Abstract:Objective: To analyze the wear debris characteristics ofcarbon-based nano- multilayer coatings on Ti(6)Al(4)V alloys and compared with the cobalt chromium molybdenum alloy (CoCrMo) femoral head to evaluate the friction and wear performance of the new coated femoral head. Methods: Three groups were set up in the wear simulation experiment according to the type of femoral head. Group A: imported Cobalt-Chromium-Molybdenum alloy femoral head (CoCrMo); group B: Titanium alloy femoral head (Ti(6)Al(4)V) with carbon-based nano-multilayer coatings; group C: domestic Cobalt-Chromium-Molybdenum alloy femoral head (CoCrMo). All heads were jointed with an ultra-high molecular weight polyethylene (UHMWPE) acetabular cup. Serum samples were collected and stored in the hip joint simulator. After the sample has been digested and diluted, it was filtered through 5 μm, 1.2 μm and 0.4 μm filters, and the filter paper was collected for testing. Scanning electron microscope (SEM) was used to randomly select regions on the filter to obtain images of wear debris. Energy dispersive X-ray spectroscopy (EDS) was used to determine the elemental type of the particle and to eliminate possible contamination. The composition and structure of the abrasive chips were measured using Fourier transform infrared spectrometer (FTIR). The parameters related to the wear debris includingparticle size, shape, number and volume were calculated. The differences in correlation parameters between the groups were compared to evaluate the friction and wear properties of the new coated joints. Results: The main component of the wear debris produced was UHMWPE, and the particle size was mostly below 1 μm. The submicron particle ratio of group B was 49.4%, which was significantly lower than that of the group A and C (75% and 60%, respectively; χ(2)=66.032, 31.754, both P<0.017). The shape was mainly round, and there was no statistical difference between the groups (χ(2)=0.590, P=0.744). The number of particles in group B was significantly less than that of group C on all filters (t=9.960, 8.019, 5.790, all P<0.01), and less than group A on the 0.4 μm filter (t=7.810, P=0.000). Conclusion: The frictional wear performance of the new carbon-based nano-multilayer coatings femoral head is significantly better than that of the domestic femoral head, and even partially exceeds the imported femoral head level, which helps to reduce the production of particles and prevent osteolysis and aseptic loosening induced by UHMWPE particles.

In vitro testing of Al2O3–Nb composite for femoral head applications in total hip arthroplasty

Zirconium niobium alloy femoral head in young and middle-aged recent treatment of total hip replacement

Pure Alumina Bearings with Cementless Stems Versus Sandwich Bearings with Cemented Stems in Total Hip Arthroplasty.

Preparation and Microstructural Characterization of Al<sub>2</sub>O<sub>3</sub>/ZrO<sub>2</sub> Nanocomposites to Use in the Femoral Head of Hip Replacement

Preparation and Microstructural Characterization of Al2O3/ZrO2 Nanocomposites to Use in the Femoral Head of Hip Replacement

Fabrication of dense α-alumina layer on Ti-6Al-4V alloy hybrid for bearing surfaces of artificial hip joint

Reliability assessment in advanced nanocomposite materials for orthopaedic applications

Intermediate outcomes of alumina-on-alumina bearing total hip arthroplastyTotal arthroplasty, replacement, hip; Ceramic; Frictione; Prostheses and implants

Silicon Nitride Bearings for Total Joint Arthroplasty

[Intermediate Outcomes of Alumina-on-alumina Bearing Total Hip Arthroplasty].

LONG TERM DATA CONCERNING THE USE OF ALL ALUMINA IN TOTAL HIP REPLACEMENTS: SPECIAL INTEREST IN YOUNG AGE POPULATION.

Nano-scale topography of bearing surface in advanced alumina/zirconia hip joint before and after severe exposure in water vapor environment.

Surface Topology of Advanced Alumina/Zirconia Composite Femoral Head As Compared with Commercial Femoral Heads Made of Monolithic Zirconia

The aging micromechanisms of alumina matrix composite (AMC) used in total hip arthroplasty

Wear Degradation of Long-Term in Vivo Exposed Alumina-on-alumina Hip Joints: Linking Nanometer-Scale Phenomena to Macroscopic Joint Design.

Wear Simulation of Ceramic-on-Crosslinked Polyethylene Hip Prostheses: A New Non-Oxide Silicon Nitride versus the Gold Standard Composite Oxide Ceramic Femoral Heads.

Computational biomechanical study on hybrid implant materials for the femoral component of total knee replacements

Comparison of Wear Properties of Alumina-Alumina Articulating Surfaces with Conventional Material Couples Used for Total Hip Arthroplasty

[Five Million Wear Simulation and Particle Analysis of Carbon-Based Nano-Multilayer Coatings Titanium Alloy Femoral Head].

Thirty years of experience with alumina-on-alumina bearings in total hip arthroplasty

Mechanical Behaviour of Umbrella-Shaped, Ni-Ti Memory Alloy Femoral Head Support Device during Implant Operation: A Finite Element Analysis Study