Abstract:3D printing has revolutionized solid oxide fuel cell (SOFC) by introducing complicated structure and new functionalities that cannot be realized using traditional preparation process. This work provides guide and insights into the application of direct-writing 3D printing to fabricate the patterned electrolyte|electrode interface for the anode-supported SOFC using 3 mol % yttria-stabilized zirconia-nickel oxide (3YSZ-NiO) as the anode substrate material. The parameters that affected the shaping and performance of SOFC including the rheological properties of 3YSZ-NiO anode paste, the printing parameters, and the heat treatment process of the pre-sintered anode substrate were evaluated. The prepared 3YSZ-NiO paste exhibited a typical shear-thinning characteristic, "yielding" solid-like behavior, and time- and temperature-independent stability performance, which ensured the paste suitable for extrusion while allowing the shape of the printed body to be maintained after extrusion during the direct-writing printing process. The as-prepared anode paste, combined with the obtained values of 0.1 MPa, 100 mm s −1 , 100 rpm, and 0.3 mm for printing parameters of the extrusion pressure, the printing speed, the screw speed, and the nozzle diameter, respectively, as well as the devised heat treatment program for the pre-sintered 3YSZ-NiO anode substrate, successfully produced defect-free corrugated anode substrates. The cell made from the as-mentioned anode substrate showed an open circuit voltage of 1.02 V and a maximum power density of 619.44 mW cm −2 at 850 °C, which was comparable to the other identical cells fabricated by traditional and other 3D printing processes. Using the 3D printing process shown here, the preparation time of patterned anode substrate can be reduced and simplified.

NiO+YSZ Anode Substrate for Screen-Printing Fabrication of YSZ Electrolyte Film in Solid Oxide Fuel Cell

YSZ Thin Films Prepared by a Novel Powder Coating Process on Porous NiO-YSZ Cermet

Screen-Printed Thin Ysz Films Used As Electrolytes for Solid Oxide Fuel Cells

A Study of the Process Parameters for Yttria-Stabilized Zirconia Electrolyte Films Prepared by Screen-Printing

Fabrication and Performance of Anode-Supported YSZ Films by Slurry Spin Coating

Fabrication and Performance of Anode-Supported Electrolyte Thin Films SOFCs

Effect of Starting Powder on Screen-Printed Ysz Films Used As Electrolyte in Sofcs

Anode-supported YSZ Film Fabricated by Using Micron-Sized Particles

Novel Co-precipitation method to synthesize NiO-YSZ nanocomposite powder for solid oxide fuel cell

Performance of NiO-YSZ Anode with NiO Powder Synthesized by Precipitation Method

Fabrication of an Anode-Supported Yttria-Stabilized Zirconia Thin Film for Solid-Oxide Fuel Cells Via Wet Powder Spraying

Effect of NiO/YSZ Compositions on the Co-Sintering Process of Anode-Supported Fuel Cell

Thin Yttria-Stabilized Zirconia Electrolyte and Transition Layers Fabricated by Particle Suspension Spray

Fabrication and Performance Test of Solid Oxide Fuel Cells with Screen-Printed Yttria-Stabilized Zirconia Electrolyte Membranes

Fabrication and Study on Ni1−xFexO-YSZ Anodes for Intermediate Temperature Anode-Supported Solid Oxide Fuel Cells

Fabrication and evaluation of anode and thin Y2O3-stabilized ZrO2 film by co-tape casting and co-firing technique

Development of yttria-stabilized zirconia thin films via slurry spin coating for intermediate-to-low temperature solid oxide fuel cells

Effect of Pre-Sintering Treatment of Anode Substrate on the Densification and Flatness of Ysz Electrolyte by Suspension Spray

Facile preparation of patterned anode substrate for solid oxide fuel cells by direct-writing 3D printing technology

Co-sintering anode and Y 2O 3 stabilized ZrO 2 thin electrolyte film for solid oxide fuel cell fabricated by co-tape casting

Preparation of Ni/Ysz Anode Material Using Gel-Tape Casting and Performance Analysis