Decimation Filter Design for DDC and Implementing It with FPGA

ZHANG Bin,HE Zi-shu

DOI: https://doi.org/10.3969/j.issn.1672-9528.2006.01.032

2006-01-01

Abstract:This paper describes the system design of decimation filter and the implementing method. Through the cascade of CIC filter, HB filter and FIR filters, the data frequency is cut down. The method is validated by the test results.

What problem does this paper attempt to address?

Decimation Filter Design in Sigma-delta ADC

CAI You,HAN Yan

DOI: https://doi.org/10.3969/j.issn.1001-9146.2006.05.019

2006-01-01

Abstract:Decimation is an important component of oversampled analog-to-digital conversion(ADC).It transforms the digitally modulated signal from short words occurring at high sampling rate to longer words at Nyquist rate.This paper presents an efficient design and implementation of a digital decimation filter for various downsampling ratios,which can be applicable for sigma-delta modulator orders from 1 to 7,and input word length from 1 to 32 bits.The proposed decimation filter consists of Cascaded-Integrated-Comb(CIC) filter,compensation lowpass filter and narrow transition-band finite impulse response(FIR) filter using canonic signed digit(CSD) number system.Multi-stage multi-rate signal processing is used to implement compensation lowpass and half-band filters.As a design example, a decimation filter with a downsampling ratio of 256,which is applicable for third-order cascaded sigma-delta modulators is presented.
The Design and FPGA Verification of a General Structure, Area-optimized Interpolation Filter Used in /spl Delta/-/spl Sigma/ DAC

Xiaowei Huang,Yan Han,Lei Chen

DOI: https://doi.org/10.1109/icsict.2006.306632

2006-01-01

Abstract:This paper describes a general structure, area-optimized interpolation filter used in the Delta-Sigma digital-to-analog converter (DAC) intended for the portable digital audio system. The whole filter system simulation, verilog implement and FPGA verification are processing, the signal-to-noise(S/N) achieves 115 dB and the total area is small enough which has good prospect for the audio applications
An Enhancement of Decimation Process using Fast Cascaded Integrator Comb (CIC) Filter

Rozita Teymourzadeh,Masuri Othman

DOI: https://doi.org/10.48550/arXiv.1806.00704

2018-06-03

Abstract:The oversampling technique has been shown to increase the SNR and is used in many high-performance systems such as in the ADC for audio and DAT systems. This paper presents the design of the decimation and it's VLSI implementation which is the sub-component in the oversampling technique. The design of three main units in the decimation stage that is the Cascaded Integrator Comb (CIC) filter, the associated half-band filters and the droop correction are also described. The Verilog HDL code in Xilinx ISE environment has been derived to describe the CIC filter properties and downloaded into Virtex II FPGA board. In the design of these units, we focus on the trade-off between the speed improvement and the power consumption as well as the silicon area for the chip implementation.

Signal Processing
Design and Implementation of a Modified High Performance and Low Power CIC Interpolation Filter

Xiaopeng Liu,Yan Han,Guo Liang,Mingyu Wang,Lu Liao

DOI: https://doi.org/10.1109/edssc.2011.6117685

2011-01-01

Abstract:This paper presents a modified cascaded integral comb (CIC) interpolation filter in order to improve filter characteristics and reduce power consumption at the same time. The modified CIC interpolation filter is a two-stage multiplier-less CIC-based interpolator. The first stage is a cascaded CIC filter whereas the second stage is a cascaded CIC filter and a second-order compensator. In an effort to reduce power consumption, the poly-phase decomposition and no-recursive algorithm is used when the modified filter is implemented. Simulation and synthesis results indicate that the stop-band attenuation is up to 137.7 dB and the pass-band drop is only 0.0003 dB with the filter interpolation factor 16. Working at 50 MHz clock frequency, the filter can reduce the power consumption of 16.78%. This new interpolator is implemented on Altera Cyclone III EP3C10E144C8 FPGA.
Design of a HDTV Audio Decoder on a Fixed Point DSP Chip

