Abstract:While personal aerosol samplers have been characterized primarily based on wind tunnel tests conducted at relatively high wind speeds, modern indoor occupational environments are usually represented by very slow moving air. Recent surveys suggest that elevated levels of occupational exposure to inhalable airborne particles are typically observed when the worker, operating in the vicinity of the dust source, faces the source. Thus, the first objective of this study was to design and test a new, low cost experimental protocol for measuring the sampling efficiency of personal inhalable aerosol samplers in the vicinity of the aerosol source when the samplers operate in very slowly moving air. In this system, an aerosol generator, which is located in the centre of a room-sized non-ventilated chamber, continuously rotates and omnidirectionally disperses test particles of a specific size. The test and reference samplers are equally distributed around the source at the same distance from the centre and operate in parallel (in most of our experiments, the total number of simultaneously operating samplers was 15). Radial aerosol transport is driven by turbulent diffusion and some natural convection. For each specific particle size and the sampler, the aerosol mass concentration is measured by weighing the collection filter. The second objective was to utilize the new protocol to evaluate three widely used aerosol samplers: the IOM Personal Inhalable Sampler, the Button Personal Inhalable Aerosol Sampler and the 25 mm Millipore filter holder (closed-face C25 cassette). The sampling efficiencies of each instrument were measured with six particle fractions, ranging from 6.9 to 76.9 micro m in their mass median aerodynamic diameter. The Button Sampler efficiency data demonstrated a good agreement with the standard inhalable convention and especially with the low air movement inhalabilty curve. The 25 mm filter holder was found to considerably under-sample the particles larger than 10 micro m; its efficiency did not exceed 7% for particles of 40-100 micro m. The IOM Sampler facing the source was found to over-sample compared with the data obtained previously with a slowly rotating, freely suspended sampler in a low air movement environment. It was also found that the particle wall deposition in the IOM metallic cartridge was rather significant and particle size-dependent. For each sampler (IOM, Button and C25) the precision was characterized through the relative standard deviation (RSD) of the aerosol concentration obtained with identical samplers in a specific experiment. The average RSD was 14% for the IOM Sampler, 11% for the Button Sampler and 35% for the 25 mm filter cassette. A separate set of experiments, performed with the Simplified Torso showed that in very slowly moving air a personal sampler can be adequately evaluated even when it is not attached to a body but freely suspended (confirming the data reported previously).

Field Comparison of Impingers and Treated Filters for Sampling of Total Aliphatic Isocyanates with the MAP Reagent

Performance of personal inhalable aerosol samplers in very slowly moving air when facing the aerosol source

Analysis of Portable Impactor Performance for Enumeration of Viable Bioaerosols

A comparison of total inward leakage measured using sodium chloride (NaCl) and corn oil aerosol methods for air-purifying respirators

Comparison among filter-based, impactor-based and continuous techniques for measuring atmospheric fine sulfate and nitrate

Applicability of a Modified MCE Filter Method with Button Inhalable Sampler for Monitoring Personal Bioaerosol Inhalation Exposure

Comparison of Sampling Techniques for the Analysis of Particulate Metal Impurities in Gases

Comparison of Improve and Niosh Carbon Measurements

Performance of High Flow Rate Samplers for Respirable Particle Collection

Comparison of methods for personal sampling of inhalable and total lead and cadmium-containing aerosols in a primary lead smelter

Application of a needle trap device packed with a MIP@MOF nano-composite for efficient sampling and determination of airborne diazinon pesticide

The effect of sampling inlets on the PM-10 and PM-15 to TSP concentration ratios

Quantification of nitrated-polycyclic aromatic hydrocarbons in atmospheric aerosol samples with in-injection port thermal desorption-gas chromatography/ negative chemical ionization mass spectrometry method

Particle and gas phase sampling of PCDD/Fs and dl-PCBs by activated carbon fiber and GC/MS analysis

Calibration comparison between two passive samplers -o-DGT and POCIS- for 109 hydrophilic emerging and priority organic compounds

Evaluation of Aeris mid-infrared absorption (MIRA), Picarro CRDS (cavity ring-down spectroscopy) G2307, and dinitrophenylhydrazine (DNPH)-based sampling for long-term formaldehyde monitoring efforts

Sampling and recovery of ignitable liquid residues (ILRs) from fire debris using capillary microextraction of volatiles (CMV) for on-site analysis

Efficiencies of filtration sampling and extraction for recovery of viable Staphylococcus aureus bioaerosols

In vitro toxicity evaluation in A549 cells of diesel particulate matter from two different particle sampling systems and several resuspension media

Investigation of Cut-Off Sizes and Collection Efficiencies of Portable Microbial Samplers

Field demonstration for the solvent-based sampling method to perform compound-specific isotope analysis on gas-phase VOC