Abstract:A multiphase mathematical model was established to study the fluid flow, the open-eye formation, and the residence time of slag inclusions in a bottom argon-blowing ladle. The fluid flow was solved using the Eulerian-Lagrangian multiphase approach, and the interface between different phases was described using the Volume of Fluid (VOF) model. The motion of argon bubbles and slag inclusions was tracked with the method of the discrete phase model (DPM). Moreover, the composition transformation of slag inclusions was predicted by employing a kinetic model based on the coupled reactions model. Numerical results show that the flow of the molten steel and the open-eye of the molten slag were sensitive to the argon blowing rate. The larger argon blowing rate expanded the volume of the plume and the area of the open-eye. Slag droplets were considered to move with the steel to the region away from the open-eye and then entrained into the steel to form slag inclusions as there was barely any downward velocity around the open-eye. Most slag inclusions were able to be removed immediately after the entrainment, while there still were some slag inclusions retaining in the steel for as long as thousands of seconds. The composition of slag inclusions had an apparent transformation due to reactions with the steel. The content of SiO 2 and MgO in slag inclusions had a decrease while that of Al 2O 3 rose remarkably. The variation of SiO 2 content occurred in the early one minute and the MgO content reduced gradually from 7.34wt% to 1.12wt% in 10 min. The composition transformation of slag inclusions was basically completed within 10 min in the current case.

CFD Investigation of Melting Behaviors of Two Alloy Particles During Multiphase Vacuum Refining Process

Phase Field Simulation for Non-Isothermal Solidification of Multicomponent Alloys Coupled with Thermodynamics Database

Multi-component Phase-Field Simulation of Microstructural Evolution and Elemental Distribution in Fe–Cu–Mn–Ni–Al Alloy

CFD-DEM-VOF-phase diagram modelling of multi-phase flow with phase changes

Dynamic solidification model of low-density FeCrNiAl multi-component alloy

Factors Affecting the Mixing Characteristics of Molten Steel in the RH Refining Process

Research of mixing characteristics of molten steel in RH refining

Temperature Field Calculation on Cold Crucible Continuous Melting and Directional Solidifying Ti50Al Alloys

Melt convection and macrosegregation in the vacuum arc remelted Ti2AlNb ingot: Numerical methods and experimental verification

Numerical Simulation and Experimental Investigation on Inclusion-Argon-Liquid Steel Phenomenon in RH Refining of High-Manganese and High-Aluminum Steel

Numerical Analysis of Particulate Migration Behavior Within Molten Pool During TIG-Assisted Droplet Deposition Manufacturing of SiC Particle-Reinforced Aluminum Matrix Composites.

Multiphase modelling of the transient flow for Sn-15Pb and 357.0 alloys in semi-solid die casting process

Modeling of Dynamic Recrystallization Volume Fraction Evolution for AlCu4SiMg Alloy and Its Application in FEM

Numerical Simulation for the Transport Phenomena in Melting Processes of Blade-Like Castings Using a Continuum Model

Three-Dimensional Simulation of Macrosegregation in a 36-Ton Steel Ingot Using a Multicomponent Multiphase Model

Numerical Calculation of Flow Field Inside TiAl Melt During Rectangular Cold Crucible Directional Solidification

INFILTRATION OF MOLTEN ALUMINUM WITH TRANSIENT SOLIDIFICATION AND REMELTING IN CENTRIFUGAL CASTING PROCESSES

Fluid flow, slag entrainment, and composition evolution of slag inclusions during vacuum degassing refining

Influence of process parameters on CET in Ti–Al alloy ingot with consideration of shrinkage cavity formation: A computer simulation

Finite Element Analysis and Computational Fluid Dynamics Verification of Molten Pool Characteristics During Selective Laser Melting of Ti-6Al-4V Plates

Temperature field calculation on cold crucible continuous melting and directional solidifying Ti5OAl alloys