Design of Information Querying System for Vibration Standards

LIANG Jia-rui,MAO Le-shan

2013-01-01

Abstract:A vibration standard information query system via VC++6.0 is built,which can improve the implementation validity of vibration standard in maintenance of industrial device.

What problem does this paper attempt to address?

Development Of Automatic Vibration Calibration System

Wen He,ShuShi Jia

2002-01-01

Abstract:A set of measuring and controlling instrument that integrates functions of a sine-wave generator, an AC digital voltmeter and a frequency-rate counter, and a suit of specially-designed software are used to make it easy for users to get the characters of transducers such as sensitivity, linearity and frequency response. Both the hardware and software schemes of the instrument is analyzed and evaluated. Experimental results prove that the system is suitable for calibration of vibration transducers. The system has greatly improved the efficiency of the calibration at lower cost.
Study and Establishment of the National Standard of the Ultra-low frequency Vibration

Mei YU,Wen HE,Ai-dong LIU,Ming-de MA,Li-feng YANG,Ai-bin ZUO,Hong-bo HU

DOI: https://doi.org/10.3969/j.issn.1000-1158.2011.02.01

2011-01-01

Abstract:According to the research status and application requirements for ultra-low frequency vibration standard at home and abroad, the national standard device for vibration magnitude and phase was studied and established. The ultra-low frequency range is 0.002 Hz to 160 Hz. The maximum peak-to-peak value of amplitude is 1m.The maximum load is 30 kg. The distortion of acceleration waveform is less than 1%.The structure composition of the device and the key technologies solved are introduced. The design project of the long-stroke horizontal vibrator, the negative-feedback control technology, the pipeline dragging synchronous tracking control system and the laser vibration measuring system are described. The main technical specifications of the standard device and the results of comparison experiment are given. The establishment of the national standard device can solve the quantity traceability problem of the ultra-low frequency vibration metrology.
The Design of Control Software in Vibration Calibrate System

王光庆,何闻,贾叔仕

DOI: https://doi.org/10.3969/j.issn.1001-4551.2001.05.068

2001-01-01

Abstract:In this article,the design of control software is discussed detailedly,which is used in the Vibration-Calibrate-System,the general construction and precept of control software are put forward,the experiments prove that the control software can meet the requirements of calibrating vibration sensors,very well and also improves the automation of calibrating vibration sensors.
Testing System of Characteristics of Electrical Vibration Table

XU Hui,MOU Xu-dong,SHU Xiao-wu

DOI: https://doi.org/10.3969/j.issn.1004-1699.2006.01.065

2006-01-01

Abstract:A system which can test the characteristics of electrical vibration table is put forward, with advantages of simple structure, high resolution and adapting to all the vibration mode measurements. In the system, both auto-collimating beam and position sensitive detector are introduced to detect tiny angle of electrical vibration table. After data being transferred through USB universal bus to PC, we can obtain the characteristic curve of table angular-rate by digital processing . The system contains three parts, including auto-collimating optical system, PSD' signal processing unit and data processing system. By analyzing the errors of all the three parts, the angle resolution of the system is 9.90×10 -5 degree. The test experiment results show that the system can meet the application request in the bias stability detection of high-resolution angular-rate sensor in vibration mode.
Research of automatic control system for ultralow frequency vibration calibration

WANG Zhi-peng,HE Wen,YU Mei,SHEN Run-jie

DOI: https://doi.org/10.3969/j.issn.1001-4551.2011.06.014

2011-01-01

Abstract:Aiming at the demerits of time-consuming and low efficiency during the process of ultralow frequency vibration calibration,an automatic ultralow frequency vibration calibration system based on personal computer and virtual instrument was presented.The system was consisted of ultralow frequency standard vibrator,power amplifier,laser vibrometer,displacement transducer,signal generator,universal counter,data acquisition card,computer,control software,etc..The strategy which via combining the method of linear approximation and step-by-step frequency shift could make the vibrator reach the pre-set vibration level quickly and precisely.The experiment results show that the system is suitable for the calibrating ultralow frequency vibration transducers very well and improves the automation of ultralow frequency calibrating vibration.
Design, Simulation and Development of a Broadband Electromagnetic Angular Vibrator

