Abstract:Base isolation provisions in ASCE 7 Standard have been historically shown to be conservative in estimating seismic demands. New torsional bearing base isolation displacement expressions have been proposed recently by the latest ASCE 7–16 Standard. This study compares the accuracy of the new ASCE 7–16 static-based isolation expressions for additional bearing displacement due to plane torsion to the response obtained using simplified structural dynamics' plane torsion theory expressions. In addition, it conducts a parametric study to assess the effect of accidental eccentricity, damping ratio, and plan aspect ratio on the accuracy of ASCE 7–16 bearing displacement expression. The results showed that the ASCE 7–16 undamped displacement estimations improved compared to the significant conservatism of ASCE 7–10 by 7–33% depending on the eccentricity condition and ratio, which may further promote the use of base isolation in the US as a seismic hazard mitigation solution. However, the study also revealed that a considerable conservatism of the new base isolation bearing displacement provisions of ASCE 7–16 still exists in some cases, which ranged from 52 to 105% in the case of three equal fundamental frequencies and 5–20% in the case of equal lateral frequency and distinct torsional frequency. The study also showed that the ASCE 7–16 conservatism is proportional to the eccentricity and is more pronounced with biaxial eccentricity compared to single eccentricity. Furthermore, the results show that ASCE 7–16 expression accuracy significantly declines with damped systems with a possibility of un-conservative estimation of bearing displacements that can reach 25–40% with larger eccentricities. In addition, the ASCE 7–16 torsional displacement was shown to be inversely proportional to the plan aspect ratio with a discrepancy that can reach ± 20%. The study also exhibited that the ASCE 7–16 torsional displacement conservatism is slightly affected by increasing damping ratio above 4%.

Simplified Calculation Approach of Torsionally Coupled Seismic Response for Base-Isolated Eccentric Structures

A Direct Displacement-Based Design Procedure for Base-Isolated Building Structures with Lead Rubber Bearings (Lrbs)

Analysis on the Torsion Parameters of L-shaped High-Rise Isolation Buildings

Efficient and Accurate Method for Calculating the Stochastic Seismic Response of A Nonproportionally Damped Structure

SIMPLIFIED METHOD FOR CALCULATING DYNAMIC CHARACTERISTICS OF SOIL-ISOLATED STRUCTURE SYSTEM

Accuracy Comparison of Engineering Methods for Calculating Dynamic Time History Response of Vibration-Isolated Buildings

Base shear determination using response-spectrum modal analysis of multi-degree-of-freedom systems with soil–structure interaction

An improved Chinese load code method for the evaluation of wind‐induced base shear force on base‐isolated buildings

Torsion in symmetric buildings due to soil‐structure interaction: A discussion on code values of accidental eccentricity factor in seismic design

Stochastic Seismic Response and Reliability Analysis of Base-Isolated Structures

Analytical and numerical investigations of base isolation system with negative stiffness devices

A Simplified Method Of Seismic Response Analysis Of Soil-Underground Structure System

IDA-based Seismic Fragility Analysis for One-story Asymmetric Plan Systems Under Bi-directional Earthquake Motions

Multi-Performance Economical Optimization of Base Isolation System with Tuned Inerter Negative Stiffness Damper Subjected to Non-Stationary Seismic Excitation

Analysis of Soil-Structure Interaction (ssi) Effects on Seismic Response of Base-Isolated Structures

Critical Response of Nonlinear Base-Isolated Building Considering Soil-Structure Interaction Under Double Impulse as Substitute for Near-Fault Ground Motion

Design and Analysis of the Base-isolated Structure

Analysis On Vertical Tank Fluid-Solid Coupling Vibration And Base Isolation Dynamic Response

Seismic Isolation Layout Optimized of Mid-Rise Reinforced Concrete Building Frame Structure

Assessment of ASCE 7–16 Seismic Isolation Bearing Torsional Displacement

A practical simulation method of spatially correlated earthquake ground motions