Abstract:In order to explore the coupling effects of second shear flow and temperature fields on the formation as well as the evolution of crystal morphologies of high-density polyethylene (HDPE), the crystal morphologies of the parts obtained by multi-fluid multi-injection molding (MFMIM) were investigated. The main feature of MFMIM is that the polymer melts in two different injection units are injected sequentially into the cavity to form an encapsulated sandwich-structure product. Polarizing light microscopy (PLM) results showed that some peculiar microstructures (e. g. cylindritic structures and ring-banded spherulites) were generated in the skin layer of the MEMIM parts. With the aid of scanning electronic microscopy (SEM), a detailed description of cylindritic structure was obtained, which showed that the cylindritic structure consisted of some ring-banded spherulites. For comparison,the crystalline morphology of the sample molded by conventional injection molding (CIM) was also investigated. Different from the MFMIM parts, there were not observed any ring-banded spherulites or cylindritic structures in CIM parts except the common spherulites. And there was not a significant skin-core structure formed due to the higher temperature of the mold. Based on the comparison between the experimental results of the MFMIM parts and those of the CIM counterparts, it was concluded that the main reasons for ring-banded spherulites and cylindritic structures arising in the skin layer of MFMIM parts were the shearing and the complex thermo-mechanical fields provided by the secondary melt penetration process. Therefore, on the basis of the previous results, the mechanisms of ring-banded spherulites and cylindritic structures formation were discussed.

Hierarchical Crystalline Structure of Hdpe Molded by Gas-Assisted Injection Molding

Crystalline Morphology of HDPE Molded by Gas Assisted Injection

Role of Gas Delay Time on the Hierarchical Crystalline Structure and Mechanical Property of Hdpe Molded by Gas-Assisted Injection Molding

Crystallization Behavior and Molecular Orientation of High Density Polyethylene Parts Prepared by Gas‐assisted Injection Molding

Morphology and mechanical property of high-density polyethylene parts prepared by gas-assisted injection molding

Banded Spherulites of Hdpe Molded by Gas-Assisted and Conventional Injection Molding

Role of gas cooling time on crystalline morphology and mechanical property of the HDPE parts prepared by gas-assisted injection molding

THE EFFECT OF GAS-ASSSTED NJECTON MOLDNG ON THE CRYSTALLNE MORPHOLOGY OF HDPE AND TS NUMERCAL SMULATON

Simulation of Gas-Assisted Injection Molding of High-Density Polyethylene: the Role of Rheological Properties and Physical Fields on the Crystalline Morphology

Hierarchical crystalline structures and dynamic mechanical properties of injection-molded bars of HDPE: Attributes of temperature field

A novel hierarchical crystalline structure of injection-molded bars of linear polymer: co-existence of bending and normal shish–kebab structure

Extension of the Orientation Region of High Density Polyethylene Molded by Gas‐assisted Injection Molding: Control of the Thermal Field

Effect of thermal gradient field with phase change on crystal morphologies of HDPE during GAIM process

The hierarchical structure of water-assisted injection molded high density polyethylene: Small angle X-ray scattering study

CRYSTAL MORPHOLOGY OF HDPE MOLDED BY MULTI-FLUID MULTI-INJECTION MOLDING

Cylindritic Structures of High-Density Polyethylene Molded by Multi-Melt Multi-Injection Molding

Tailoring The Crystalline Morphologies And Mechanical Properties Of High- Density Polyethylene Parts By A Change In The Fluid Flow Pattern Under Gas- Assisted Injection Molding

Crystal morphology of water-assisted injection molded high-density polyethylene with two different molecular weights

Multi-Layered Structure of Ipp Molded by Gas-Assisted Injection Molding

The Role of Gas Penetration on Morphological Formation of Polycarbonate/polyethylene Blend Molded by Gas-Assisted Injection Molding

Morphological study of linear low-density polyethylene molded by gas-assisted injection molding