ZHANG Jin,XU Yuan-xin,ZHANG Ji,WANG Kuang

DOI: https://doi.org/10.3969/j.issn.1671-7147.2005.03.003

2005-01-01

Abstract:The paper describes a DVB based HDTV audio decoder used in multi-channel extension and presents an improved algorithm for the synthesis filter bank. It is found that when the symmetry of coefficient and the similarity of the allocation tables, computational amount and memory size are reduced by more than 50%. DSP/BIOS operating system simplifies developing various DSP systems. This decoder can also be used in Digital Audio Broadcasting systems.
Implemented Architecture Design of Deblocking Filter for H.264

FANG Jian,ZHANG Ding,XU Hong,WANG Kuang

DOI: https://doi.org/10.3785/j.issn.1008-973x.2008.03.019

2008-01-01

Abstract:An implemented architecture of deblocking filter was proposed to improve the performance of deblocking filter in H.264.With a novel filtering order, only 252 cycles were needed to perform the deblocking filter of a macroblock,consequently the unfiltered data storage was reduced to a 4×4 block instead of a whole 16×16 macroblock.According to the data reuse strategy,the intermediate data storage was also reduced from a whole 16×16 macroblock to four 4×4 blocks.With an optimized pipeline design,the data access to bus was reduced efficiently.The resulting design could achieve 100 MHz with only gate counts of 14.2×103 by using 0.18 μm technology.Compared with former designs,the proposed deblocking filter architecture can achieve better performance with smaller hardware area.At 100 MHz,the proposed design can perform real-time deblocking filter for high definition video application of H.264.
On-Chip Implementation of Cascaded Integrator Comb filters (CIC) for DSP applications

Rozita Teymourzadeh,Masuri Othman

DOI: https://doi.org/10.48550/arXiv.1806.04568

2018-06-10

Abstract:This paper presents the design of CIC filters based on a low-pass filter for reducing the sampling rate, also known as decimation process. The targeted application for the filter is in the analog to digital conversion (ADC).The CIC is chosen because of its attractive property of both low power and complexity since it does not require multipliers. Simulink toolbox available in Matlab software is used to design and simulate the functionality of the CIC filter. This paper also shows how sample frequency is decreased by CIC filter and it can be used to give enough stop-band attenuation to prevent aliasing after decimation.

Signal Processing
The Design and FPGA Verification of Interpolation Filter Used in △-∑ DAC

CHEN Lei,HAN Yan

DOI: https://doi.org/10.3969/j.issn.1001-9146.2006.05.017

2006-01-01

Abstract:This paper describes a general structure,area-optimized interpolation filter used in the Delta-Sigma Digital-to-Analog converter(DAC) intended for the portable digital audio system.The whole filter system simulation,verilog implement and FPGA verification are processed,the signal-to-noise(S/N) achieves 115 dB and the total area is small enough which has good prospect for the audio applications.
Design of a Sigma-Delta Analog-to-Digital Converter Cascade Decimation Filter

Mao Ye,Zitong Liu,Yiqiang Zhao

DOI: https://doi.org/10.3390/electronics13112090

IF: 2.9

2024-05-28

Electronics

Abstract:As the current mainstream high-precision ADC architecture, sigma-delta ADC is extensively employed in a wide range of domains and applications. This paper presents the design of a highly efficient cascaded digital decimation filter for sigma-delta ADCs, emphasizing the suppression of high folding band noise and the achievement of a flat passband. Additionally, this study addresses the critical balance between filter performance and power consumption. An inserting zero (IZ) filter is incorporated into a cascaded integrator comb (CIC) filter to enhance aliasing suppression. The IZ filter and compensation filter are optimized using the particle swarm optimization (PSO) algorithm to achieve greater noise attenuation and smaller passband ripple. The designed filter achieves a noise attenuation of 93.4 dB in the folding band and exhibits an overall passband ripple of 0.0477 dB within a bandwidth of 20 KHz. To decrease the power consumption in the filter design, polyphase decomposition has been applied. The filter structure is implemented on an FPGA, processing a 5-bit stream from a 64-times oversampling rate and third-order sigma-delta modulator. The signal-to-noise ratio (SNR) of the output signal reaches 91.7 dB. For ASIC design, the filter utilizes 180 nm CMOS technology with a power consumption of 0.217 mW and occupies a layout area of 0.72 mm2. The post-layout simulation result indicates that the SNR remains at 91.7 dB.

