Abstract:[Background] Positron emission tomography/computed tomography (PET/CT) is a routine diagnostic method of particular importance for treatment evaluation and management in oncology. It is very important for PET/CT diagnosis to produce good quality and quantity positron nuclides using medical cyclotron. [Purpose] The effect of irradiation conditions and bombardment parameters on positron nuclide 18F production was analyzed to acquire the optimized production conditions and optimum bombardment parameters. [Methods] Origin 9.0 software was used to analyze the change of 18F yield with different proton beam current and bombardment time. Monte Carlo method was applied to establish the target chamber model of proton irradiation, and the proton energy, thicknesses of Havar foils and the 18O water were analyzed to obtain the optimum conditions of beam current, bombardment time and the proton energy,etc.[Results]Proton beam should thoroughly irradiate on target chamber center to make the best of beam current for triggering as much as nuclear reaction. When 20-MeV proton beam was used to produce 18F, the thicknesses of Havar foil and the target water were recommended to be 60 μm and 3 mm, respectively. Usually, the yield of 18F increases with the beam current. The longer the bombardment time was, the higher the yield of 18F. But with bombardment time increased, the trend of yield became slower. The bombardment time was suggested approximately 60 min. [Conclusion] It is necessary to select the appropriate thicknesses of Havar foil and the 18O water for positron radionuclide 18F production (this paper shows that the thicknesses of Havar foil and the 18O water should be 60 μm and 3 mm when the proton energy is 20 MeV). The irradiation time was suggested approximate 60 min to obtain high yield of 18F. Furthermore, irradiation should be started after the cyclotron run for a period of time for stabilization.

THE STUDY OF REDUCING THE SYNTHESIS COST OF 18 F- FDG BY GE TRACERLAB FX- FN SYNTHESIZER

Radiochemicai Yield of 18F-FDG on a CYRIS HM-12 Cyclotron with an F100 Synthetic System

Synthesis and Analysis of Two Versions of Radioisotope Carbon-14 Labelled Dufulin

Stability and the Improved Methods of 18F-FDG

Design and Application of a Batch-Reactor Microfluidic Device for Synthesis of 18F PET Tracers

Automated synthesis of 18F-fluoroacetate by using Explora FDG4 module

Methodological Progress of 18 F-labeled Aromatic PET Radiotracers

Quality control of18F-fluoroestradiol for positron emission tomography

Long-term quality assurance of [(18)F]-fluorodeoxyglucose (FDG) manufacturing

Microfluidics for synthesis of peptide-based PET tracers.

Overcoming the obstacle of excess acetonitrile content in the final fluorine-18 radiotracers

Difluorocarbene-enabled synthesis of 18 F-radiotracers in positron emission tomography

New Methods and Techniques for F-18-Labeled Radiopharmaceuticals

Labeling and Imaging Study of Fatty Acid Analogue ~(18)F-FHTA on Domestic Synthesis Module

[18F]fluoride Activation and 18F-Labelling in Hydrous Conditions-Towards a Microfluidic Synthesis of PET Radiopharmaceuticals

Comparison study of two18F labeling methods of peptides

Synthesis and quality analysis of sodium 18 F-fluoroacetate and its precursor

Optimization and automation of the radiosynthesis of [18F]Lu-LuFL as a clinically useful PET ligand targeting FAP for tumor imaging

Towards a General Method for Using Cyclotron-Produced Ga68 to Manufacture Clinical and Research Ga68 Tracers

Radiosynthesis challenges of 11C and 18F-labeled radiotracers in the FX2C/N tracerlab and their validation through PET-MR imaging

Analysis and optimization of production conditions for 18F production using a medical cyclotron