Abstract:Macrosegregation is a very common problem for the quality control of all cast ingots. The effect of current on the structure and macrosegregation in dual alloy ingot processed by electroslag remelting (ESR) was investigated experimentally with various analytical methods. In this study, the electrode consisted of NiCrMoV alloy bar (upper part) and CrMoV alloy (lower part) with a diameter of 55 mm, was remelted in a laboratory-scale ESR furnace with the slag containing 30 mass pct alumina and 70 mass pct calcium fluoride under an open air atmosphere. The results show that the macrostructures of three ingots processed by electroslagremelting with different currents are nearly similar. The thin equiaxed grains region and the columnar grains region are formed under the ingot surface, the latter region is the dominant part of the ingot. The typical columnar structure shows no discontinuity among the NiCrMoV alloy zone, the CrMoV alloy zone, and the transition zone in three ingots. With the increase of the current, the grain growth angle increases due to the deeper molten metal pool. The secondary dendrite arm spacing (SDAS) firstly decreases, then increases. The SDAS is dominated by the combined effect of the local solidification rate and the width of mushy region. With the current increasing from 1500 A to 1800 A and 2100 A, the width of the transition zone decreases from 147 mm to 115 mm and 102 mm. The macrosegregation becomes more severe due to the fiercer flows forced by the Lorentz force and the thermal buoyancy force. The cooling rate firstly increases, then decreases, due to the effect of the flows between the mushy region and metal pool and the temperature gradient at the mushy zone of the solidification front. With a current of 1800 A, the SDAS is the smallest and cooling rate is the fastest, indicating that less dendrite segregation and finer precipitates exist in the ingot. Under the comprehensive consideration, the dual alloy ingot processed by the ESR with a current of 1800 A is the best because it has the smallest SDAS, the appropriate grain growth angle, moderate macrosegregation and thickness of the transition zone.

Macrosegregation Behavior of Ti-10V-2Fe-3Al Alloy During Vacuum Consumable Arc Remelting Process

Melt convection and macrosegregation in the vacuum arc remelted Ti2AlNb ingot: Numerical methods and experimental verification

Modeling of Macrosegregation Formation and the Effect of Enhanced Cooling During Vacuum Arc Remelting Solidification of NbTi Alloy Ingot

Zr and Mo macrosegregation in Ti6246 titanium alloy industrial-scale ingot by vacuum arc remelting

Effect Of Current On Structure And Macrosegregation In Dual Alloy Ingot Processed By Electroslag Remelting

Quantitative Characterization of Beta Fleck Segregation in a Ti-17 Alloy Ingot Produced by Vacuum Arc Remelting Without Electromagnetic Stirring

Numerical simulation and experimental study of vacuum arc remelting (VAR) process for large-size GH4742 superalloy

Numerical simulation of macrosegregation phenomenon in Cu-6wt%Ag alloy ingots fabricated by electromagnetic stirring

On the Prediction of Macrosegregation in Vacuum Arc Remelted Ingots

Effect of Electromagnetic Stirring on Fine Grain Formation and Tensile Property Improvement for Fe-Ni Superalloy

Predicting the Three-dimensional Grain Structure of Superalloys during Vacuum Arc Remelting Process

The influence of melting process and parameters on the structure and homogeneity of titanium-tantalum alloys

Numerical simulation of macrosegregation heredity on TC4 titanium alloy ingot by vacuum arc remelting

Experimental and Numerical Study of Macrosegregation in a 160 Steel Ingot

The Structural Evolution And Segregation In A Dual Alloy Ingot Processed By Electroslag Remelting

CFD Investigation of Melting Behaviors of Two Alloy Particles During Multiphase Vacuum Refining Process

Segregation behavior and precipitated phases of super-austenitic stainless steel influenced by electromagnetic stirring

Motion Behavior of Ce‐Containing Inclusions in 8Cr4Mo4V‐Bearing Steel during Vacuum Arc Remelting

Numerical Investigation of Grain Structure Under the Rotating Arc Based on Cellular Automata-Finite Element Method During Vacuum Arc Remelting Process

Segregation in Fusion Weld of 2219 Aluminum Alloy and Its Influence on Mechanical Properties of Weld

Numerical simulation of macro-segregation in steel ingot during solidification