Abstract:In this paper, the effects of the width of the mold on the surface velocity, flow field pattern, turbulent kinetic energy distribution, and surface-level fluctuation in the mold were studied with measurement of the flow velocity near the surface of the mold at high temperature with the rod deflection method and numerical calculation with the standard k-ε model coupled with the discrete-phase model (DPM) model for automobile exposed panel production. Under the conditions of low fixed steel throughput of 2.2 ton/min, a nozzle immersion depth of 140 mm, and an argon gas flow rate of 4 L/min, as the width of the mold increases from 880 mm to 1050 mm and 1300 mm, the flow velocity near the surface of the mold decreases. The flow direction changes from the positive velocity with the mold widths of 880 mm and 1050 mm to the unstable velocity with the mold width of 1300 mm. The calculated results are in good agreement with the measured results. The turbulent kinetic energy near the submerged entry nozzle (SEN) gradually increases, and the risk of slag entrainment increases. Under the conditions of high fixed steel throughput of 3.5 ton/min, the SEN immersion depth of 160 mm, and the argon gas flow rate of 10 L/min, as the width of the mold increases from 1600 mm to 1800 mm and 2000 mm, the velocity near the mold surface decreases. The flow velocity at 1/4 of the surface of the mold is positive with the mold width of 1600 mm, while the velocities are negative with the widths of 1800 mm and 2000 mm. The calculated results are basically consistent with the measured results. The high turbulent kinetic energy area near the nozzle expands to a narrow wall, and the risk of slag entrainment is significantly increased. In both cases of low and high fixed steel throughput, the change rules of the flow field in the mold with the width are basically the same. The argon gas flow rate and the immersion depth of SEN should be adjusted reasonably to optimize the flow field in the mold with different widths under the same fixed steel throughput in the practical production.

Analysis of Heat-transfer and Structure of Air Slip Mold

Simulation Analysis of Thermal Stress During Casting Process of Large-Sized Alloy Steel Ingot

Thickness Distributions of Mold Flux Film and Air Gap in Billet Ultra-High Speed Continuous Casting Mold Through Multiphysics Modeling

Thermomechanical Model of Heat Transffer in Bloom Casting Mold

Investigation on Heat Transfer in Molds with Different Water-Cooling Structures Under Billet High-Speed Continuous Casting

Analysis of Thermomechanical Behavior in Continuous Bloom Casting Mold

Analysis of heat transfer and thermal stress in continuous casting with mechanical reduction

Effect of Mold Width on the Flow Field in a Slab Continuous-Casting Mold with High-Temperature Velocity Measurement and Numerical Simulation

The Effect of Mold Structure and Cooling Parameters on Heat Transfer during Billet High-Speed Continuous Casting

Review of Testing Methods on the Heat Transfer Characteristics of Mold Slag Film

Method for Determining the Boundary Condition of Heat Transfer in Mold for Slab Casting

Influence of Mold and Heat Transfer Fluid Materials on the Temperature Distribution of Large Framed Molds in Autoclave Process

Numerical Simulation on Thermo-Mechanical Coupling in Bloom Mold by Finite Element Method

Finite element numerical simulation on Thermo Mechanical couple in bloom mold

Heat transfer behavior in ultrahigh-speed continuous casting mold

Numerical Study on Characteristic Positions and Transition of Flow Patterns in a Slab Continuous Casting Mold

Analysis of Longitudinal Cracking and Mold Flux Optimization in High-Speed Continuous Casting of Hyper-Peritectic Steel Thin Slabs

Simulation of the Flow-Heat Transfer Process in Billet Mold and Analysis of the Billet Rhomboidity Phenomenon

In-depth study of mold heat transfer for the high speed continuous casting process

Heat transfer behaviour of funnel mould copper plates during thin slab continuous casting and channel structure optimization

A coupled model on fluid flow, heat transfer and solidification in continuous casting mold