Wen He,Bo Tang,Shushi Jia

DOI: https://doi.org/10.3233/jae-170132

2018-01-01

International Journal of Applied Electromagnetics and Mechanics

Abstract:A novel broadband electromagnetic angular vibrator with a disk-type rotating coil is brought forward to satisfy the calibration demand of various angular vibration transducers. First, the structure of the electromagnetic angular vibrator is introduced, and the electromechanical coupling equation is established to reveal the relation between the input and output of the vibrator. Then, in order to realize wide operating frequency range and low total harmonic distortion of angular motion output, four key technologies have been adopted in our angular vibrator, which include a rotating coil made of a multilayer printed circuit board, a rotating component with a high torsional resonant frequency, a double-magnetic-source magnetic circuit with pole shoes and a linear suspension device with large angular displacement. Finally, the performance indexes and the total harmonic distortion of output motion waveform from the developed broadband electromagnetic angular vibrator are measured. The test results show that the angular vibrator can output maximum angular displacement of 60 degrees and maximum angular acceleration of 2000 rad.s(-2), and the total harmonic distortion of the angular acceleration waveform from the developed vibrator is less than 1% over its whole operating frequency range from 0.01 to 1200 Hz, which has met the requirement of the angular vibrator for calibration according to ISO 16063-15: 2006.
Design and Application of Ultra-low Frequency Vibration Laboratory

Yuwei WANG,Jin HAN,Wei SUN,Wen HE

DOI: https://doi.org/10.13512/j.hndz.2017.02.004

2017-01-01

Abstract:According to the current research status and application requirements of ultra-low frequency vibration standard devices, a vibration standard device is set up in Sichuan Earthquake Agency, whose frequency range is from 0.002 Hz to 160 Hz, and amplitude of peak to peak is 0.1m, and load is 15 kg, and waveform distortion is less than 1%. The paper analyzed the design proposal and parameter selection for the ultra-low frequency vibration standard laboratory, and introduced in detail the structure of the device and the design of the base. Finally, the test results show that the device could meet the demand of calibrating seismometers in our bureau.
Design of tractor vibration testing system

LI Min-tong,YANG Qing,CHEN Jun

DOI: https://doi.org/10.13207/j.cnki.jnwafu.2010.05.009

2010-01-01

Abstract:【Objective】 This paper designs a practical testing system for acquiring and analyzing the tractor vibration signals.The system can supply a platform for studying the tractor vibration characteristics.【Method】 The data inquiring part was designed with DaqLab/2005,LC0201,transducer,and computer.Based on the theories of signals processing such as frequency spectrum analysis,wavelet,and chaos analysis,the analyzing part was completed with MATLAB.【Result】 The signal acquisition part can collect the tractor vibration signals when the tractor is excited at different frequencies.The signal analyzing part can complete the following work such as pre-processing,correlation analysis,frequency spectrum analysis and chaos analysis for nonlinear vibration signals.In order to verify the flexibility of the testing system,some experiments were done with Shanghai-50 tractor.The experiment results were given in this paper.These results proved that the system can realize the requirements.【Conclusion】 The testing system can be used for studying the tractor vibration characteristics.
Design and Implementation of Vibration Test Control System of Multi-Exciter Synchronization

CHEN Jia-yan,ZHOU Jian-chuan,CHEN Zhang-wei,HE Hui-nong

DOI: https://doi.org/10.3969/j.issn.1001-506x.2010.12.37

2010-01-01

Abstract:It is difficult to achieve the uniformity of vibration and stress distribution for slender specimens such as missiles.In order to complete the vibration test requirements,a multiple shaker is needed to excite them synchronously,and a multi-exciter synchronization vibration control system is implemented.A system equilibrium synthesis is presented to make up for deficiencies of different methods for random vibration test control algorithm.A control system is implemented with a hardware architecture of multiple digital signal processor(DSP) and peripheral component interconnect extensions for instrumentation(PXI) bus and a software architecture of multi-level modular.The related experiment result shows that the proposed control algorithm is effective and the system structure has a good expansibility.The control system can meet the vibration test requirements and has a certain practical value.
The Design of the Virtual Testing System of Vehicle Vibration Based on VR

MA Jun-fu,ZHOU Xiao-jun,XU Zhi-nong,CHI Jun,SHANG Jun-min

DOI: https://doi.org/10.3969/j.issn.1001-2265.2007.10.017

2007-01-01

Abstract:The concept and the theory model of the virtual testing based on virtual reality are studied.In terms of the mapping relation between the vehicle vibration testing system and the virtual testing system of vehicle vibration based on virtual reality(VTSVVBVR),the system framework design and the implementation method of the VTSVVBVR,which consists of virtual reality subsystem,modeling subsystem and virtual instrument subsystem,are proposed.The VTSVVBVR is designed,and the display of the virtual testing results of the vehicle vibration is presented,which has shown that the theory model of the virtual testing based on virtual reality is suitable for the VTSVVBVR design,and the vehicle vibration and its signals of time domain and frequency domain could be observed simultaneously in three observation models respectively by the aid of the system.
Design and Realization of System Software for Vibration Sources Signal Separation of Gearbox

