 over N2, which can be ascribed to the moderate affinity of N2 with Naβ. The variation of isosteric heats of adsorption as a function of loading indicates that the adsorption of CO2 in Naβ presents an energetically heterogeneous profile. On the contrary, the adsorption of CH4 was found to be essentially homogeneous, which suggests the dispersion interaction between CH4 and lattice oxygen atoms, and such interaction does not depend on the exchangeable cations of zeolite.

English Else
Experimental Study and Computer Simulation of Hydrogen Adsorption on Carbon Nanofibres.

C Zhang,Guilin Zhou,Xiulin Fan

2007-01-01

Abstract:The hydrogen adsorption by carbon nanofibres has been experimentally studied together with computer simulations. Adsorption isotherms on one kind of carbon nanofibres have been volumetrically measured over a temperature range of 273-353 K. The adsorption amount is small. And the adsorption and desorption isotherms are almost reversible, which reveals the characteristics of physisorption. Grand canonical ensemble Monte Carlo approach is also used to simulate hydrogen adsorption on carbon nanofibres with different pore width. Simulated results show that it is difficult to meet the DOE target (6.4 wt%, 62.0 m3/kg) when the pore width is 0.34 nm. When the pore width is expanded to 0.9 nm, the hydrogen uptake reaches a maximum at a moderate pressure, and can meet the target under 1 MPa at 77 K. The potential energy theory is also adopted to explain the simulation results.
The Adsorption and Catalytic Cracking of C8 Hydrocarbons on HZSM-5 Zeolite

FAN Zheyong,LIU Tao,BAO Xiuxiu,FEI Jinhua

DOI: https://doi.org/10.3785/j.issn.1008-9497.2016.04.006

2016-01-01

Abstract:The performances of adsorption , desorption and catalytic cracking of several C8 hydrocarbons with different structures have been tested on HZSM‐5 zeolie .Cyclooctane was not converted on the zeolite because its molecular size was larger than the pore size of the zeolite and could not enter into the pores of the zelite .However , cyclooctene which had the similar molecular size as cyclooctane showed higher adsorption and conversion ,due to the double bond promoting via the polarity induction and acidic sites of the zeolite .Obviously ,n‐octane and n‐octene with smaller molecular size could enter into the pores of HZSM‐5 zelite and bring adsorption and conversion .There‐fore ,the adsorption and conversion of C8 hydrocarbons on HZSM‐5 zelite can be affected by their structures and properties .
Temperature dependent behavior of hydrogen molecules on carbon nanostructures

Qingrong Zheng,Anzhong Gu,Xuesheng Lu,Wensheng Lin

2004-01-01

Abstract:For studying the temperature dependent behavior of hydrogen molecules adsorbed on carbon nanostructures, hydrogen adsorption data on multi-walled carbon nanotubes (MWCNTs) were analyzed with an approximate adsorption model developed from lattice theory. The maximum surface concentration of hydrogen molecules upon the MWCNTs was determined by the linear regression on the experimental data. The interaction potential of hydrogen -MWCNTs and the isosteric heat of hydrogen adsorption in low limit surface concentration were calculated by using gas-surface virial coefficients and Henry law. We conclude that hydrogen molecules physically accumulate mostly in a place where the potential was at a minimum within the central tubular pore of the MWCNTs and are likely in a state of the compressed gas; significant adsorption of hydrogen molecules does not occur on the MWCNTs, neither does the temperature dependent hydrogen-hydrogen interaction energy show an optimum temperature region for hydrogen storage by adsorption on the MWCNTs.
The comparison of adsorption characteristics of CO2/H2O and N2/H2O on activated carbon, activated alumina, zeolite 3A and 13X

Junhui Lu,Jinjing Tang,Junming Li,Suilin Wang

DOI: https://doi.org/10.1016/j.applthermaleng.2022.118746

IF: 6.4

2022-01-01

Applied Thermal Engineering

Abstract:•The adsorption of CO2/H2O and N2/H2O is compared by dynamic experiments.•Effects of flow rate, temperature and steam mole fraction are analyzed.•Activated carbon and activated alumina, zeolite 3A and 13X are compared.•CO2/H2O adsorption selectivity ranked as: 3A> 13X> alumina> activated carbon.•The thermal wave peak of N2/H2O is decayed and delayed comparing to CO2/H2O.
Characterisation of porous hydrogen storage materials: carbons, zeolites, MOFs and PIMs