engineering, electrical & electronic,physics, applied,computer science, information systems
Efficient VLSI Design and Implementation of Decimation Filter for 2nd ΣΔ A/D Converter

PENG Chungan,YU Dunshan,SHANG Tianxiu,SHENG Shimin

DOI: https://doi.org/10.3321/j.issn:0479-8023.2007.03.019

2007-01-01

Abstract:The authors describes an efficient design and implementation of a decimation filter for high resolution 2 nd ΣΔ A/D converter.A new universal multiplier-free VLSI structure is proposed to implement 2-time decimation for half bandfilters and a high-order invsinc corrector filter,the whole filter is realized without any multiplier or RAM or ROM,and the 2 nd ΣΔ A/D converter reaches a 16-bit resolution with low cost.
Design and Optimization of Decimation Filter in Σ-Δ A/D Converter

易锋,吴晓波

2009-01-01

Abstract:In order to reduce power dissipation and chip size of Σ-Δ A/D converter,an optimized method for Sinc filter was proposed based on the research and analysis of different implementation structures.Simulation and synthesis were performed based on TSMC's 0.18 μm CMOS process.Results showed that the area and power of the new structure were reduced by 36% and 50%,respectively,in comparison with traditional CIC structure.And finally,an optimization scheme for decimation structure was proposed based on the total power distribution of the decimation filter.
An Optimized Design for a Decimation Filter and Implementation for Sigma-Delta ADC

Yingying Cui,Jie Huang,Lingjuan Wu,Xiaoxin Cui,Dunshan Yu

DOI: https://doi.org/10.1109/edssc.2009.5394251

2009-01-01

Abstract:The area, speed and power consumption of over-sampled data converters are governed largely by the decimation filters in Sigma-Delta Analog/Digital converters(ADC) and multiplication is the core operation of the digital filter, so the performance of digital system is determined by multiplication. This paper compares four different popular methods: Conventional multiplications and additions; full custom distributed arithmetic (DA) scheme; Add-and-Shift method with CSD encoding; advanced sub-expression sharing algorithm. Each scheme is analyzed in detail including implementing process and the experimental results are given to evaluate each scheme. All of these implementations are aimed to implement using Design Compiler. Then this paper presents an optimized circuit for the decimation filter and the decimation filter for Sigma-Delta ADC is implemented using 0.35 mu m CMOS technology, with an approximate silicon area of 19mm(21).
Low Resource Consumption Design of Digital Decimation Filter

qian zebin,yan wei

DOI: https://doi.org/10.13209/j.0479-8023.2017.140

2018-01-01

Abstract:A digital decimation filter applied to audio Sigma-Delta ADC is designed. The filter adopts the design of multi-stage and multi-rate down sampling structure, in-band ripple of decimation filter is less than 0.06 d B overall, bandwidth is 21.6 k Hz, minimum working frequency is 10 MHz. Through the innovation of filter hardware architecture design, it effectively reduces the filter circuit area and power consumption. Chip test results show that the SNR is above 87.2 d B when processing PDM signals is at the down sampling rate of 64, 4 order Sigma-Delta modulation. Designed in SMIC’s 0.13 μm CMOS process, the decimation filter area is 0.146 mm2. Filter area is reduced by 58%, and power consumption is reduced by over 60% compared with the same type decimation filters.
A hardware-effective digital decimation filter implementation for 24-bit ΔΣ ADC

Yafei Ye,Ting Li,Zhihua Wang,Liyuan Liu,Dongmei Li

DOI: https://doi.org/10.1109/PrimeAsia.2011.6075059

2011-01-01

Abstract:A hardware-effective digital decimation filter implementation used in the 24-bit ΔΣ ADC for audio application is described in this paper. Composing of four comb filters and two half-band Finite Impulse Response (FIR) filters, the digital decimation filter uses multistage structure to relax the filter design. Since the multipliers are the most hardware consuming components in the digital filters, the coefficients of the FIR filters are coded by Canonical Signed Digit (CSD) which can make the filter multiplier-free. Meanwhile, time-multiplexing method is adopted in the filter to further reduce the hardware consumption. The proposed design is synthesized in 180nm CMOS process and occupies a die area of 1.44 mm2. This implementation is well suited for VLSI and can be applied to many other high resolution ΔΣ ADC.
Design and FPGA Implementation of a Reconfigurable Digital Down Converter for Wideband Applications.