Shixi Yang

2008-01-01

Abstract:Owing to coupling of vibration sources signals of gearbox,that made fault diagnosis difficult,the software was developed by LabVIEW and MATLAB for the separation of vibration sources signals of gearbox.The algorithms of ICA were programmed and formed in the structure of COM in MATLAB,and the algorithm of wavelet packet decomposition and reconstruction was programmed in LabVIEW,both of them were used as a model in LabVIEW,the independent signal was separated by the system which is good for the source identification and fault diagnosis.
Development and Application of Steam Turbine Vibration Sensor Fault Diagnosis and Calibration Instrument

Li-ping YANG,Chao SHEN,Wei-Ping HUANG,Jun LIANG

DOI: https://doi.org/10.3969/j.issn.1002-1841.2017.06.043

2017-01-01

Abstract:Structure,design,technology and field applications of steam turbine vibration sensor fault diagnosis and calibrator equipment were proposed.Based on LabVIEW,interfaces of host computer and console computer and amplitude domain,time do-main,frequency domain analysis model of detective signals were developed. Advantech data collection and signal conditioning modules were used to achieve connection the instrument with bearing vibration sensors,shaft vibration sensors keyphasor sensors and data collection.Fault analysis and diagnostic algorithms and database settings which were used to store collection data were realized with MATLAB.With the comprehensive field test,it is proved that online monitoring,signal analysis and fault diagnosis of vibration sensors at field can be done with this equipment.After transition,it can be used as an online reliable steam turbine vibra-tion monitoring tool in thermal power plants,nuclear power plants and hydropower plants and some other fields with large rotating machinery vibration.
Design and Analysis of Crushing Mill Base Vibration Isolation

Xiao-ping CHEN,Ying-wu YANG,Bai-sheng WANG,Xiao-qian QIAN

DOI: https://doi.org/10.3969/j.issn.1671-7147.2005.04.019

2005-01-01

Abstract:According to the introduction book of crushing mill, the weight of crushing mill base should be 8~10 times machine weight. But this project item does not achieve requirement of introduction book of crushing mill leading to social effects of vibration pollution. We design a active vibration isolation scheme making a pedestal which is set on the vibration isolaters to reduce the diffusing energy. This scheme is effective and vibration level of measuring point is less than acceptable value in ISO. Therefore, the paper has reference value to similar cases.
Design and Development of Test and Control System for Hydraulic Steering Control Unit Based on Virtual Instrument

Lu Qianqian,Wei Jianhua,Ruan Jian

DOI: https://doi.org/10.4028/www.scientific.net/amm.490-491.1092

2014-01-01

Applied Mechanics and Materials

Abstract:A system combined the function of Industrial Computer, PLC, virtual instruments, sensors and data acquisition was designed and developed for testing and controlling of hydraulic steering control unit, which can achieve automated data acquisition, data processing, test results judgment, false alarms and etc. with the development of computer and science. The software of test system was designed through LabVIEW, and by using module design method, error detection, modify and maintenance of the software turn to be simple and the software become more robust. The system also adopted shielding and filtering with combination of hardware and software to improve test accuracy which reduces test error caused by operators and improve test efficiency.
Design of Spectra Instant-Collection System Based on VB 6.0

Jianguo Lü

2004-01-01

Abstract:A novel spectra instant-collection system developed with Visual Basic 6.0 is introduced. The system provides single and continued working styles for the spectra collection under the cooperation of spectrometer and step-motor, therefore, the operation of spectra collection can be simplified greatly. The experimental result shows that it has some useful reference value for the design of serial communication and USB master-slave system.
Study on Hydroelectric Units Vibration Monitoring and Analysis Based on Virtual Instrument

崔宇涛,南海鹏,张伟,苏立

DOI: https://doi.org/10.3969/j.issn.1674-3814.2008.11.014

2008-01-01

Abstract:The Lab View,a mature measurement automation software,was combined with SQL Server 2000 as the software platform,based on which a system of vibration monitoring and fault analysis was developed.The proposed system was applicable to the hydropower units,by which the user can observe component's vibration conditioning simply and clearly.With the system's analyzing tools the user can identify the fault source.It was shown by practical application that the system has better reliability and practicability.
Design and Implementation of Virtual Test System Based on LabWindows/CVI

