Abstract:A stainless steel wire was immersed in a hydrophobic ionic liquid (IL, i.e. 1-octyl-3-methylimidazolium hexafluorophosphate), then was heated under an infrared lighter to make the viscous IL form an even and reproducible film on the steel wire. After that polyaniline (PANI) was electrodeposited on it from an aqueous solution containing 0.1 mol.L-1 aniline and 1.0 mol.L-1 HNO3 through cyclic voltammetry. The potential range was -0.2 similar to 1.2 V (vs. saturated calomel electrode, SCE), the scan rate was 50 mV.s(-1) and the cyclic potential scan was repeated for 70 times. For the electrodeposition a conventional three-electrode system was adopted, including the IL; coated stainless steel wire as working electrode, a platinum wire as counter electrode and a saturated calomel electrode as reference electrode. The resulting PANI-IL composite coating was rinsed with methanol and distilled water. Following this, it was conditioned in a electric furnace with nitrogen atmosphere at 90 degrees C for 30 min, at 250 degrees C for 150 min. When the obtained fiber was cool, it was fixed on a home-made device for solid-phase microextraction (SPME) with epoxy resin. The coating showed netlike structure, with smaller hole and larger surface area than that of PANT. Taking several phenolic derivatives (i.e. 2-chlorophenol, 2-methylphenol, 2,6-dimethylphenol, 2,4-dimethylphenol and 3-methylphenol) as models, the analytical performance of the fiber was investigated. Under the optimized conditions (i.e. extraction temperature: 60 degrees C; extraction time: 40 min; stirring rate: 600 r/min; NaCl concentration: 0.35 g.mL(-1); desorption time: 3 min; desorption temperature: 250 degrees C), when the phenols were determined by GC after headspace solid-phase microextraction with the fiber, the linear ranges were 0.048 similar to 400 mu g.L-1 with correlation coefficients above 0.99; the detection limits were 61 similar to 98 ng.L-1 (S/N=3). The relative standard deviations (RSD) of chromatographic peak area were smaller than 5.5% for five successive measurements with single fiber, and the fiber to fiber RSD was 3.7%similar to 12% for different phenols (n=3). The fiber also presented good stability and its extraction efficiency kept almost unchanged after being used for about 150 times; when the temperature was up to 300 degrees C it did not decompose. In comparison with PANT fiber, the PANI-IL fiber showed higher extraction capability. The PANT-IL fiber was successfully applied to the determination of phenols in waste water from a chemical factory.

Preparation and Applications of Perfluorinated Ion Doped Polyaniline Based Solid-Phase Microextraction Fiber.

Determination of 16 Polycyclic Aromatic Hydrocarbons in Water Using Fluorinated Polyaniline-Based Solid-Phase Microextraction Coupled with Gas Chromatography

A Novel Fluorinated Polyaniline-Based Solid-Phase Microextraction Coupled with Gas Chromatography for Quantitative Determination of Polychlorinated Biphenyls in Water Samples.

Analysis of Perfluorooctane Sulfonate and Perfluorooctanoic Acid with a Mixed-Mode Coating-Based Solid-Phase Microextraction Fiber.

Electrochemical Preparation of Polyaniline-Ionic Liquid Based Solid Phase Microextraction Fiber and Its Application in the Determination of Benzene Derivatives

Solid-phase Microextraction Based on Polyaniline Doped with Perfluorooctanesulfonic Acid Coupled to HPLC for the Quantitative Determination of Chlorophenols in Water Samples.

Electrodeposited Polyaniline As A Fiber Coating for Solid-Phase Microextraction of Organochlorine Pesticides from Water

Sheathed In-Situ Room-Temperature Growth Covalent Organic Framework Solid-Phase Microextraction Fiber for Detecting Ultratrace Polybrominated Diphenyl Ethers from Environmental Samples

Headspace solid-phase microextraction with self-prepared polyaniline coating for rapid determination of trace polybrominated diphenyl ethers (PBDEs) in water and milk

Electrodeposition of Porous Polyaniline Coating on an Etching Stainless Steel Wire As A Fiber for Solid-Phase Microextraction of Triclosan and Chlorophenols in Water Samples

A solid-phase microextraction fiber with carbon nanoparticles as sorbent material prepared by a simple flame-based preparation process

Electrospun UiO-66-F4/polyacrylonitrile nanofibers for efficient extraction of perfluoroalkyl and polyfluoroalkyl substances in environmental media

Fabrication of Polyaniline/silver Composite Coating As a Dual-Functional Platform for Microextraction and Matrix-Free Laser Desorption/ionization.

A Strategy to Enhance the Antifouling Property of Coating for Direct Immersion Solid Phase Microextraction.

Electrochemical Fabrication of Hydrophobic Ionic Liquid–Polyaniline Composite Coating for Solid-Phase Microextraction and Its Application in the GC Determination of Phenolic Compounds

Development of a Highly Robust Solid Phase Microextraction Fiber Based on Crosslinked Methyl Methacrylate–polyhedral Oligomeric Silsesquioxane Hybrid Polymeric Coating

Polyaniline-coated kapok fibers for convenient in-syringe solid-phase microextraction and determination of organochlorine and pyrethroid pesticide residues in aqueous samples

Polythiophene As a Novel Fiber Coating for Solid-Phase Microextraction

Fabrication of a Polymeric Composite Incorporating Metal-Organic Framework Nanosheets for Solid-Phase Microextraction of Polycyclic Aromatic Hydrocarbons from Water Samples.

Exploration of metal-organic framework MOF-177 coated fibers for headspace solid-phase microextraction of polychlorinated biphenyls and polycyclic aromatic hydrocarbons

Coupling Solid-Phase Microextraction with Ambient Mass Spectrometry Using Surface Coated Wooden-Tip Probe for Rapid Analysis of Ultra Trace Perfluorinated Compounds in Complex Samples