Steven Tedds,Allan Walton,Darren P Broom,David Book

DOI: https://doi.org/10.1039/c0fd00022a

Abstract:Porous materials adsorb H2 through physisorption, a process which typically has a rather low enthalpy of adsorption (e.g. ca. 4 to 7 kJ mol(-1) for MOFs), thus requiring cryogenic temperatures for hydrogen storage. In this paper, we consider some of the issues associated with the accurate characterisation of the hydrogen adsorption properties of microporous materials. We present comparative gravimetric hydrogen sorption data over a range of temperatures for different microporous materials including an activated carbon, a zeolite, two MOFs and a microporous organic polymer. Hydrogen adsorption isotherms were used to calculate the enthalpy of adsorption as a function of hydrogen uptake, and to monitor the temperature dependence of the uptake of hydrogen. Under the conditions investigated, it was found that the Tóth equation provided better fits to the absolute isotherms compared to the Sips (Langmuir-Freundlich) equation at low pressures, whereas it appeared to overestimate the maximum saturation capacity. The isosteric enthalpy of adsorption was calculated by either: fitting the Sips and Tóth equations to the adsorption isotherms and then applying the Clausius-Clapeyron equation; or by using a multiparameter Virial-type adsorption isotherm equation. It was found that the calculated enthalpy of adsorption depended strongly upon the method employed and the temperature and pressure range used. It is shown that a usable capacity can be calculated from the variable temperature isotherms for all materials by defining a working pressure range (e.g. 2 to 15 bar) over which the material will be used.
The Prediction of the Adsorption of Hydrogen within the Slit-pores of Carbon Micro-pore Adsorbents

郑青榕,顾安忠,杨晓东,林文胜,鲁雪生

DOI: https://doi.org/10.3969/j.issn.1674-0068.2001.06.007

IF: 1.09

2001-01-01

Chinese Journal of Chemical Physics

Abstract:The Ono - Kondo isotherm equation for the hydrogen molecules adsorbed within the slit - pores of the carbon micro - pore adsorbents is deduced by the mean - field approximations to the adsorption boundary. Then the maximum adsorption capacities at two typical kinds of stacking of the hydrogen molecules upon the graphite surface arc valued by using the characteristics of the lattice gas model and the theory of Microphysics. The values of other parameters for the Ono - Kondo equation at two typical stacking states of hydrogen molecules are obtained by using the ascertained maxi-mum adsorption capacities, the langmuir calibration and the linear regression on the experimental data. The predicted precision of the two equations is evaluated by the mean relative error between the predicted results and the experimental data, and the equation ascertained by the close - packing of hydrogen molecules with the higher accuracy is applied to predict the adsorption isotherm under the same condition described in literatures. The predicted results are compare with the experimental data and those from the GCMC molecular simulation under the same adsorption condition on the same kinds of adsorbents. Finally, the effective range of the ascertained equation is analyzed and the suggestions are given to the application of the equation.
Adsorption equilibrium isotherms and thermodynamic analysis of CH4, CO2, CO, N2 and H2 on NaY Zeolite

Li Feng,Yuanhui Shen,Tongbo Wu,Bing Liu,Donghui Zhang,Zhongli Tang

DOI: https://doi.org/10.1007/s10450-020-00205-8

2020-02-08

Adsorption

Abstract:Adsorption capacities of CH4, CO2, CO, N2 and H2 on NaY zeolite were measured at 298 K, 318 K, 338 K and 358 K with pressure ranged from 0 to 10 bar. The order of adsorption capacity was CO2 ≫ CH4 > CO > N2 ≫ H2. The experiment data were fitted by the Langmuir, Toth and Sips equations. The fitting relativity of above models were also compared. Moreover, the isosteric heat of adsorption were calculated by the Clausius–Clapeyron equation, the results showed that the adsorption heat of CO2 is the largest (41.89764 kJ/mol with adsorption loading of 5.8 mmol/g) and that of H2 is the smallest. Finally, the selectivity of binary mixture was predicted according to the IAS theory.
Adsorption of CO 2 and N 2 on Synthesized NaY Zeolite at High Temperatures

