Abstract:Si3N4/SiC composites containing 0-30 vol% SiC were fabricated by pressureless sintering and sinter-post-HIPing method using fine Si3N4 and nano-sized SiC powders. Specimens reached full density (>96% theoretical density (th. d.)) except the composites made by pressureless sintering which contained a small amount of sintering additives or a large amount of SiC. All composites with 10 mass% sintering additives reached full density (similar to 99% th. d.) by sinter-post-HIPing. The addition of SiC particles greatly influenced the grain morphology of the Si3N4 matrix. The average grain thickness, length and aspect ratio decreased with increasing SiC content because of grain boundary pinning by SiC particles. Also the mechanical properties were markedly dependent upon the fraction of SiC particle reinforcement, as well as matrix grain size and porosity. When the materials were pressureless sintered, the strength of the composite increased with SiC additions below 20 vol%. Further increase in the SIC content resulted in a corresponding decrease in strength. Maximum strength of 1150 MPa was attained at 20 vol% SiC addition. The increase in strength by addition of SiC is due to decrease of grain size of Si3N4 matrix grain size, and the decrease by further increase in SiC content is caused by porosity and SiC agglomerate. On the other hand, toughness decreased monotonically with SiC content. The strength of all samples was enhanced by sinter-post-HIPing without any change in fracture toughness. The strength of sintered samples with 10-15 vol% SiC increased by similar to 20% to 1260 MPa by post-HIPing. The increase in strength by post-HIPing was interpreted as being due to a decrease flaw size.

The Effect of Si3N4 on Microstructure, Mechanical Properties and Oxidation Resistance of HfB2-based Composite

The effect of sintering aids on microstructure and mechanical properties of HfB2-SiC composites

Fabrication and Evaluation on Thermal Stability of Hafnium Diboride Matrix Composite at Severe Oxidation Condition

The Effect of B4C on the Microstructure and Thermo-Mechanical Properties of HfB2-based Ceramics

Preparation and Thermal Ablation Behavior of HfB2–SiC‐Based Ultra‐High‐Temperature Ceramics under Severe Heat Conditions

Effect of CaF2 on Microstructure and Mechanical Properties of Pressureless Sintered Si3N4/BN Composites

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

Effects of silicon addition on the microstructure and properties of B 4 C–SiC composite prepared with polycarbosilane-coated B 4 C powder

Effect of Hexagonal BN on the Microstructure and Mechanical Properties of Pressureless Sintered Porous Si3N4 Ceramics

Wet oxidation behavior of C/SiC–SiHf(B)CN composites at high temperature

The Effect of Tio2 and Zro2 Additives on the Density, Microstructure, and Mechanical Properties of Pressureless Sintered Sic-B4c

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Effect of AlN as sintering aid on hot-pressed ZrB2–SiC ceramic composite

Strong and Tough HfC-HfB2 Solid-Solution Composites Obtained by Reactive Sintering with a SiB6 Additive

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

HfB2-CNTs Composites with Enhanced Mechanical Properties Prepared by Spark Plasma Sintering

Effect of Al 2 O 3 addition on properties of non-sintered SiC–Si 3 N 4 composite refractory materials

The impact of Si3N4 incorporation on the mechanical characteristics of ZrB2-SiC nanocomposite sintered via pressureless method

Effect of SiC on the anti-ablation resistance and flexural strength of (Hf-Ta-Zr)C-C/C composites

Mechanical Properties and Interfaces of Cf/SiC Composites