Liang Wang

2009-01-01

Abstract:VxWorks can not provide friendly graphical user interface like Windows system,and developing the graphical interface under VxWorks system has a high degree of difficulty and workload.According to the problems above,a useful method developed by LabWindows/CVI 8.5 is designed to test real-time simulation computer running on VxWorks.The method is successfully applied to the semi-physical simulation test for a certain type of plane,and it is proved useful in checking the I/O system of simulation computer.Quite a practical implementation is provided for diagnosing fault in I/O system for future.
The design of vibration testing system based on lab VIEW for wind turbine

Yongshan Ding,Dongxiang Jiang,Liangyou Hong,Qian Huang

2007-01-01

Abstract:This paper presents a wind turbine vibration testing system based on Lab VIEW with an introduction to the research background. Then, the paper analyzes the structure of the hardware system consisting of a small wind turbine, rotor experiment bed, vibration sensors, a data acquisition box and a computer. Also, the paper discusses the software function in detail, which applies the module design thoughts including real-time monitoring, off-line data analysis, and trend analysis and fault simulation. The software system can display time-wave, spectrum, axial track and trend figure and so on. In addition, the application on vibration data acquisition and analysis is implemented based on present testing system. At the same time, the familiar vibration faults, misalignment of rotor and radial rubbing of rotor, are produced and tested artificially. Finally, the system application foreground is discussed in terms of data acquisition, data analysis and fault diagnosis of wind turbine and other rotating machines.
Design and Implementation of Surveying Files Management and Query System Based on Web

MENG Chuan-ping,YANG Zheng-yin,XU Wan-jin

DOI: https://doi.org/10.3969/j.issn.1674-5019.2010.01.009

2010-01-01

Abstract:Design and Implementation of surveying files management and query system based on web is an application developed to solve the problems of lacking spatial region query and web query in traditional such systems.It is oriented to manage and use the surveying data.This system realizes systematization、standardization and automation of surveying files management,which can not only offer centralized management on the server but also distributed query on the client,with the purpose of increasing the efficiency of surveying files management and producing.
Study for Vibration Measurement and Failure Diagnostics System for CNC Milling Machines Based on LabVIEW

Shuangli An,Yafei He,Rui Qian,Xiaohang Liu

DOI: https://doi.org/10.4028/www.scientific.net/amr.189-193.1180

2011-01-01

Advanced Materials Research

Abstract:This paper presents a proposed system based on LabVIEW for data acquisition and monitoring of manufacturing process in machine tools with CNC. It was applied to evaluate work piece dimension and failure analysis in real time. The proposed system was developed and tested initially in a CNC milling machine with open architecture. Furthermore, it can be extended to other machines and processes, lines or cells of mass production as well. And it was applied in some factories and workshops now.

Design of Information Querying System for Vibration Standards

Development Of Automatic Vibration Calibration System

Study and Establishment of the National Standard of the Ultra-low frequency Vibration

The Design of Control Software in Vibration Calibrate System

Testing System of Characteristics of Electrical Vibration Table

Research of automatic control system for ultralow frequency vibration calibration

Design, Simulation and Development of a Broadband Electromagnetic Angular Vibrator

Design and Application of Ultra-low Frequency Vibration Laboratory

Design of tractor vibration testing system

Design and Implementation of Vibration Test Control System of Multi-Exciter Synchronization

The Design of the Virtual Testing System of Vehicle Vibration Based on VR

Design and Realization of System Software for Vibration Sources Signal Separation of Gearbox

Development and Application of Steam Turbine Vibration Sensor Fault Diagnosis and Calibration Instrument

Design and Analysis of Crushing Mill Base Vibration Isolation

Design and Development of Test and Control System for Hydraulic Steering Control Unit Based on Virtual Instrument

Design of Spectra Instant-Collection System Based on VB 6.0

Study on Hydroelectric Units Vibration Monitoring and Analysis Based on Virtual Instrument

Design and Implementation of Virtual Test System Based on LabWindows/CVI

The design of vibration testing system based on lab VIEW for wind turbine

Design and Implementation of Surveying Files Management and Query System Based on Web

Study for Vibration Measurement and Failure Diagnostics System for CNC Milling Machines Based on LabVIEW