Wei Shao,Luzheng Zhang,Liangxiong Li,Robert L. Lee

DOI: https://doi.org/10.1007/s10450-009-9200-y

2009-01-01

Adsorption

Abstract:NaY zeolite particles with a high surface area of 723 m(2)/g were synthesized by a hydrothermal method. Adsorption isotherms of pure gases CO2 and N-2 on the synthesized NaY particles were measured at temperatures 303, 323, 348, 373, 398, 423, 448 and 473 K and pressures up to 100 kPa. It was found that the adsorption isotherm of CO2 on the synthesized zeolite is higher than that on other porous media reported in the literature. All measured adsorption isotherms of CO2 and N-2 were fitted to adsorption models Sips, Toth, and UNILAN in the measured temperature/pressure range and Henry's law adsorption equilibrium constants were obtained for all three adsorption models. The adsorption isotherms measured in this work suggest that the NaY zeolite may be capable of capturing CO2 from flue gas at high temperatures. In addition, isosteric heats of adsorption were calculated from these adsorption isotherms. It was found that temperature has little effect on N-2 adsorption, while it presents marked decrease for CO2 with an increase of adsorbate loading, which suggests heterogeneous interactions between CO2 and the zeolite cavity.
On the Nature of Spillover Hydrogen Species on Platinum/nitrogen-Doped Mesoporous Carbon Composites: A Temperature-Programmed Nitrobenzene Desorption Study

Fengkai Yang,Bin Hu,Wei Xia,Baoxiang Peng,Jianyi Shen,Martin Muhler

DOI: https://doi.org/10.1016/j.jcat.2018.06.020

IF: 7.3

2018-01-01

Journal of Catalysis

Abstract:Spillover hydrogen species were generated by dissociative H-2 adsorption on Pt nanoparticles supported on nitrogen-doped mesoporous carbon. The spillover hydrogen species on the support can migrate back to the Pt nanoparticles and hydrogenate subsequently adsorbed nitrobenzene to aniline at 80 degrees C, which was detected during temperature-programmed desorption experiments from 80 to 300 degrees C in pure He. The amount of spillover hydrogen can be tuned mainly by the pre-reduction temperature rather than by other parameters. The absence of aniline formation during nitrobenzene desorption experiments in the presence of CO indicates that hydrogenation occurs exclusively on Pt and that the spillover hydrogen species are present on the carbon support in a chemically inactive state. Most likely, spillover hydrogen is reversibly stored on the carbon support as adsorbed protons on the surface and as electrons in the bulk. These findings provide a new perspective on Pt/C-based hydrogen storage materials and fuel cell catalysts. (C) 2018 Elsevier Inc. All rights reserved.
Adsorption and diffusion of n-heptane and toluene over mesostructured ZSM-5 zeolitic materials with acidic sites

Duo Xu,Jinghong Ma,He Zhao,Zhiping Liu,Ruifeng Li

DOI: https://doi.org/10.1016/j.fluid.2016.04.013

IF: 2.745

2016-09-01

Fluid Phase Equilibria

Abstract:In order to understand the effects of the surface acid sites in mesoporous zeolites on the adsorption and diffusion of hydrocarbons, the adsorption and diffusion of n-heptane and toluene (two C7 hydrocarbons) over the mesoporous HZSM-5 zeolites (SiO2/Al2O3 = 36) were investigated. The adsorption isotherms of two C7 hydrocarbons over the mesoporous HZSM-5 zeolites showed the experimental data good fitting to dual-site Langmuir-Freundlich model (DSLF) similar to mesoporous NaZSM-5. Henry's constants and the initial heats of adsorption displayed stronger interactions in HZSM-5 than in NaZSM-5, especially for n-heptane, due to the presence of surface acid sites. The influence of acidity to the adsorbate-adsorbent interactions decreases with increasing of the mesoporosity. The investigation on the diffusion of n-heptane and toluene in mesoporous HZSM-5 samples by the zero-length column (ZLC) method showed the strong interaction of adsorbates and HZSM-5 samples by effective diffusivity and activation energy. Moreover, the diffusions of adsorbates in zeolites were advanced with the introduction of mesopores in the zeolitic samples, though the dramatic influence of mesopore to diffusion is not arisen in mesoporous NaZSM-5, reflecting larger influence of acid sites on diffusion in mesoporous HZSM-5 samples.

engineering, chemical,thermodynamics,chemistry, physical
The Determination Of The Isosteric Heat Of Hydrogen Adsorption On Carbon Adsorbents From The Nonlocal Density Functioanal Theory Approach

Qr Zheng,Az Gu,Ws Lin,Xs Lu

2002-01-01

Abstract:In this paper, the mean-field approximation theory based nonlocal density,functional theory, Carnahan-Starling equation are applied to determine the bulk gas density and density profile of hydrogen molecules confined within the micropores of carbon nanotubes and the activated carbon. The adsorbed density of hydrogen molecules is determined by the weight average of the local density of adsorbed adsorbate over the whole adsorption space. The maximum adsorption capacities of hydrogen molecules from the geometric estimation, modified Clausius-Clopeyron equation are applied to calculate the isosteric heat of adsorption in the temperature range 77-297K and pressure range 1-13MPa. Comparisons are made between the results from experimental data and DFT calculation.
Effects of structure and surface properties on carbon nanotubes’ hydrogen storage characteristics

