Abstract:Vehicle weight and alternative materials development like aluminum alloys and magnesium alloys are hot issues around the world in the automobile industry. Therefore, in the present study, the structure analysis of the rear suspension 5‐links made by aluminum alloys (A356) with a tensile strength of 245 MPa, was performed using computer aided engineering to investigate the lightweight design process from the reference of the rear suspension 5‐links which was made by the steel materials and was already proven in the commercial market. Especially the simulated maximum von Mises stresses after strength analysis were normalized as the fatigue limit and were converted to the weight ratios of the same type as the fatigue safety factor suggested and referred to as such in this study. From these, it was suggested that the fatigue properties could be simply predicted only from this static computer aided engineering simulation. The weight reduction could be achieved when comparing steel and aluminum alloy models. It was a useful method to satisfy the fatigue safe design by using simple static analysis and weight factors. Das Fahrzeuggewicht und die Entwicklung alternativer Werkstoffe wie Aluminiumlegierungen und Magnesiumlegierungen sind in der Automobilindustrie weltweit von großer Bedeutung. Daher wurde in der vorliegenden Studie die Strukturanalyse der Hinterradaufhängung mit 5 Verbindungen aus Aluminiumlegierungen (A356) mit einer Zugfestigkeit von 245 MPa unter Verwendung rechnerunterstützter Entwicklungsverfahren durchgeführt, um den Leichtbaudesignprozess der Referenzkonfiguration einer Hinterradaufhängungsverbindung, die aus einem Stahlwerkstoff hergestellt wurde und sich bereits kommerziell bewährt hat, zu untersuchen. Insbesondere die simulierten maximalen von Mises‐Spannungen nach der Festigkeitsanalyse werden als Ermüdungsgrenze normalisiert und bei Beachtung der Gewichtsverhältnisse des gleichen Typs wie z. B. dem Ermüdungssicherheitsfaktor umgewandelt. Es wird vorgeschlagen, dass die Ermüdungseigenschaften nur aus der statischen rechnergestützten Simulation vorhergesagt werden. Eine Gewichtsreduzierung konnte beim Vergleich von Stahl‐ und Aluminiumlegierungsmodellen erreicht werden. Das Verfahren hat sich als nützlich erwiesen, um ein ermüdungsfreies Design durch einfache statische Analyse und Gewichtsfaktoren zu erzielen.

Failure Analysis and Structure Improved Design for Drag Link of Large Magnesium Alloy Casting Machine

Die Structure Optimization of Aluminum Alloy Wheel Low-Pressure Die Casting Based on CAE

PERFORMANCE RESEARCH ON LARGE CAST-STEEL NODE UNDER COMPLEX STRESS STATE

Component Structural Equivalent Research Based on Different Failure Strength Criterions and the Theory of Critical Distance

Optimization Design of Gelin-Bolted Joint of Magnesium Alloy Die Casting Machine

Failure analysis and structural optimization for rotary mechanism of large sling based on thermal–mechanical coupling analysis

FEA Modelling and Analysis of Die Casting Machine for Large Mg Alloy

Analysis of Forming of Automotive Drawbar and Design of the Die

Fatigue safety design of automotive suspension links by using computer aided engineering static analysis

Failure analysis of a loader hydraulic cylinder and its end cap structure improvement

FEA of solid plate weight-reduction design of large-scale magnesium alloy die cast machine

Reliability Analysis and Evaluation of Automobile Welding Structure

Determination of casting parameters of thick wall die-casting of magnesium alloy and simulation of its processing

Optimization of Main Shaft Structure of Centrifugal Casting Machine Based on ANSYS Workbench

Research on the Influence of Die Casting Process on Structure and Performance of Magnesium Alloy

Failure Analysis and Pressure Online Monitoring System Design of Casting Die Ejector Rod Based on Eigenvalue Buckling Theory

Structural Optimization Design and Strength Test Research of Connecting Rod Assembly of High-Power Low-Speed Diesel Engine

Failure analysis and improvement of a 42CrMo crankshaft for a heavy-duty truck

Thermal stress analysis and structural optimization of ladle nozzle based on finite element simulation

Degradation and failure analysis of bolted joints under transverse loading

Structural design of stamping die of advanced high-strength steel part for automobile based on topology optimization with variable density method