Abstract:Polyethylene terephthalate (PET) is a largely-produced polymer worldwide. However, its extensive waste generation and resistance to degradation pose significant environmental concerns. Consequently, there is considerable interest in researching enzymatic degradation of PET. Relevant studies have shown that the addition of a carbohydrate binding module (CBM) can increase the affinity between the enzyme and the substrate, enhancing the enzyme's degradation ability. In order to develop more efficient PET hydrolytic enzymes, this study introduced carbohydrate binding domains (CBMs) from different families with different substrate affinities into the PET-degrading enzyme LCC-ICCG. High crystallinity PET powder and amorphous PET film were used as substrates to characterize the degradation efficiency of the modified enzymes, aiming to explore the enzyme with the optimal degradation ability. The results showed that the fusion of type B CBM reduced the degradation rate and Tm value of the enzyme towards PET, while the introduction of type A and type C CBMs significantly improved the degradation rate of the enzyme towards the film-like substrate. The degradation rate and Tm value of PET were also enhanced, especially with the fusion enzyme LCC-ICCG-CBM9-2, which showed an over 10-fold increase in the degradation rate compared to the original enzyme LCC-ICCG. Therefore, this study demonstrates that by introducing type A and type C CBMs, the degradation rate and thermal stability of LCC-ICCG towards film-like PET can be improved, addressing the issue of its low activity and enabling more effective PET degradation. This research provides support for plastic degradation technology and contributes to environmental conservation efforts.

Surface modification of poly(ethylene terephthalate) via hydrolysis and layer-by-layer assembly of chitosan and chondroitin sulfate to construct cytocompatible layer for human endothelial cells.

Layer-By-Layer Assembly of Biomacromolecules on Poly(Ethylene Terephthalate) Films and Fiber Fabrics to Promote Endothelial Cell Growth

Surface tailoring of poly(ethylene terephthalate) via ligand-tethered comb-like PEG to enhance endothelialization

Layer-by-layer Assembly to Modify Poly(l-Lactic Acid) Surface Toward Improving Its Cytocompatibility to Human Endothelial Cells.

Construction of anti-adhesive and antibacterial multilayer films via layer-by-layer assembly of heparin and chitosan.

Modification of Amorphous Poly(ethylene Terephthalate) Surface by UV Light and Plasma for Fabrication of an Electrophoresis Chip with an Integrated Gold Microelectrode

Construction of phospholipid anti-biofouling multilayer on biomedical PET surfaces

[Enhancing PET Degradation Efficiency Through Fusing Carbohydrate-Binding Modules in LCC-ICCG].

Silk fibroin immobilization on poly(ethylene terephthalate) films: comparison of two surface modification methods and their effect on mesenchymal stem cells culture.

Surface Functionalization of Poly(ethylene terephthalate) Film and Membrane by Controlled Wet Chemistry: Chemical Characterization of Carboxylated Surfaces

Surface Tailoring of PET via Immobilization of Comb-shaped Poly(ethylene glycol) for Promoting Endothelial Cell Compatibility

Surface modification of polypropylene microporous membrane via self-assembly and UV-crosslinking of lecithin and analysis of surface properties

Surface Modification of Poly(tetrafluoroethylene) Films Via Plasma Treatment and Graft Copolymerization of Acrylic Acid

Enzyme biocatalyst route to superhydrophobic surfaces on microstructured poly(ethylene terephthalate) film

Construction of antithrombotic and anti-microbial ultra-thin structures on polyethylene terephthalate implant via the surface grafting of heparin brushes

Promotion of Endothelial Cell Adhesion and Antithrombogenicity of Polytetrafluoroethylene by Chemical Grafting of Chondroitin Sulfate

A Novel Approach towards the Preparation of Silk-Fibroin-Modified Polyethylene Terephthalate with High Hydrophilicity and Stability

Anti-biofouling and functionalizable bioinspired chitosan-based hydrogel coating via surface photo-immobilization

Surface Engineering Of Poly(Dl-Lactide) Via Electrostatic Self-Assembly Of Extracellular Matrix-Like Molecules

Uniform-saturation modification for hydrophilicity improvement of large-scale PET by plasma-electrified treatment

Surface Engineering of Poly(d,l‐lactic Acid) by Entrapment of Chitosan‐based Derivatives for the Promotion of Chondrogenesis