Li Xuesong,Zhu Hongwei,Ci Lijie,Xu Cailu,Mao Zongqiang,Wei Bingqing,Liang Ji,Wu Dehai

DOI: https://doi.org/10.1007/BF03183388

2001-01-01

Chinese Science Bulletin

Abstract:Hydrogen adsorption experiments were carried out in special stainless steel vessels at room temperature (298 K) and under 10 MPa using self-synthesized multi-walled carbon nanotubes. In the experiments, carbon nanotubes synthesized by the seeded catalyst method were pretreated by being soaked in chemical reagents or annealed at high temperature before they were used to adsorb hydrogen, but their capacity for hydrogen storage was still poor. Carbon nanotubes synthesized by the floating catalyst method were found to be able to adsorb more hydrogen. They have a hydrogen storage capacity of over 4% after they were annealed at high temperatures, which suggested that they could be used as a promising material for hydrogen storage.
Modeling of low temperature adsorption of hydrogen in carbon nanopores

Justyna Rogacka,Lucyna Firlej,Bogdan Kuchta

DOI: https://doi.org/10.1007/s00894-016-3202-y

IF: 2.172

2017-01-01

Journal of Molecular Modeling

Abstract:We simulated the low temperature (T = 77 K) hydrogen adsorption in carbon slit-shaped nanopores using consecutively united atom (UA) and all atom (AA) representation of hydrogen molecule. We showed that both approximations give comparable estimation of the amount stored, for the wide range of pore width (0.6–2.5 nm). We also showed that at very high pressure (P = 400 bar, corresponding to the fugacity f used in grand canonical Monte Carlo simulations of f = 800 bar) the density of the adsorbed hydrogen structures is larger than the density of bulk liquid at critical temperature (∼76 kg/m3). This result agrees with the experimental observation of the density of the order of 100 kg/m3 for the hydrogen adsorbed in microporous carbons, reported recently in the literature.

chemistry, multidisciplinary,biochemistry & molecular biology,biophysics,computer science, interdisciplinary applications

Adsorption of hydrogen on porous materials of activated carbon and zeolite NaX crossover critical temperature

Cryoadsorption of Hydrogen on Divalent Cation-Exchanged X-zeolites

STUDY ON THE ADSORPTION CHARACTERISTIC OF HYDROGEN ON THE ACTIVATED CARBON AT LOW TEMPERATURES

Micro-channel Development and Hydrogen Adsorption Properties in Templated Microporous Carbons Containing Platinum Nanoparticles

A Linear Comprehensive Adsorption Model of Hydrogen on Super Activated Carbon under Supercritical Conditions

Enhanced CO2 Adsorption Performance on Hierarchical Porous ZSM-5 Zeolite

Adsorption separation of carbon dioxide, methane, and nitrogen on Hβ and Na-exchanged β-zeolite

Experimental Study and Computer Simulation of Hydrogen Adsorption on Carbon Nanofibres.

The Adsorption and Catalytic Cracking of C8 Hydrocarbons on HZSM-5 Zeolite

Temperature dependent behavior of hydrogen molecules on carbon nanostructures

The comparison of adsorption characteristics of CO2/H2O and N2/H2O on activated carbon, activated alumina, zeolite 3A and 13X

Characterisation of porous hydrogen storage materials: carbons, zeolites, MOFs and PIMs

The Prediction of the Adsorption of Hydrogen within the Slit-pores of Carbon Micro-pore Adsorbents

Adsorption equilibrium isotherms and thermodynamic analysis of CH4, CO2, CO, N2 and H2 on NaY Zeolite

Adsorption of CO 2 and N 2 on Synthesized NaY Zeolite at High Temperatures

On the Nature of Spillover Hydrogen Species on Platinum/nitrogen-Doped Mesoporous Carbon Composites: A Temperature-Programmed Nitrobenzene Desorption Study

Adsorption and diffusion of n-heptane and toluene over mesostructured ZSM-5 zeolitic materials with acidic sites

The Determination Of The Isosteric Heat Of Hydrogen Adsorption On Carbon Adsorbents From The Nonlocal Density Functioanal Theory Approach

Effects of structure and surface properties on carbon nanotubes’ hydrogen storage characteristics

Modeling of low temperature adsorption of hydrogen in carbon nanopores