Xue Liu,Xin-Xin Yan,Ze-Ke Wang,Qing-Xu Deng

DOI: https://doi.org/10.1109/tvlsi.2017.2748603

2017-01-01

IEEE Transactions on Very Large Scale Integration (VLSI) Systems

Abstract:This brief presents a field-programmable gate array-based implementation of a reconfigurable digital down converter (DDC) that can process input bandwidth of up to 3.6 GHz and provide a flexible down-converted output. The proposed DDC consists of a mixer and a resampling filter. The resampling filter can work at much higher clock rate. The reason is that all the single-cycle recursive loops in the resampling filter are pipelined by using either real/imaginary part-time multiplexing or parallel processing technique. With features like arbitrary sampling rate conversion, and dynamic configuration, the proposed design is highly flexible, so that it can generate a down-converted output with sampling rate, selectable within the range of 1 kS/s-225 MS/s. Moreover, the flexibility is further improved by being able to specify the output sampling rate and center frequency to a resolution of less than 1 S/s. The experimental results show that the proposed design can achieve the same functionality as the existing work but with fewer hardware resources.
A Down-Sample Design under Special Condition in High-Speed All-Digital System

Hongwei Sun,Jinshu Chen

DOI: https://doi.org/10.1109/IITA.2008.557

2008-01-01

Abstract:Digitalization and high-speed signal processing is the trend of electronic information and technology. In order to avoid unnecessary calculation, the sampled data in high-speed digital system have to be down-sampled. Three designs of down-sample are discussed and compared with each other in this paper so that people choose the most suitable plan in different works. One with FIR filters is a classical design and is applied widely. The other is an unfamiliar design which is applied directly to band-pass signal. Another is the CIC decimation filter design which is used in recent years. Specially, the theory and design technique of cascaded integrator-comb (CIC) filter cascaded interpolated second-order polynomial (ISOP) filter are analyzed. Simulation is done to validate the usefulness of compensating attenuation in pass-band of ISOP filter on CIC filter. The conclusion is that the system employs CIC decimation filter shows advantage over the other two plans in appliance and reserving resources. A combined down-sample design that can reduce the complexity of the entire system effectively is put forward based on the three designs above in the end.
The Design and Implementation of Fir Filter Based on Improved Da Algorithm

Jun Yang,Hongye Li,Zongjing Li,Qing Han

DOI: https://doi.org/10.2991/cmfe-15.2015.193

2015-01-01

Abstract:FIR filter is widely used in the fields of signal processing with high fidelity. In the design of FIR filter the traditional algorithm such as serial DA algorithm, parallel DA algorithm and combined series and parallel DA algorithm are all not so suitable, which has lots of shortcomings. In this design, we improve the DA algorithm and uses the 4-BAAT method which optimizes the structure of LUT(look-up table) to realize the FIR filter. The process of FIR simple tap coefficients is achieved by the operation of shifting and reversing of symbol bit, which can pick up the speed and save the logic resources. This design adopts the Verilog HDL language, using FDA Tool to determine and quantify the coefficients with the given filter parameters. Then it uses Quartus 118.0 to integrate and wire, and Modelsim to simulate and verify. Compared with the filter achieved by standard DA algorithm, this filter reduces complexity, saves logic resources and picks up the speed besides it has the advantages of good reconfiguration, simple hardware structure and high real-time.
An Area-Efficient Implementation of Multistage Decimation Filter for Delta-Sigma Analog-to-Digital Converter

