Abstract:AbstractThe search for suitable friction materials for high-speed train is an attractive but difficult problem. In recent years, a variety of different novel friction materials were fabricated to meet the aims of high loads and speeds under ambient environment. Carbon fiber-reinforced carbon composites (C/C), carbon fiber-reinforced silicon carbide composites (C/C-SiC) and metallic composites fabricated by powder metallurgy are three excellent materials among them. Here a comparison of these three different materials working as brake pads, coupled with high-density C/C-SiC brake disk, was described. All the experiments were conducted using the same procedure with increasing initial braking speed (the rotation speed of brake disk at the beginning of braking process) from 30 to 59 m/s and constant load of 1.25 MPa, simulating the real working condition of high-speed train. The coefficient of friction (COF) and wear rates of three materials were compared and analyzed. During experiments, the COF of metallic and C/C pads remains nearly constant at 0.31 and 0.22, respectively, with increasing braking speed, while that of C/C-SiC exhibits a parabola. These different trends of COF may be attributed to the distinctive forming processes of friction film on the top of contact surfaces. Meanwhile, the wear rates of metallic composites increase rapidly from 683 to 1803 mm3/MJ with initial braking speed, while C/C-SiC presents the highest wear loss of 1887 mm3/MJ at 49 m/s and lowest value of 315 mm3/MJ at 59 m/s. Interestingly, the wear rate of C/C composites, due to the appropriate bonding strength of matrix/fiber and relatively high shear stress, decreases from 3698 to 903 mm3/MJ with increasing initial braking speed, which does not consist with pre-existing paper. Thus, metallic pads presented the lowest wear rates at lower speed (<49 m/s) but the highest at high speed, while C/C-SiC composite pads showed the greatest wear resistance at high speed. This investigation of three different friction materials will enhance our understanding of these friction materials and benefit the selection and safe application of high-speed train friction materials.

Effect of Braking Pressure and Braking Speed on the Tribological Properties of C/SiC Aircraft Brake Materials

Fading behavior and wear mechanisms of C/C–SiC brake disc during cyclic braking

Influence of Braking Conditions on Tribological Performance of Copper-Based Powder Metallurgical Braking Material

Friction and Wear Mechanics of Fe-Based PM Pad Paired with Carbon Fiber-Reinforced Silicon Carbide (C/C-SiC) Disk Under High-Speed Braking

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Effects of Sintering Temperature on Bending Property of C-F/Sic Brake Material

Effects of Sintering Temperature on Bending Property of C<sub>f</sub>/SiC Brake Material

Tribological performance and composition optimization of semi-metallic friction materials applied for carbon ceramic brake disc

Dry sliding tribological behavior of C/SiC under different load and speed

Comparison of Friction and Wear Behavior Between C/C, C/C-SiC and Metallic Composite Materials

Coupled thermal-structural analysis of an axle mounted C/C-SiC brake disc for high-speed trains

Effect of the pin temperature and SiC reinforcement on dry sliding tribological behavior of aluminium based silicon carbide metal matrix composite (Al-SiC) using Taguchi approach

The Microstructure and Wear Characteristics of Cu–Fe Matrix Friction Material with Addition of SiC

Mechanical and tribological properties of C/C–SiC ceramic composites with different preforms

Braking Performance of Fe-Based and Cu-Based Powder Metallurgy Pads Paired with C/C-SiC Disk on Full-Scale Dynamometer

Modifying C/C–SiC brake pads with different Fe–Si alloy phases to improve the wear resistance of full-carbon/ceramic brake pair

Comparison of the Braking Behavior Among Cast Steel, Carbon/Carbon (C/C) and Carbon/Carbon-Silicon Carbide (C/C-SiC) Materials Mated with Copper-Based Composites

Frictional behavior of selective laser melted brake discs under high-speed braking

The effect of alumina-based sintering aid on the microstructure, selected mechanical properties, and coefficient of friction of Cf/SiC composite prepared via spark plasma sintering (SPS) method

Ceramic waste SiC particle-reinforced Al matrix composite brake materials with a high friction coefficient

Effects of carbon fiber dispersion on bending property of Cf/SiC brake materials