Abstract:Currently, the surface integrity-related issues of additively manufactured parts are limiting the potential high-end applications. The present work investigates the effectiveness of the pulsed-electropolishing technique to improve the surface integrity of aluminium alloys fabricated using the selective laser melting (SLM) technique. Due to its low density, high corrosion resistance, the aluminium alloys considerably enhance the performance of lightweight critical parts for different industrial applications. In this study, selective laser melted AlSi10Mg samples were subjected to microstructural examinations using optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction technique. The microhardness and tensile properties were determined using a microhardness tester and a universal testing machine, respectively. The pulsed-electropolishing process was employed for the surface finishing of the SLM-processed AlSi10Mg samples. The effect of current density on the electropolishing of selective laser melted AlSi10Mg alloy were also investigated. The microstructures of printed samples revealed a density of greater than 99.9% and weld beads along the build direction (longitudinal) and laser scan paths perpendicular to the build direction (transverse). The microhardness, yield and tensile strength properties were similar in both as-printed conditions. The pulsed electropolishing results showed a beneficial effect of higher current density values, resulting in decreased surface roughness of the SLM-processed AlSi10Mg samples. Compared to as-printed conditions, a significant decrease in surface roughness of about ∼73.35% under optimized electropolishing conditions was noted. The material ratio curve shows that the surface topography becomes more uniform with increased current density and has lesser surface undulations for as-printed samples. The 2D line profilogram and 3D surface topography of electropolished SLM-processed samples reveal the surface finish quality characteristics. The material ratio curve aids as an effective method to assess and qualify the surface topography of electropolished samples.

Large-area self-ordered aluminium sub-micrometre dot arrays prepared by electropolishing on polycrystalline aluminium at constant current

Preparation and Annealing-Induced Structural Transition of Self-Organized Nanostripes on the Electropolished Aluminium Surface

Afm Study of Quasi-Ordered Stripe-Like Nanostructures on Surfaces of Aluminum

Electropolishing of single crystal and polycrystalline aluminum to achieve high optical and mechanical surfaces

Highly Tunable Complementary Micro/Submicro-Nanopatterned Surfaces Combining Block Copolymer Self-Assembly and Colloidal Lithography.

Effect of Al Polishing Conditions on the Growth and Morphology of Porous Anodic Alumina Films

Investigation on pulsed electrolytically polished AlSi10Mg alloy processed via selective laser melting technique

Generation of surface texture on 2A50 aluminum alloy with electrochemical micromachining for tribological application

Characterizing and optimizing the electropolishing and pore arrangement in porous anodic aluminum oxide (AAO)

Growth of Highly-Ordered Metal Nanoparticle Arrays in the Dimpled Pores of an Anodic Aluminum Oxide Template

Micrometer And Nanometer Scale Photopatterning Of Self-Assembled Monolayers Of Phosphonic Acids On Aluminum Oxide

Structure-Performance Relationships of Complexing Agents on the Chemical Mechanical Polishing of 6063 Aluminum Alloy

Optimization of electrolytic plasma polishing process and surface performance analysis for 6061 aluminum alloy

Preparation and Study of Ordered Porous Anodic Alumina Film

Research on the Chemical Mechanical Polishing Process of Aluminum Alloy Wafers with Acidic Slurry

Electrochemical Polishing of 7075 Al Alloy in Phosphoric Acid

Fabrication of Anodic Aluminum Oxide Templates with Small Interpore Distances

Improving the Solidification Structure of Commercially Pure Aluminium with Electropulse Acting on Liquid Metal

Comparison of Electropolishing of Aluminum in a Deep Eutectic Medium and Acidic Electrolyte

Characterization of nanopores arrangement of anodic alumina layers synthesized on low-(AA1050) and high-purity aluminum by two-step anodizing in sulfuric acid with addition of ethylene glycol at low temperature

Investigation of the microhole arrays generated by masked jet electrochemical machining with polyaluminum chloride electrolyte