Chen-xi DENG,Hong-ming CHEN,Yu-hua CHENG

DOI: https://doi.org/10.3969/j.issn.1681-5289.2013.06.003

2013-01-01

Abstract:In this paper, an area-efficient implementation of a multistage decimation filter for audio delta-sigma ADC is presented. The decimator with a decimation ratio of 256 has less than 0.005dB passband ripple and 100dB stop band attenuation. It has an audio passband of 0-20kHz and outputs 16-bit resolution signal at 48kHz. With an area-efficient architecture involving RAM and ROM, and dedicated instruction scheduling through 256 steps in a cycle, the decimator is synthesized with less than 300 LUTs and less than 160 Slices on Xilinx FPGA. Unlike serial or partly-serial architecture where computing rate is usually higher than input sampling rate, the computing rate or clock rate here is exactly equal to the input sampling rate, which can simply the overall ΣΔADC design and lower the power consumption. The programmability brought about by the RAM and ROM in the architecture makes the filter improvable for adaptive filtering. At last, the simulation result of RTL model in Modelsim is verified by Matlab\ Simulink program.
Low-Power and Hardware Efficient Decimation Filters in Sigma-Delta A/D Converters

Hengfang Zhu,Xiaobo Wu,Xiaolang Yan

DOI: https://doi.org/10.1109/edssc.2005.1635362

2005-01-01

Abstract:The power and area formulas for four popular Sinc-filter structures used in decimation filters were discussed in this paper. It was proved that the formulas are very useful in power or area estimation and comparison. The circuit implementations of each structure are illustrated. And the power and area comparisons of the four structures were simulated and analyzed. A further optimization technology for one of the efficient filter structures was also proposed.
Design of the Decimation Low Pass Filter Used in a 14-B 1.5625 MHz Sigma-Delta A/D Converter

Yi Ting

2004-01-01

Abstract:The design of a decimation low pass filter used in a 14-b 1.5625 MHz Sigma-Delta A/D converter is presented in this paper. In the design of this filter, at all levels from architecture to hardware implementation, techniques are applied to optimize the circuit structure and reduce the circuit complexity in order to minimize the power dissipation and area. Finally, the circuit is synthesized targeted to 0.6 μm CMOS technology. The simulation result proves that its performance meets the design specification.

Decimation Filter Design for DDC and Implementing It with FPGA

Decimation Filter Design in Sigma-delta ADC

The Design and FPGA Verification of a General Structure, Area-optimized Interpolation Filter Used in /spl Delta/-/spl Sigma/ DAC

An Enhancement of Decimation Process using Fast Cascaded Integrator Comb (CIC) Filter

Design and Implementation of a Modified High Performance and Low Power CIC Interpolation Filter

Design of a HDTV Audio Decoder on a Fixed Point DSP Chip

Implemented Architecture Design of Deblocking Filter for H.264

On-Chip Implementation of Cascaded Integrator Comb filters (CIC) for DSP applications

The Design and FPGA Verification of Interpolation Filter Used in △-∑ DAC

Design of a Sigma-Delta Analog-to-Digital Converter Cascade Decimation Filter

Efficient VLSI Design and Implementation of Decimation Filter for 2nd ΣΔ A/D Converter

Design and Optimization of Decimation Filter in Σ-Δ A/D Converter

An Optimized Design for a Decimation Filter and Implementation for Sigma-Delta ADC

Low Resource Consumption Design of Digital Decimation Filter

A hardware-effective digital decimation filter implementation for 24-bit ΔΣ ADC

Design and FPGA Implementation of a Reconfigurable Digital Down Converter for Wideband Applications.

A Down-Sample Design under Special Condition in High-Speed All-Digital System

The Design and Implementation of Fir Filter Based on Improved Da Algorithm

An Area-Efficient Implementation of Multistage Decimation Filter for Delta-Sigma Analog-to-Digital Converter

Low-Power and Hardware Efficient Decimation Filters in Sigma-Delta A/D Converters

Design of the Decimation Low Pass Filter Used in a 14-B 1.5625 MHz Sigma-Delta A/D Converter